Haier Water Heater 40503073 User's Manual
Contents
1. before use 6 CSH10D0036 indd 2 for 2010 4 27 16 00 252. water intake take care not to hurt your hand If there is water flowing out the safety valve is working normally Please contact the local After sales Department if no water flows out In the event of damage to the safety valve please replace it with a safety valve of similar specifications Regularly engage service personnel to carry out safety inspection and promptly clear the water heating pipes of the scale Check also the consumption of the Anode rod change it if consumption becomes excessive Si Not in use for an extended period of time If the water heater is not used for an extended period of time please carry out the following steps 1 Turn off the water pipe valve 2 Screw the water drainage pipe to the safety valve s pressure relief hole turn on the safety valve handle 3 Turn the hot water valve to the maximum at the same time unscrew the soft sprinkler pipe from the water outlet valve take care not be scalded by hot water drain the inner chamber of water When the water heater needs to be used again our recommendation is to open hot water valve before switching on the power in order to prevent accidents Allow any gas that may be trapped in the pipe to be discharged Do not smoke or allow other exposed fire to be near the opened valve At the same time make sure to carefully examine all the parts of the water heater and ensure that they are in a perfect condition Make sure to fill the inner chamber with water
3. Q1 H If the heating indicator light is lit it means that the water heater is heating O heating insulation state or get closed totally 2 When the water temperature reaches the set temperature it will enter thermal state Once it lowers to certain temperature power will be automatically connected 3 Observe the water drainage of the safety valve s pressure relief hole When the water pressure is 0 75MPa and the pressure relief hole on the safety valve emits large volume of water it means that the water pressure is excessive In such case please notify the After sales Department Things to note during use Do not connect the power before filling the inner chamber with water in order to prevent damage to the water heater 2 Adjust the water temperature to the suitable level before use in order to prevent scalding 3 Insofar as there is adequate hot water set a lower temperature to reduce heat loss high temperature corrosion and scaling This will extend the water heater s lifespan 4 Do not place inflammable substances such as petrol near the water heater otherwise it may cause fire 5 To avoid danger caused by accidental resetting of the heating breaker the power for the heat cannot be supplied by timer and other external switch devices or connected to circuit with frequent switching for facility use ES6V Q2 H If the heating indicator is power off it means that heating is finished and it will
4. Troubleshooting 1 Whether the water supply has stopped or whether the Check water pressure is too low No water 2 Whether the water usage point is blocked or whether the hot water valve is opened 1 Whether hot water outlet is Check and open opened Only cold 2 Whether the water Adjust water temperature water but temperature is adjusted the heating 3 Heating time is too short indicator lamp and set temperature is not Continue heating is lit achieved 4 Whetehr heating pipe is Confirm it is not due to the reasons under damaged 2 then contact Maintenance Department 1 Whether power is proper Only cold connected Y Check power socket Water and 2 Check whether there is the heating Connect power switch a power supply indicator lamp is not lit 3 Whether thermostat is out Confirm it is not due to the reasons under of control then contact Maintenance Department Heating 1 Water has not reached the Continue heating indicator light __set temperature Is on all the 2 Whether thermostat is out Confirm it is not due to the reason under time of control then contact Maintenance Department Water volume is sometimes large or small Whether water pressure is Adjust water outflowing volume or make sure or water is stable water pressure is stable before using sometimes hot or cold Check and clear 1 Whether the present temperature setting is too Re adjust the temperature setting Samli hot er water out
5. determine the installation position of the water heater based on your needs Use PP Rpipe recommended for installation It should be such that maintenance repair and dismantling of the water heater is convenient Furthermore install loose joint at suitable locations for the water intake and outlet Use impact drill to drill two 65mm holes with a diameter of 12mm each at the locations based on the installation requirements Insert the expandable hooks into the holes and ensure that they are properly fixed Hang the water heater vertically on the expandable hooks and check whether it is securely fixed Install the safety valve and drainage pipes etc as indicated in the illustration Make sure to seal the joints with Teflon tapes to prevent water leakage Determine the water supply s position and connect the water outlet and intake to their respective positions Fill the inner chamber with water to check whether there is any water leakage If so the connections must be re done and properly carried out Note Make sure that the water heater is securely attached to the hook before letting it go otherwise it may drop and cause injury or property damage a Installation Precautions The water heater is a wall mounted type thus it should be securely mounted on the wall so that it can withstand 4 times its weight after it is filled with water Adequate space should be reserved during installation of water heater for ease of subsequent repai
6. enter Cleaning and Maintenance Warning The water heater must be repaired or maintained by qualified professionals Improper methods may cause serious injury or damage to property Note Before calling service technicians please refer to the Q amp A to solve simple issue A Cleaning E External cleaning Power must be switched off before cleaning the water heater Take a wet cloth and dab it with small quantity of neutral detergent Lightly wipe the water heater Do not use petrol or other solvents Finally use a dry cloth to wipe make use to dry the water heater thoroughly Make sure not to use detergents containing abrasive agents e g toothpaste acidic substances chemical solvents e g alcohol or polish to clean the water heater E Internal cleaning A ai i iaesso In order to ensure that the water heater will work with high efficiency clean the heating tube and inner chamber once every three years Take care not to damage lt Direction of cold water gt Direction of hot water the exterior of the heating pipe and the protective layer on the surface of the inner chamber Depending on the local water quality and usage habit the Anode rod should be regularly replaced If maintenance is required please contact the local Maintenance Department i Check When the water heater is in use the safety valve should be checked once every month To check it turn the safety valve s small handle on the side of the
7. flow volume 2 Whether water pressure is too much As far as possible reduce the water valve s outflow volume during use for details please refer to the tips in Important Notices 0040503073 V Haier Haier Home Water Heater Instruction manual ES6V Q2 H Exar ES6V Q1 H ES6V Q2 H Please read this Instruction Manual carefully before use Please retain this manual for future reference Specifications Safety Notices Please read before use Meanings of Icons S Prohibited Q Compulsory Matters A Essential Matters Forbidden Warning Caution Immediately cut off power supply and Non professionals are strictly prohibited contact our Service Center once the from carrying out repairs maintenance water heater does not work properly Or Forbidden dismantling or revamping of the water emits burnt smell heater 230V 50Hz independent power source must be used at all times Installation of water heater outdoors is strictly prohibited Wa gt 5 Ca Forbidden To ensure safety the water heater should be connected to independent sockets do not use adapters with Earthing reliable earthing In addition the power Forbidd socket must conform to national standards Use of water heater without reliable earthing is strictly prohibited Use pen multimeter to check whether the live line and zero line are reverse Do not use damaged wire and power socket Promptly c
8. he water drainage pipe to make it shorter or extend it depending on the situation Connect the other end of the water drainage pipe to the lower water outlet This will prevent the water from the pressure relief hole from splashing The water drainage pipe connected to the safety valve should be installed in a slanted manner and in an environment which is not prone to frost Make sure that the connections are not leaking and that the power supply conforms with requirements Test the machine by switching on the power Cold water pipe Connect water drainage pipe p gt After completion of installation make sure to turn on the water intake valve and mixing valve since there is no water in the inner chamber Turn the mixing valve to the maximum for hot water outlet Turn off the out flow valve when water flows out from the sprinkler or the water outlet indicating that the container is filled with water Turn off the water outlet valve Inspect all connections to ensure that there is not water leakage before connecting to power Operation Adjust the water temperature knob at the bottom of the water heater to set the temperature Maximum water temperature setting is 759 Temperature adjustment knob Turn the knob gradually clockwise to raise the temperature setting The knob will not continue to turn once it reaches maximum temperature setting Turn it anti clockwise gradually to reduce the temperature setting ES6V
9. lean the dust on the power plug and socket Do not install the water heater in an environment which is susceptible to ice formation Ice will cause the container and water pipe to break leading to scalding and water leakage Please take precautionary measures during cold weather in order to prevent damage to water heater from freezing arning If the soft power cable is damaged it must be replaced by professional staff from the manufacturers or Maintenance Department in order to avoid danger arnin Ce Warnin Check the power meter and the electric s wire s diameter to ensure that they comply with the rated current for the water heater Where necessary engage water qualified electrician to check the e Touching of hot water valve and electric circuit pipes is strictly prohibited e Make sure to check the water T Do not touch the plug with wet hands temperature before use use only N and make sure that the water heater lug socket do not come into contact Forbidden 9 Take care not to be scalded by heated Warnin Ce A fo e gt Do not use water from the water heater when it feels suitable with water If they are accidentally wet dha AT for drinking or similar purposes they must be checked by professions appointed by our company before Forbidden using in order to prevent electrocution Please cut off the power supply if the water heater
10. r and maintenance When installation care should be taken in order that the water heater is of a safe distance from gas pipe It should be at least half a meter from gas cookers gas pipe gas meter etc Make sure the pressure on the water intake is not less than 0 05MPa and not more than 0 75MPa The water heater should be installed indoors in a place where the ambient temperature is above 0 C The pipes should be closely laid out The hot water outlet should be too far away from the point of usage If the distance exceeds 8 metres the hot water pipe should have insulation protection in order to prevent heat loss Donot reverse the installation for the water intake and outlet The safety valve should be installed in the designated position and not moved without permission The safety valve s pressure relief hole should be connected to the atmosphere and free from blockage at all times To ensure safety the water heater should be connected to independent sockets do not use adapters with reliable earthing In addition the power socket must conform to national standards Use pen multimeter to check whether the live line and zero line are reverse Turn on power supply only when you have ensured that the heater is filled with water and that there is no water leakage The power supply should also conform with requirements All water pipes should be installed by qualified water pipe installation workers The pipelines should comply with
11. the national standards and regulations on the prohibition of prevention tools to draw water to water source pipelines by way of inverse siphon as well as local building codes Safety reminder In order to prevent accidents pleae use our company s accessories during installation Do not replace them on your own or use substitutes Please make sure to contact our Maintenance Department if the accessories are damaged and replace them with the accessories supplied by our company Our company shall not be liable for any direct or indirect losses caused as a result of accidents for failure to comply with the aforesaid Instruction manual 12mm Deep 65mm Expandable hook Hot water outlet Hot water ozzle PIpe N e 3 a Cold water inlet Safety valve ___ Take the installation diagram of ES6V Q1 H as an example Connection and use of safety valve Install the safety valve which has a rated pressure of 0 80MPa its connection is G1 2 into the water intake pipe with the arrow on the safety valve pointing at the water heater When the water heater is heated by electricity a small amount of water will flow from the safety valve s pressure relief hole due to the expansion of water in the heater The pressure relief hole should be connected to the atmosphere and free from blockage at all times Attach an end of the water drainage pipe onto the pressure relief hole on the safety valve You may cut t
12. was not used for an extended period of time Drain the water heater of all water according to the instructions in the chapter on Cleaning and Maintenance gt Sotring of inflammable and explosive items near the water heater is strictly Caution Forbidden prohibited Do not connect to power when installing or repairing the water heater Forbidden Introduction of exterior and accessories Back view Front view j Cut view e1 e1 Model No Net weight Volume kg L E SS eS a ___ ee 5 6 _ 100mm 364mm 266mm 100mm 285mm B Cold water intake C Heating pipe A Hot water outlet D Inner chamber E Anode rod Note The margin of error for the above parameters is 10 Technical data power frequency temperature rating pressure 230V 2000W IPX4 0 80MPa Not less than 0 05MPa eal Packing list Electric Water Safety Valve Water Instruction Expandable Product Mode Heater unit Drainage Pipe set Manual copy Hook pcs I No ES6V Q1 H ES6V Q2 H a Electrical Diagram L Brown wire N Blueline MT High temperature limiter BT Thermostat HL Heating indicator EH Heating element E Yellow green wire Installation instruction aN Se iz Installation method Must be installed by personnel in our company s After sales Department or designated installation personnel Caution The water heater is wall mounted type First
Download Pdf Manuals
Related Search