Haier Freezer DW-40L626 User's Manual
Contents
1. high temp alarm is in lighting you can set high temp alarm value If low temp alarm is in lighting you can set low temperature alarm value 1 5 Temperature setting How to unlock the control panel At the state of unlock press this key to set temperature First press up digital temperature begin to flash and press up or down and let the value to 06 then press the SET key for about 3 seconds lock light die that means it has enter unlock state Press SET key again check and set cabinet temperature high temperature alarm low temperature alarm step by step Press up and down unconsciously the temperature willbe set per 1 C and if press keys continuously the temperature value will be increased or decreased very quickly 1 6 Silence With this key you can cancel the audio sound alarm but the visual lighting alarm still flash to alarm the operator 1 7 running off When the operator need to stop the machines first cut down the power supply but the display board work all the same this function is supplied by the charge battery and then close the switch of charging battery which located at electric control box behind the cabinet2. from type to type of the appliance Technical data O woa J wows e S 2 2 5 Weight kg Dimensions 895 920 1960 DxWxH mm Packing list DW 40L626 Plastic bag Ice scraper 13 After sales service It is widely admitted that any product might go wrong From this point of view you are suggested to pay attention to and observe the performance of your appliance and changes of materials stored inside the appliance If malfunction occurs make analysis and try to eliminate abnormal symptom according to the instructions stated hereinafter Only call the service department if you cannot find any cause for the defect or you are not able to eliminate the fault after analysis of the possible fault factors The appliance does not operate Incorrect voltage of power supply Correct voltage is 220V Power source not switched on Thermostat is not correctly set up The appliance is too close to heat source The appliance is located too close to the wall The condenser is dusty Clean the condenser with a brush Large quantity testing samples are loaded in the most recent a few hours in such case set the thermostat to higher temp scale and lower the setting when the appliance is in normal operational status Frost buildup forms on interior Materials in storage contact each other Space the materials walls or around the doorframe or wrap the materials if moisture is contained inside the material
3. on the appliance and load materials when set temperature is reached Out of service If the appliance is not used for an extended period disconnect the appliance with power supply wipe down the appliance open the door and remove all the materials If the appliance is to be discarded dispose the appliance to authorized collection center 2 Remove the materials in storage before defrosting the appliance In defrosting process keep the appliance door open for ventilation 4 It is suggested that a bowl with 50 C water be placed inside the appliance to shorten the defrosting period Warning Never use an electric or sharp metal tool to remove the frost 2 Adjust the setting value 2 1 high temp alarm setting During high temp alarm setting the digital Temperature value will be in flashing condition the operator adjust the alarm value by up and down key After adjustment keep 10s the control panel will enter the locked condition automatically and the digital displayer stop flash which means your setting success Otherwise you didn t change the setting success When the cabinet temperature is higher than high temp alarm value the equipment will alarm the operator And do not set the alarm value lower 5 C than cabinet temperature setting value 2 2 low temp alarm setting During low temp alarm setting the dig
4. Deep Freezer User s manual DW 40L626 Please read this manual carefully before using Retain it for future reference Read this User s Manual carefully before using the appliance Look after this Manual so that you may consult it in future Table of Contents Primary 1S ISS ata ascrescssersscassagaoamasiacesentaeesacecencaussabootensaqomaridacsoniesvetes nemuesaveneeass l Diagram OF Pans titeeteseresecnatuadeesataconteannet ep E ESEE 2 Safety Precaullong esere ieSe e EE 3 mMstalat n lOcaUOM sesreeseeiririciriiyirsiciniia annod Tini enan o AEEA EA 4 Preparation and operation instructions ccccceeesssssscceeeececcecececeeeseessessssaeeeeees 5 CONTO TO AIMS ariran E E E EE E AEA 6 Functions and operational instructions of control panel ecceeeeeseteeeeeeeees 6 1 Control panel displayer sary svassersasivecterardcvacsedastanenveniersdsracedeesenaeedoueiiacs 6 2 Operation MAM OGUCU ON sesatecesecsiceeeicdanatteedesgntetedtpotenataseenenatesedsorneces sheds g Defrosting and out Of SEPVICE cece ccccsssecesssseeeessscecessseeeeseseecesesaeecessaeeseseaeees 9 O ca see cane gue bacetesqase EE A E 10 WVU SS TOOT Neve ca vecevssercosonecauccesndsceucucectesorcasnonesdatses dunn enecasauidancnsnanieeeauceneoreaceers 11 PGT Sales SENICE apresen enei t E Ea 12 Mee ai e cike ii EE A E EEO EE O E E ET 13 PACING GT epinio E E dendse senetoapncanteraantnecaadecdte 13 The design color and door pattern may vary
5. Temp C Power Failure C Hot Condenser Functions and operational instructions of control panel 1 Control panel displayer 1 1 Temperature display After the appliance is initiated the actual temperature set temperature ambient temperature and voltage are on display 1 2 Alarm The condenser is dusty please clean it is on display if the condenser needs to be cleaned room temperature is not proper is on display if ambient temperature is high room temperature is not proper is on display if ambient temperature is low Sensor error E2 is on display if the main sensor does not work properly and the alarm is activated If the condenser sensor does not work properly Sensor malfunction E1 is on display If the ambient temperature sensor does not work properly Sensor malfunction EO is on display 6 If input voltage is over high the booster will be activated and Voltage boost is on display If input voltage is over low Voltage too low is on display and the compressor can t be opened 1 3 Malfunction and status indications a When copressor is in operation compressor is on display b Network indicates the network system is in working status c Lock on indicates all setups are locked in order to avoid incorrect operations 1 4 set when the control panel is out of locked repress the set key and Temp Inside is in lighting you can set this value If
6. fore power on please do switch on the charge battery switch of the electric cabinet at the back of the machine can be seen at the back of the machine about the charge battery switch fixed on the electric cabinet and the charge battery switch is at the right up of the outlet of the electric cabinet power cord If the ambient temperature is over 28 C please cool down the temperature If the ambient temperature exceed 32 C please do not operate the freezer otherwise the compressor will be damaged easily This appliance is designed for storage not production Always make sure that appropriate materials are to be stored Do not load hot materials in the appliance otherwise the compressor might be damaged due to excessively extended operation period Materials should be loaded separately by regulated volumes and temperature be lowered by phases until desired temperature is reached Please operate the machine as above process which will make the equipments running in a good working condition and longer using life Control panel The control panel is located on the door of the appliance The diagram of the control panel is as follows Alarms Working Condition 40 0 C C High Temp C Probe Failure C Compressor C Low Temp Low Battery CI Network CJ Inner Temp C High Temp Alarm SET E Locked C Low Temp Alarm J Improper Voltage C High Ambient Temp a Goo E Boe Haier Deep Freezer Voltage Ambient
7. ital temperature value will be in flashing condition the operator adjust the alarm value by up and down key After adjustment keep 10s the control panel will enter the locked condition automatically and the digital displayer stop flash which means your setting success Otherwise you didn t change the setting success When the cabinet temperature is higher than high temp alarm value the equipment will alarm the operator And do not set the alarm value higher 5 C than cabinet temperature setting value NOTE ULT freezer should be in charge of special person and check and record the operation condition in everyday If it meet power cut or any other failures and the freezer doesn t work the temperature inside cabinet will increase And if there will be without power for a long time please get out the storage and load them into other low temperature container for avoiding samples damage Please confirm again the temperature inside freezer is what you need before you load the goods into freezer otherwise it will be make damage to the goods for improper temperature Preparation and operation instructions Unpacking 2 Check attached Remove all packing accessories and materials materials IS Check if all accessories specified in the Packing List are available 3 Clean the appliance See section Cleaning Leave the appliance standing in its final position for at least 24 hours before switching it on Be
8. m that of the product you have just purchased due to technical improvement Diagram of parts Troubleshooting Control Panel The following events cannot be prevented When the appliance is first initiated the appliance will keep operating for an extended period and generate large noise Handle Compressor Cabinet Foaming Door Dear customer Thank you for your choice of Haier product Haier product has combined the advantages of high technology and good quality and performance For the convenience of your use please read carefully the instruction manual and follow its practice All along Haier s International Star rating service will company you Whenever any problem happens in your use please contact us and our distributor whom you purchased and from we are always at your service One more time we thank vour for vour use and introduce of Haier Cleaning Unplug the appliance before cleaning is carried Use a piece of soft fabric or sponge damped by out for the appliance water or soapy solution noncorrosive mild detergent liquid to clean the appliance Finally wipe down cleaned appliance with a piece of dry fabric to avoid potential of rust Clean the condenser compressor and piping Never use organic dissolvent boiling water system regularly with a soft brush for a better washing powder or acidic liq
9. ppliance Installation location The appliance should be located on a solid surface without any packing material When the appliance is moved never tilt it over 45 nor apply force on pipes door and or handle otherwise damages may result The appliance should be kept clear around for good ventilation ow 4 Do not locate the appliance at a damp area or near a sink to avoid water splashes Wipe down the appliance with soft fabric Keep the appliance away from direct sunlight or heat source The appliance should be operated with an ambient temperature below 32 C Do not operate the appliance in temperature below 5 C The best ambient temperature for the appliance is 18 C 25 C Q Caution indicates operations that should be avoided as injury to the operator or damage to equipment may result S Y warring indicates operations that should be avoided as fatal injury to the operator may result Defrosting and out of service 1 After a period of operation frost may build up on the walls in freezer compartment If frost buildup reaches 10mm additional electricity is consumed In such case remove the frost with a plastic scraper provided by the manufacturer KI 3 After defrosting wipe down the appliance with a piece of soft fabric or sponge and then switch
10. s Appliance door is not properly closed Do not open the appliance door unless it is necessary Large noise The appliance is not placed on a flat surface The noise is generated by compressor Usually the in ultra low temperature equipment generates louder noise than that of household appliances Noise of banging The noise might be generated by the appliance parts due to sudden shrinkage It is suggested that temperature is decreased gradually not swiftly 12 This appliance should not be used for storage of live creatures or fresh flowers which have special requirement in temperature Primary features e Microprocessor control digital temperature display and temperature range 10 C to 40 C normally running range from 20 C to 40 C e Several protection function compressor delay protection booster for low or high voltage protection e Excellent auto cascade cooling technology and imported compressor make a more better cooling capacity of freezer e Intelligent LED displays on the freezer can display the cabinet temperature set point ambient point input voltage which also can be set the high and low alarm temperature and indicate the operator the failure in process in the display e Creative whole door lock and handle and with tight castors e Application in hospitals epidemic prevention service research institutes and plants Technical data in this manual may vary fro
11. uid for cleaning of the cooling performance appliance Safety precautions This appliance requires 220V 50Hz supply A regulator with a capacity of 4000W or higher must be installed if the voltage is below 198V or higher than 242V If the electric cord is to be extended the wire with a cross section 22mm and length less than 3 meters can be used Never store inflammable explosive or corrosive materials in the appliance If inflammable gas leaks in the vicinity of the appliance Turn off any leaking valve Open doors and windows Do not plug or unplug the appliance Allow a 5 minute lapse before restarting the appliance if power is interrupted and then resupplied for safety of the compressor and cooling system Unplug the appliance when repair or maintenance is intended On A separate earthed socket is required The appliance is supplied with a standard three pin plug of which the one for grounding should never be removed Warning The electric plug should firmly secured in the socket otherwise fire may result Do not use inflammable spray near the appliance Never allow children enter the appliance to avoid accidental entrapment Danger Protect your hands from frost damage when you are loading or unloading the a
Download Pdf Manuals
Related Search