Haier HA600TE User's Manual
Contents
1. Trouble shooting The following circumstances do not constitute problems Do not contact the maintenance service until the problem has been confirmed Problem Possible Cause Poor connection to power supply The washing machine fails to Power failure operate Door is not properly closed Machine has not been switched on Water is not turned on Water pressure is less than 0 03MPa Washing machine does not fill The inlet hose is kinked with water Water supply failure The program knob is not properly set The door is not properly closed The water supply and Check that the height of the water hose is below drainage do not stop 80cm Drainage hose is blocked Drainage hose end is below 100cm above the floor level Drainage failure Some packing fixing bolts removed Strong vibration during spin Washing machine on a uneven surface Operation stops before comple tion of the wash cycle Water or electricity failure Excessive foam in the drum The detergent is not a low foam type Excessive detergent has been used 14 Technical Specification 1000 800 600 Power supply 220V 240V 50Hz 220 240 50 2 220V 240V 50Hz Water pressure MPa 0 03 lt P lt 1 0 03 lt P lt 1 0 03 lt P lt 1 _ 850x520x595 850x520x595 850x520x595 Net Weight Wiring Circuit CN1 2 CN2 1 CN1 3 1 1 CN3 3 CN32. be less than 15 Power supply voltage conforms to the required value The power supply socket and the plug of the washing machine compatible if they are compat ible Refer to a washing machine technician or a Haier designated service point for power cable replacement The washing machine should be connected to an earth before use Supplementary earth cable should not be necessary if the socket is connected to the earth Supplementary earth cable should be installed on the upper back of the washing machine andconnected to an earth if the power supply socket has no earth connection Control Panel G MAHRI A Washing program Turn the knob to set the desired wash program Caution Turn the knob at 0 then turn off the power and turn the program knob for setting desired wash program The program knob will not rotate with the programmed washing process B Washing temperature Turn the knob to set the desired temperature Temperatures between 30 C 90 C canbe setted No heating wash is selected when the knob is set at Operational Functions C Detergent distributor Program discription are printed on the handle of the detergent distributor there are three detergent compartments numbered 1 2 3 Box 1 Pre washing detergent Box 2 Standard washing extra fast washing Box 3 Softening age
3. bed lt S fabrics 50g sheets cotton 800g Woolen blankets 30000 cotton 800g 2 Use of detergent Pull out the detergent drawer put required detergent soften ing agent and bleaching agent into the corresponding boxes Push back the drawer gently Caution 1 Do not add liquid detergent into box 1 and 2 2 For pre washing program detergent should be added to both box 1 and 2 for other programs do not add detergent to box 1 3 Do not overuse softening agent as this may damage artificial fabrics 3 Washing program setting Set the wash program correctly in accordance with the laundry load The methods for setting wash programs are indicated on the handle of the distributor on the washing machine Turn the program knob to the desired program Caution If you want to choose another program first turn the program knob at 0 then turn off the power and turn the program knob for setting desired program Washing Methods 4 Washing temperature Setting Set the washing temperature as required otherwise set at position when heating is not needed 5 Selecting the function button Select function buttons as required refer to the directions printed on the control panel otherwise keep all the button released 6 Washing Press the power button and the washing machine will automatically commence the pro grammed washing process Caution The program knob will not rotate with the programmed washin
4. sure that the washing machine is securely connected to the water supply take the necessory precautions or contact the local service center if the connection is poor or there is a water leakage 9 The washing machine should be place in a well ventilated area maintaing space between walls or furniture 11 During installation ensure that the electric cable is not trapped by the washing machine and avoid damage to the electric cable Dear customer For the machine and your own security DO NOT REPAIR IT BY YOURSELF DO NOT USE THE WASHING MACHINE WHICH SOME PARTS ARE LOST 2 After turning the power off turn the pro gram knob clockwise to set washing program Matters Needing Attention 3 Never place heavy objects a heating 4 Donot wash foam rubber or similar sponge applianceor a water container on the top panel materials of the washing machine 5 Before washing do up zippers buttons laces and repair damaged areas under wear or small articals should be placed in the laundry bag or a pillowslip Do not wash clothes containing wire frames 6 Do not open the detergent box during the wash cycle 7 The door is fitted with self lock device and 8 After washing turn off the tap to prevent will not open until 2 3 minutes after the wash leakage unplug the washing machine ing machine stops Do not force the door and wipe clean the lower part of the port open Do not open the door when water level ho
5. 1 CN2 2 CN6 4 CN6 3 cons PCB ON CON2 OO CN2 3 OG CON1 CO ZL 2 CN2 4 CN2 5 CN2 6 CON3 CN3 3 CN3 4 e 12 13 es R 14 1 P PCB Printed Circuit Board Motor Motor MR Door Lock R Heating Element PS Drain Pump P Pressure Switch EVP EVF Cold water Valve EVS Hot Water Valve FA Interference Suppresser NTC Temperature Sensor SW Power Switch Motor Motor 16
6. Automatic Drum Ha ier Washing Machine HA1000TE 800 600 Table of Contents Before using Names of Parts inside front cover Matters Needing Attention 1 3 Installation 4 5 Control Panel 6 Operational Functions 6 7 During using Program Selection 8 Preparation _ _ 9 Washing Methods 10 11 Other Function 12 Maintenance Maintenance T 13 Trouble Shooting 14 Wiring Circuit q 15 Technical Specification 16 Names of Parts gt Table Cover Washing Allocating box Operation Button Program Knob Wash Door Observing Glass Window Temperature knob Power supply cable Earth terminal Drainage hose clip Back plate screw 3 Packing bolt 3 Drainage hose Back plate Caution and Warning symbols For your safety any instructions in this manual with this Warning sign shall be strictly followed For your safety and to prevent damages to the washing machine any instructions in this manual with this Stop sign shall be strictly followe
7. d This diagram may vary slightly with the layout of the washing machine you have just purchased due to technical improvements Matters Needing Attention Safety 1 Aseparate earthed socket is required for the power supply After installation of the washing machine the power plug should be accessible during the normal wash 3 Fuses in the power circuit should be rated for 15A Refer to a washing machine techni cian or a Haier designated service point for power cable replacement A 5 Do not use flammable detergent or dry cleaning agent do not use flammable spray in close vicinity to the washing machine do not remove or insert the plug in the presence of flammable gas 2 Hold the plug and not the electric cable when unplugging the washing machine 4 For your safety dry hands before touch ing the washing machine and wear appropri ate footwear as 6 The door of the washing machine will be come hot during the water heating process Avoid contact with the door during the heat ing process For safety keep children away from the washing machine Matters Needing Attention 8 The washing machine must not be used in the open or in area of high moisture as water droplets may form on electrical components Air dry the appliance if the washing machine components become wet 10 Keep away from heat sources and direct sunlight to prevent plastic and rubber com ponents from aging Use 1 Make
8. ee types of clothes cotton synthetical and woolen silk fabrics separate white clothes from colored If whites and coloreds are combined for one load make sure the coloreds are colorfast Remove all objects from pockets that may cause dam age to the machine such as keys and coins gt Clothing with frayed edges or yarns should be putin wash bag or special bag before washing Repaire damaged clothing lose buttons or damaged zips and hooks before washing Bed sheets and table ware should be loosely loaded and not folded This washing machine is for household use and de signed for mechanically washable clothes When washing separate unwashable clothes with reference to clothes labels Type Non fade cottons Delicate fabrics Woolen fabrics Blending fabrics Max load 1kg 2 5kg 10 Washing Methods 1 Laundry loadin undry ing Reference loading Evenly load the laundry in the washing machine and then tightly close the door of the washing machine Blended Note 1 When first using the fabric clothes l N 7 2 77 washing machine let it run un 800g Shirts loaded for one program to pre 6 nderwear ended fabrics 70g Overalls Jeans 8000 cotton 9509 lt gt Pajamas 200g vent the laundry from being tainted by oil or dirty water from cotton the washing machine 2 Do not 300g Socks overload the washing machine Single
9. elicate Fading and medium soiled chemical fiber Normal Non fade heavily soiled woolen fabrics Wool Delicate Fading and medium soiled woolen fabrics Normal Non fade heavily soiled silk fabrics Silk Delicate Fading and medium soiled silk fabrics Quick Medium soiled lanudry Rinse X 16 OR OR oe gt Ob 6 Spin X X NOTE End means softener liquid detergent canbe added when necessary Turn the program knob at 0 position and turn off the power The wash program ends and the washing machine stops operation means detergent can be added when necessary means no detergent can be added 1 Power supply Plug in the power supply 220V 240V 50Hz 4 Detergent selection Only special low foam detergent should be used in automatic drum washing machine form blended or wool fabrics special detergent should be used dry cleaning solvent should not be used such as trichhloroethylene or alike caution load the re quired amount of detergent only 5 Wash Load 2 Water supply Turn on the tap ensure that the water is clear Caution Before staring the washing machine turn on the water faucrt to ensure that the water faucet and the water inlet hose are connected correctly and do not leak 3 Laundry treament sort out clothes according to type and extent of dirt There are thr
10. g process Wait 2 3 minutes after the washing process is finished press the power button again to cut off the power supply Open the door to take out the laundry Turn off the tap and unplug the washing machine Caution When the washing program finishes the door lock light will glitter before the door can be opened Additional information Energy and water saving during wash process 1 Collect clothes for one full wash load 2 Do not overload the washing machine 3 Prewash heavily soiled clothes 4 Reduce the amount of detergent or choose fast or minimal washing programs for lightly soiled clothes dirty Choose a proper washing temperature Only exceed 60 C for heavily soiled clothes Do not use more detergent than required Softening agent makes clothes feel softer and easier to iron 11 Other Functions 1 Power off memory funtion This machine has a power off menmory funtion In case of abrupt power failure or the power must be cut off during a program cycle the present settings will be saved and operation will resume when the power is switched on again 2 Trouble messages judge the malfunctions from door lock light Error 1 The door lock light does not illuminate Cause Door is not properly shut Correction Shut the door properly Error 2 The door lock light glitters 2 times and stops 4 seconds repeatedly Cause Drainage error water not emptied within 4 minutes Correction Clean the f
11. ilter and check the drain hose for blockage If error still exists please contact the maintenance personnel Error 3 The door lock light glitters 3 times and stops 4 seconds repeatedly Cause Temperature sensor not properly connected or damaged Correction Contact the maintenance personnel Error 4 The door lock light glitters 4 times and stops 4 seconds repeatedly Cause Heating coil damage or overload of laundry that leads to a failure to reach the set temperature within the specified time This message 15 display at the end of a program Correction Reduce load and then start washing again or contact the maintenance personnel Error 5 The door lock light glitters 5 times and stops 4 seconds repeatedly Cause Water level not met in 8 minutes Correction Make sure that tap is turned on and water pressure is normal If problem still exists please contact the maintenance personnel Error 6 The door lock light glitters 6 times and stops 4 seconds repeatedly Cause Timing control silicon damage Correction Contact the maintenance personnel Error 7 The door lock light glitters 7 times and stops 4 seconds repeatedly Cause Motor overheat protection or damage Correction Contact the maintenance personnel Error 8 The door lock light glitters 8 times and stops 4 seconds repeatedly Cause Water exceeds protective level Correction Contact the maintenance personnel 12 13 Maintenance 1 Turn of the water and elect
12. ing machine Please connect the straight terminal of the inlet hose to the water tap and make sure to fasten it Please connect the bended terminal of the inlet hose to the solenoid valve and make sure to fasten it NOTE Please be sure that the COLD inlet hose is connected with the solenoid valve for cold water marked with C Water drainage hose The height of the terminal of the water drainage hose should be between 80cm 100cm the water drainage hose must be securely placed on the clip on the back of the washing machine Use the water drainage support supplied as an accessory for proper installation of the water drain age hose fix the water drainage hose support with waterproof sring Do not use an excessively long wa ter drainage hose and contract the authorized tech nician if the water drainage hose needs to be extended the water drainage hose should not be ex tended more than250cm longer extension will result in concurrent water inflow and outflow The diam eter of the extension hose should be the same as the original hose caution water drainage hose must not be immersed in water the original and extension hoses should be tightly connected Connection of power supply Check the following items before connection to the power supply The socket conforms to the maximun power load The maximum current load of the socket and power supply cable should not
13. le reaches the port hole 9 Keep the door slightly open when the washing machine is not being used Never cover the machine with a plastic sheet Installation As shown in figure1 remove all the packing materials including the foam base Upon opening of the package water drops may be seen on the plastic bag and the porthole This in normal phenomenon resultingfrom water test in the factory Check attachments and materials Operational Quality Drainage Plastic manual certificate holder plugs Model HA1000TE 800 600 Remove the packing screws shown in figure 2 The packing bolts protect the appliance from shock during trans portation The steps below should be followed before using the appliance 1 Remove the rear panel of the washing machine 2 Remove the three packing bolts from the rear panel of the wash ing machine the rubber hose and then the shock absorption chan nel steel 3 Reinstall the back plate 4 Fill the holes left by the packing bolts with plastic plugs Attention the packing bolts and rubber hose should be kept in a safe place for later use Adjusting the position of the washing machine There are ad justable feet under the bottom of the washing machine Before use the washing machine should be adjusted as shown in figure 3 so that it is level Installation Connection of water inlet hose and wash
14. nt adjusting agent perfume D Soak Button For the synthetics cycle and the wool cycle push the button down the anticrease funtion willbe skiped and automatically enter into the next step Release the button the anti crease funtion will work again E Economic Wash button It reduces water and power consumption when rinsing if the machine does not have a full load Note Select this function when Cotton Synthetics Wool or Silk programs 1 12 is selected F Power button ON Press the button washing machine will working release the button the washing machine will stop OFF G Door light The light will illuminate when the door is locked H Power light The light will illuminate when the power supply is connected Program Selection 1000 800 600 Laundry Temperature Detergent Comp 1 prewash detergent Comp 2 detergent Comp 3 softener Intense Very heavy soil 30 40 50 60 70 80 90 k Prewash Heavy soil 30 40 50 60 Normal Soiled cotton 30 40 50 60 Middle Non fade and medium soiled cotton 30 40 Delicate Fading and medium soiled cotton Normal Non fade heavily soiled chemical fiber 30 40 50 60 Middle Non fade and medium soiled chemical fiber 30 40 5 gt 0 D
15. ricity supply af ter every wash Open the door to prevent the formation of moisture and odors If the wash ing machine is left idle for a long period drain any remaining water in the machine and re place the drainage hose 4 Cleaning the Filter once a month Press the lower edge of the filter compartment cover to open Fig1 2 Remove the filter by turning counterclockwise Fig3 Flash clean with running water Filter replacement is the reverse of removal Caution Attention shall be paid to ensure that the filter is replaced correctly to avoid possible leakage 2 Unplug the machine during cleaning and maintenance Use a soft cloth dampened with soapy liquid to clean the machine case and rubber components Do not use corro sive or abrasive chemicals or solvents 4 To prevent blockages to the water supply or the ingress of contaminants clean the water inlet and inlet water filter regularly 5 If the machine is to be moved a distance location 6 If the washing machine is left idle for a long period turn off the replace the vibration mounting locks which were re moved during installation as shown below water and electricity supply and open the door slightly to prevent the formation of moisture and odors fl Fas Remove the back Replace the rubber cover Tighten the bolts with a spanner Insert the bolts plugs Replace the back cover
Download Pdf Manuals
Related Search