Haier DW12-CBE7 User's Manual
Contents
1. Haier Domestic Dishwasher DW12 CBE7 i z E E Code 0120504356 Safety Is a Good Habit to Get Into NOTICE Carefully read the instructions contained in this manual as they provide important information which is essential to safe and proper installation use and maintenance of the appliance This appliance complies with following EEC di rectives 73 23 EEC of 19 02 73 Low Voltage and subsequent modifi cations 89 336 EEC of 03 05 89 Electromagnetic Compatibility and subsequent modifications Carefully dispose of the packing material After removing the packing check to make sure that the appli ance is not damaged If in doubt contact a qualified professional The dishwasher must only be used by adults for the washing of household dishes and cooking utensils Fundamental rules to follow when using the appliance Never touch the dishwasher when barefoot or with wet hands or feet We discourage the use of extension cords and multiple sock ets Close up View control panel During installation the power supply cord must not be exces sively or dangerously bent or flattened If the appliance is not operating properly or maintenance must be performed disconnect the appliance from the power supply Keep detergents out of the reach of children who must also be kept away from the dishwasher when it is open This appliance cannot be installed outdoors not even if th2. in an anti clockwise direction and then pour in the rinse aid making sure not to overfill The amount of rinse aid used for each cycle can be regulated by turning the F dose adjustor located beneath the C cap with a screwdriver There are 6 different settings the normal dosage setting is 3 Important Proper dosage of the rinse aid improves drying If drops of water remain on the dishes or spotting occurs the dosage adjustor should be turned to a higher setting If the dishes have white streaks turn the dosage adjustor to a lower setting Loading the Dishwasher Before placing the dishes in the dishwasher remove larger food particles to prevent the filter from becoming clogged which re sults in reduced performance If the pots and pans have baked on food that is extremely hard to remove we recommend that they are soaked before washed This will eliminate the need for extra wash cycles Pull out the rack to load the dishwasher How to use the lower rack We recommend that you place the most difficult to clean items on the bottom rack pots pans lids serving dishes and bowls as shown in the figure to the right It is preferable to place serving dishes and lids on the sides of the racks in order to avoid blocking the rotation of the top spray arm Pots serving bowls etc must always be placed face down Deep pots should be slanted to allow the water to flow out The lower rack features fold down tine r
3. be positioned to the right or the left to facilitate proper installation Levelling the Appliance Once the appliance is positioned adjust the feet screwing them in or out to adjust the dishwasher making it level In any case the appliance should not be inclined more than 2 If the appli ance is level it will help ensure proper performance Cold Water Connection Connect the cold water supply hose to a threaded 3 4 gas connector making sure that it is fastened tightly in place see fig 2 Some models are fitted with an Aquastop water supply hose see fig 1 in which the small filter is already housed in the threaded end If the water pipes are new or have not been used for an extended period of time let the water run to make sure that the water is clear and free of impurities If this precaution is not taken there is a risk that the water inlet can get blocked and damage the appliance Hot Water Connection The water supply to the appliance can also be connected to the house s hot water line centralised system heating system as long as it does not exceed a temperature of 60 C In this case the wash cycle time will be shortened by about 15 minutes and the wash efficiency slightly reduced The connection must be made to the hot water line following the same procedures as those for the connection to the cold water line Anti Flooding Protection The dishwasher is equipped with a system that stops the supply of wate
4. dishes and utensils The appliance is equipped with a special softener that uses a salt specifically designed to eliminate lime and minerals from the water Loading the Salt into the Softener Always use salt intended for use with dishwashers The salt container is located beneath the lower rack and should be filled as follows Remove the lower rack and then unscrew and remove the cap from the salt container If you are filling the container for the first time fill it with water Place the end of the funnel Supplied into the hole and intro duce about 2 kg of salt It is normal for a small amount of water to come out of the salt container Carefully screw the cap back on The salt container must be filled when the low salt indicator light located on the control panel comes on To prevent the formation of rust load the salt just be fore beginning a wash cycle Adjusting Salt Consumption The dishwasher is designed to allow for adjusting the amount of salt consumed based on the hardness of the water used This is intended to optimize and customize the level of salt consump tion so that it remains at a minimum To adjust salt consumption proceed as follows Unscrew the cap from the salt container There is a ring on the container with an arrow on it see figure to the side If necessary rotate the ring in an anticlockwise direction from the setting towards the sign based on the hardn
5. e area in which it is installed is covered by a roof it is also very dangerous to leave it exposed to the rain and elements Do not touch the heating element during or after a wash cycle Do not lean or sit on the door when it is open as this could overturn the dishwasher If the appliance malfunctions turn off water supply to the appli ance and disconnect the plug from the wall socket Then con sult the section entitled Troubleshooting If you cannot re solve the problem contact a service centre Only specialised personnel are authorised to make repairs Appliances which are no longer being used must be made inop erable by cutting the power supply cord and removing the door lock CBA A ON OFF Light B ON OFF Button C HALF LOAD Button D Low salt indicator light E Low rinse aid indicator light F Cycle indicator light Close up View Interior V J L E Upper Rack F Top Spray Arm G Rack Height Adjustor H Lower Rack Washing Filter Technical characteristics Width Depth Height Capacity Mains water pressure Power voltage Total absorber power lt FA CG im mG m Salt Container Cap Bottom Spray Arm Detergent and Rinse Aid Dispenser Third Sprayer 60 cm 58 cm 82 cm 12 standard place settings 0 03 0 6MPa 220 240V 50Hz 2150W Salt Bate Salt The hardness of the water varies from place to place If hard water is used in the dishwasher deposits will form on the
6. e on the rating plate located on the stainless steel inner door of the appliance and that the electrical system is correct for the maximum voltage on the rating plate insert the plug into an electrical socket which is earthed properly the earthing of the appliance is a safety re quirement mandated by law If the electrical socket to which the appliance must be connected is not appropriate for the plug replace the plug rather than us ing adaptors or the like as they could cause overheating and burns Caution The dishwasher plug must be accessible even when the appli ance is installed as a built in unit so that maintenance can be done safety Installation
7. ess of the water being used It is recommended that adjustments be made in accordance with the following schema Clarke Selector oa mmol l consumption degrees position Grams cycle 14 36 18 44 1 8 TIE Autonomy cycles 2kg 0 1 7 gt 17 36 71 45 89 45 vee Detergent and Rinse Aid Detergent Detergent specifically intended for use with dishwashers must be used The dispenser must be refilled before the start of each wash cycle following the instructions provided in the Wash Cycle Table The detergent dispenser is located on the inside panel the door Loading the detergent To open the A cover on the dispenser press the B button The detergent for the wash cycle should be poured into the C compartment After the detergent has been placed in the dispenser close the cover and press down until it clicks in place Notice To facilitate closing the cover remove any ex cess detergent on the edges of the dispenser Rinse Aid This product makes dishes sparkle and helps them to dry with out spotting The dispenser is located on the inside panel of the door and should be filled after every 80 wash cycles or when the low rinse aid indicator light comes on for those models with this feature Loading the Rinse Aid Regardless of the type of detergent dispenser installed on your appliance you must proceed as indicated below when loading the rinse aid To open the dispenser turn the C cap
8. ilter use a cleaning brush Then reassemble the filter parts as shown in the figures below and reinsert the entire assembly in the dishwasher positioning in its seat and pressing downward The dishwasher must never be used without the filters Improper replacement of the filters may re duce level of the appliance and damage dishes and utensils When You Go on Holiday When you go on holiday it is recommended that you run a wash cycle with the dishwasher empty and then remove the plug from the socket turn off the water supply and leave the door of the appliance slightly ajar This will help the seals last longer and prevent odors from forming within the appliance Moving the Appliance If the appliance must be moved try to keep it in a vertical position If absolutely necessary it can be positioned on its back Seals One of the factors that cause odors to form in the dishwasher is food that remains trapped in the seals Periodic cleaning with a damp sponge will prevent this from occurring Cleaning the Spray Arms It may happen that food particle become encrusted on the spray arms and block the holes Check the spray arms periodically and clean them when needed Cleaning the Water Inlet Filter Periodically clean the water inlet filter see figure located on the outlet of the water supply tap After turning off the water tap unscrew the end of the water sup ply hose remove the filter and clean it carefully under run
9. ipped with a safety system that is able to detect operating problems and malfunctions These malfunctions are signalled by the rapid blinking of one of the M program LEDs Only in the case where the indicator light for the soak cycle see table for cycles blinks rapidly should you cancel the cycle as described in the section entitled Changing a Cycle while Underway Then check to make sure that there is water in the mains and that the tap is turned on If the message continues call for technical assistance indicating which message appeared If any of the other indicator lights begins to blink rapidly turn off the appliance and call for technical assistance indicating which light began to blink If despite all these checks the dishwasher still does not func tion and or the problem persists contact the nearest authorised service centre and provide them with the following information the nature of the problem the model type number Mod And the serial number S N which are indicated on the plate located on the side of the inner part of the door Never call on unauthorised technicians and refuse to allow parts to be installed that are not original spare parts Installation Positioning the Appliance Positioning the appliance in the desired location The back should rest against the wall behind it and the sides along the adjacent cabinets or wall The dishwasher is equipped with water supply and drain hoses that can
10. ng this period the delay indicator light D will blink At the end of the delay time the indicator will stop blinking and the cycle will start NOTE a During the delay period none of the settings can be modified If necessary they can be cancelled by pressing cycle selector P for about 5 seconds b If the power to the appliance goes off or the door is opened during the delay period the clock will stop the countdown It will start again when the power has come back on or when the door has been closed Wash Cycle Adjustment Buttons 1 2 Load Button This button see Close up View Control Panel letter Q makes it possible to wash dishes using only the upper rack if there are not enough dishes for a full load This will allow you to save on water and electrical energy It cannot be used with the heavy duty wash cycles Wash Cycle Table rin Energy Saving Tips It is important to try and run the dishwasher when it is fully loaded in order to save on energy In order to prevent odors from forming and food from caking onto the dishes you can run the hold cycle Choose the right wash cycle the choice of cycle depends on the type of dishware cookware and utensils being washed and how dirty they are Use the right amount of detergent if you use too much detergent the result will not be cleaner dishes but rather a greater nega tive impact on the environment There is no advan
11. ning water Then return the filter to its place and tighten the water supply hose back into position Troubleshooting It may occur that the dishwasher does not function or does not function properly Before calling for assistance let us see what can be done first have you forgotten to press one of the buttons or to perform an essential operation The Dishwasher Does Not Start Have you checked whether the plug is pushed into the socket correctly the power is on in the house the door is closed properly the ON OFF switch is on ON the water supply is turned on The Dishwasher Does Not Load Water Have you checked whether the water is turned on and the hose is connected properly the water supply to the house is on and has sufficient pressure the water supply hose is crimped or bent the filter for the water supply hose is clogged The Dishes Are Not Clean Have you checked whether the water is turned on and the hose is connected properly the water supply to the house is on and has sufficient pressure the water supply hose is crimped or bent the filter for the water supply hose is clogged The Dishwasher Does Not Drain Have you checked whether the drain hose is crimped or bent Lime Deposits or a White Film Form on the Dishes Have you checked whether the lid to the salt container is closed properly the rinse aid dosage is correct Error Messages The dishwasher is equ
12. on the water to the unit partially open the door of the dishwasher and press the ON OFF button A lo cated on the control panel The B indicator light will come on At this point the appliance is on and ready to be programmed Setting and Starting a wash Cycle Choose the desired cycle by pressing the cycle selection button P Each time it is pressed one of the cycle indicator lights M will come on in succession Choose the wash cycle you feel is most appropriate for the type of dishes that need washing consult the wash cycle table con tained in this manual especially when first using the appliance Close the door and after a few seconds a short acoustic signal will sound indicating that the wash cycle has begun and cannot be modified If necessary read the paragraph entitled Cancel ling or modifying a cycle while underway The end of the cycle will be signalled by a double acoustic sound and the indicator light M will begin to blink Cancelling or modifying a cycle while underway Premise A cycle that is underway can only be modified if it has only been running for a short time Otherwise the detergent may have already been used and the appliance may have already drained the wash water If this is the case the detergent dispenser must be refilled see the paragraph entitled Loading the Detergent To change the cycle currently underway open the door press the P programming button and hold it in for abo
13. ows see fig A so that larger or more pots and pans can be loaded The silverware basket can be doubled see fig B so that only one section may be used when the silverware load is light This also makes space for additional pots and pans and it can also be placed in the upper rack Silverware should be placed in the silverware basket with the handles at the bottom if the rack has side baskets the spoons should be located individually into the appropriate slots Espe cially long utensils should be placed in the horizontal position at the front of the upper rack How to use the upper rack The upper rack is designed to hold more delicate and lighter dishware such as glasses cups and saucers plates small bowls and shallow pans as long as they are not too dirty Position the dishes and cookware so that they do not get moved by the spray of water The upper rack can be adjusted for height by using the knobs located on the sides of the rack itself see fig C Shelf Lean tall glasses and those with long stems against the shelf not against other items to be washed Place glasses cups and small bowls on the additional cup rack The additional cup rack can be swivelled in or out as required see fig D Lower Rack Upper Rack mH HUI l VCR dame dan is oe i LEA Starting the Appliance Starting a wash cycle After having completed all of the installation steps in the preced ing paragraphs turn
14. r in the event of a problem with the water supply hose or leaks within the unit in order to prevent damage to your home If for any reason the box containing the electrical components hap pens to get damaged remove the plug for the appliance from the socket immediately In order to guarantee that the anti flood ing feature operates properly the A box with water supply hose must be attached to the water supply tap as shown in Fig 1 No other type of connection is acceptable 10 The water supply hose must not under any circumstances be cut as it contains electrical parts which are live If the length of the hose is not adequate to make a proper connection the hose must be replaced with one which is long enough This hose is available upon request from specialised retailers and service centres Drain Hose Connection Insert the drain hose into a drain pipe with a minimum diameter of 4cm or let it run into the sink making sure to avoid bending or crimping it Use the special plastic support that comes with the ap pliance see fig 3 The free end of the hose must be at a height between 40 and 100 cm and must not be immersed in water Attention The special plastic hose support must be solidly fastened to the wall to prevent the drain hose from moving and allowing water to spill outside the drain Electrical Connection After making sure that the voltage and frequency values for the current in the home correspond to thos
15. tage in rinsing dishes cookware and utensils before placing them in the dishwasher How to keep Your Dishwasher in Shape After Every Wash After every wash turn off the water supply to the appliance and leave the door slightly ajar so that moisture and odors are not trapped inside Remove the plug Before cleaning or performing maintenance always remove the plug from the socket Do not run risks No solvents or Abrasive Cleaning Products To clean the exterior and rubber parts of the dishwasher do not use solvents or abrasive cleaning products Rather use only a cloth and warm soapy water To remove spots or stains from the surface of the interior use a cloth dampened with water and a little while vinegar or cleaning product made specifically for dishwashers Cleaning and Special Maintenance Filter Assembly For best performance and results the filter assembly must be cleaned frequently The filter efficiently removes food residue from the wash water allowing it to be recirculated during the cycle For this reason it is a good idea to remove the larger food particles trapped in the filter after each wash cycle by rinsing the A semi circular filter and cup under running water To remove the filter assembly pull on the cup handle in the upward direction The entire filter as sembly made up of the A semicircular filter and the B fine filter should be cleaned at least once a month To clean the filter and the fine f
16. ut 5 seconds Once the cycle has been cancelled the dishwasher will emit a short acoustic sound and the relative indicator light will turn off To set a new wash cycle follow the instructions contained in the paragraph entitled Setting and Starting a Wash Cycle If you forget to load some of the dishes The wash cycle can be interrupted by opening the door carefully in order to avoid being sprayed by hot water When the door is closed again the cycle will automatically restart at the point where it left off At the end of the wash cycle The end of the cycle will be indicated by a double acoustical signal and the blinking of the M indicator light Open the door turn off the appliance using the ON OFF switch and turn off the water supply to the unit Wait a few minutes before removing the dishes so as to avoid handling them while still hot when they are more susceptible to breakage and to get better drying results Setting The Start Delay Time Open the door of the dishwasher partially If the C button is pressed see Close up View Control Panel The start time for the wash cycle can be delayed for 2 4 or 6 hours Each time the button is pressed the D light will come on indi cating the length of the delay After selecting the delay time the wash cycle can be set as explained in Starting a wash cycle There will be a short acous tic signal and at this point the delay period will begin to count down Duri
Download Pdf Manuals
Related Search