Greenway Home Products Bordeaux GEF28WCDO User's Manual
Contents
1. A Greenway Electric Fireplace with integrated wine cooler and storage Foyer lectrique avec cabinet a boisson et remisage Assembly Instructions Instructions d assembl e Instrucciones de asamblea Greenway Home Products TIPS FOR ASSEMBLY OF YOUR NEW MANTEL e Before you begin assembly ensure you have the complete instructions and locate the red hardware bag which contains all the hardware you need to assemble this mantel Take out all the parts and compare them to the photograph and assembly instructions Be sure you have all the parts and can identify them e A helping hand is always good assemble your mantel with an adult assistant if possible Some pieces are heavy and will need to be held by a helper Assembly time will be approximately 30 60 minutes e Locate a good Phillips head screwdriver You may also use an electric screwdriver but be careful not to strip the head of the screw by over tightening them e After you assemble your mantel if you find you have interference between the door and the hearth please see Step 10 of these installation instructions for the solution ow SZ 4 TOP 1PC BASE 1PC LEFT SIDE PANEL RIGHT SIDE PANEL LEFT SIDE PANEL aos Henk 77 03 8005 EXTERIOR 1PC EXTERIOR 1PC INTERIOR 1PC a 72 03 8009 ZZ 03 8010 ZZ 03 8011 SS lt NA LEFT BASE SHELF 1P RIGHT BASE SHELF CENTRAL PANEL 1PC X SHELF 2PCS ZZ 03 8013 ZZ 03 8007 1PC ZZ 03 8015 ZZ 03 8016 IN2. obligation of Greenway Home Products under this warranty is expressly limited to such replacement or repairs The provisions of this limited warranty shall not apply to the following 1 Accidents 2 Unauthorized repairs or alterations 3 Normal maintenance 4 Changes made to other units manufactured after this mantel was manufactured 5 Incidental damages caused by failure of the wine cooler such as inconvenience or loss of use 6 Improper installation The provisions of this limited warranty shall not apply to deterioration due to wear and exposure beyond the following limitations 1 For 180 days from the date of purchase for exterior finished surfaces Due to the properties of natural wood Greenway Home Products makes no warranty against mineraling of wood components Greenway Limited Warranty is void unless the following conditions are adhered to Warranty registration must be completed and returned to Greenway Home Products 2 All warranty repairs must be preauthorized by Greenway repair facility 3 Greenway reserves the right to inspect defective parts that have been replaced under warranty Dealer is expected to hold defective parts for 60 days 4 Only parts and accessories and other material available through Greenway Home Products are to be used in the performance of warranty service 5 Purchasers are responsible for presenting notifying their Distributor as soon a problem exists The warranty repair
3. cooler into the outlet Anti tipping device At this point you must attach the anti dipping device to your mantel and your wall This device is a safety feature that will prevent your mantel from tipping over if a weight is applied which can unbalance the unit like a child climbing onto it Once you have the 2 appliances plugged in push your mantel up against the wall and enjoy your fireplace and a glass of wine WARRANTY DO NOT RETURN THIS PRODUCT TO THE STORE Greenway Home Products is pleased to offer in home warranty repairs Please contact Customer Service at In Canada 1 866 253 0447 In the USA 1 866 282 0533 Limited Warranty Definitions Greenway Home Products Manufacturer Mantel Mantel manufactured by Greenway Home Products Purchaser Purchaser of the Mantel Distributor Facility authorized to sell Greenway Home Products Warranty Card Greenway Home Products Limited Warranty Registration Card identifying the Purchaser and product model Greenway Limited Warranty Greenway warrants to the Purchaser that the Mantel is free from defects in material and workmanship under normal use and service for 1 year 1 year limited parts from the date of purchase All warranty repairs must be preauthorized by Greenway Home Products Greenway will at its option replace or repair free of charge any defective part which the Purchaser shall notify their Distributor or Greenway Home Products within the warranty period The
4. TERIOR 1PC 77 03 8008 ZZ 03 80012 aa p FLAT HEAD SCREW FLAT HEAD SCREW 8PCS 38PCS J BACK PANEL 1PC LEFT DOOR 1PC RIGHT DOOR 1PC ZZ 03 8017 ZZ 03 8018 ANTI TIP DEVICE 2 SETS GET READY TO START Before assembly use scissors to unwrap the parts from the packaging DO NOT use a box cutter or exacto knife as you may cut into the mantel pieces inside the box and damage the finish Check for the hardware bag which is red and located inside the packaging taped to the top box Be sure you DO NOT discard any pieces Step 1 ZA Locate the hearth and place it on the floor Do not put it up a wee against the wall at this point in the assembly as you need A PE to get in behind the mantel to insert several screws ee Step 2 Locate the left and right bottom plates Standing in front of the hearth place them with the finished side up on the left and right sides of the left and right side storage compartments Step 3 Locate the left inside and left outside wall panels the back panel and the top panel for the left wine bottle storage compartment Position both the inside and outside wall panels position the back panel finished side inside the compartment by inserting the panel in the groove of one side then squeezing the sides together ensuring that the back panel stays in position within the grooves of both side panels Get your helper to hold the panels snuggly in place while you insert the 6 screws which w
5. ill hold the sides and back in position Step 4 Locate the left side top panel this part has the 5 holes in it for the wine glass storage rack and the wine glass storage rack Position the left side top panel face up and attach the rack by inserting and tightening the 5 screws remember to use the smaller screws to attach the storage rack Once you have installed the silver colored wine glass storage rack you can take the top back to the mantel and position the top panel on the sides and back Have your helper apply pressure to hold the top panel in position while you insert and tighten all 6 screws Enough pressure must be applied to avoid gaps between the top and the side panels Step 5 Locate the red wine bottle storage shelves These 2 pieces have a channel cut partway through each one Choose the two best faces and place them facing up Line up the channels so that you can insert one piece onto the other piece forming an X Once you have formed the X insert the X into the left storage compartment and ensure the X is inserted completely into the opening so there is no interference with the door Step 6 Locate the right inside and outside wall panels for the right wine cooler storage compartment Place them around the bottom panel already in place on the hearth Get your helper to hold these pieces in place while you insert and tighten the 6 bottom screws Position the top panel in place Get your helper to apply pres
6. nt the wine cooler door from interfering with the storage compartment door If you have any questions about the wine cooler please reference the installation instructions that come With the unit Please reference the Quick Tips section of that instruction manual Step 10 You are now ready to install the doors on the right and left side storage compartments Locate the left door The hinge bracket for this door is already attached to the hinge located inside the left compart ment it came installed Get your helper to hold the door in position while you insert and tighten the 2 screws in each of the hinges Repeat for the right side door You can level the doors by releasing or tightening the tension on the leveling screw on each hinge see picture for location and realigning the door so it is level from the front Leveling screws Step 11 Get your helper and locate the top of your mantel This top is very heavy It will take 2 people to lift and position it in place Ensure the top goes over the positioning guide located on the header The top must go over this guide to be positioned correctly Once the top is in place insert and tighten the 9 screws 1 _ a r a a aa oe pue Le j i S gp Sp A __ _ gt M Step 12 You are now ready to position your mantel against the wall This step requires 2 people to move the unit Once you are close to the wall plug in the firebox and the wine
7. s should be completed in a reasonable amount of time from the date of authorization Not to exceed 30 days past notification 6 It is the original purchaser s responsibility to deliver this unit along with the original proof of purchase to the nearest authorized service center Any transportation charges incurred are the responsibility of the purchaser and are not included in this warranty This limited warranty is expressly in lieu of any other expressed or implied warranty includ ing any implied warranty or merchantability or fitness for a particular purpose and of any obligations or liabilities on Greenway Home Products which neither assumes nor authorizes any other person to assume for it any other liability in connection with the Water Dispenser manufactured by it The warranty is null and void if used in commercial or industrial applications Greenway Home Products
8. sure to the side to eliminate any gaps while you insert and tighten the top 6 screws Step 7 Take your electric firebox out of its packaging and position it between the 2 storage compartments Ensure the plug is at the back of your mantel ready to be plugged in before you position your mantel in place up against the wall The tirebox does not get attached to the mantel in any way it just sits there If you have any questions about the firebox please reference the installation instructions that come with the unit Please reference the Quick Tips section of that instruction manual Step 8 Locate the header piece that will be attached to the left and right storage compartments and will sit above the firebox Position the header with the finished side facing the front of the mantel Insert and tighten the 4 screws which will hold the header in place CAUTION DO NOT USE AN ELECTRIC DRILL TO INSERT THESE SCREWS A POWER DRILL CAN DRIVE THE SCREWS THROUGH THE FACE OF THIS PANEL THIS SHOULD NOT HAPPEN WITH A MANUAL SCREW DRIVER BE CAREFUL Step 9 Take the wine cooler out of its packaging and position it in the right side storage compartment Ensure the plug is at the back of your mantel ready to be plugged in before you position your mantel in place up against the wall Ensure the feet of the wine cooler are positioned in the holes for the feet on the bottom panel of the storage compartment This positioning will preve
Download Pdf Manuals
Related Search