Graco 4113 User's Manual
Contents
1. The Entertainer Activity Center by GRACO OWNER S MANUAL Model No Serial No Dear Customer Please fill in the model and serial numbers above from the label under the tray of your new Entertainer activity center Model 4113 Congratulations on your purchase of a Graco Entertainer activity center Graco is the recognized leader in the design and manufacture of quality baby products We believe your new Graco Entertainer activity center is a wise choice promising many hours of enjoyment for your baby Before using your activity center please take a few minutes to read this Owner s Manual The short time you spend reading these instructions will help you to use your activity center properly Customer Satisfaction Our goal is to make every product the best it can be We are also committed to supporting our products after purchase If you would like to speak with Graco about your product please contact our Customer Service Department at 1 800 345 4109 Our knowledgeable staff will be ready to answer any questions you may have concerning parts use or maintenance When you call please have the model and serial numbers ready so your call may be processed quickly and efficiently 1997 Graco 281 6 97 AWARNING Failure to follow these warnings and the assembly instructions could result in serious injury or death Never leave child unattended Always keep child in view wh2. ile in this product Never lift or carry this product with Do not use product with a child who child in it can tip over or climb out of product Strings can cause strangulation DO NOT place items with a string around your child s neck such as hood strings or pacifier cords DO NOT suspend strings over the activity center or attach strings to toys Product may gradually move across To avoid tipovers place product on the floor as child plays in it Watch for flat level floor ground Adjust legs to movement of product and be sure same height so that the tray is level child stays away from hazards in the before placing child in product area such as stairs cords hot liquids pools sources of heat and anything else that may injure your child THIS PRODUCT REQUIRES ADULT ASSEMBLY READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND USE OF THIS PRODUCT If you experience any difficulties please contact the Customer Service Department KEEP INSTRUCTIONS FOR FUTURE USE THIS PRODUCT IS FOR USE ONLY by a child who is able to sit upright unassisted unable to walk weighs less than 30 pounds and is less than 32 inches tall EXCESSIVE EXPOSURE TO SUN OR HEAT could cause fading or warping of parts DO NOT USE THIS PRODUCT if it is damaged or broken THIS PRODUCT IS NOT INTENDED FOR COMMERCIAL USE 2 3 PARTS LIST CHECK that you have all the parts listed below BEFORE assembling your Entertaine
3. into the hole Then plug forked end of bar into the square hole in the tray Tighten screw until clicker does not move freely DO NOT overtighten then loosen screw slightly To Adjust the Seat Height AWARNING Do not adjust height while child is in activity center om Step 1 Press in the buttons on each leg to adjust seat to desired height The bottom edge of the upper tubes must be even with one of the three lines on the lower leg tube oS AWARNING For your child s safety all three legs must be set to the same height Tray must be level 8 Step 2 Replacement Parts After adjusting height of the seat CHECK that your child s feet can rest completely on the floor of your Instructions for ordering activity center parts activity center Tray should not be too high or too low Complete form below Your model number MUST be Remove child and readjust height if necessary included on the form to ensure proper replacement parts Your model number can be found on a sticker on the bottom of the tray Payment must accompany your order awe Parts List Price Teether toy eeeeeeccccccceeceeseceseeeenseseseeneneneeees 5 00 Beads and bar ccccccccccscseseseseseteteteteenes 5 00 Clicker and SCFEW cccceccccecteeseeeeteeeeeesees 5 00 J4 Colne tec tet acces ea 14 50 Seat ring and bearings ccceeeeeee 7 00 a Seat lock and SCrEW eccceseeseeeeteseeteeeeees 5 00 Complete
4. r activity center If any parts are missing call Customer Service at 1 800 345 4109 Tool required Screwdriver Teether Beads and bar toy Seat lock and screw CARE AND MAINTENANCE FROM TIME TO TIME CHECK YOUR ACTIVITY CENTER for loose screws worn parts torn material or stitching Replace or repair the parts as needed Use only Graco replacement parts REMOVABLE CLOTH SEAT may be machine washed in lukewarm water on delicate cycle and drip dried DO NOT MACHINE DRY NO BLEACH TO CLEAN FRAME use only household soap or detergent and warm water NO BLEACH To Assemble Your Entertainer Activity Center Step 1 Turn the tray over and locate the hole that the seat lock screws into Place the seat lock on the tray as shown and screw it to the tray DO NOT overtighten screw seat lock must be free to slide Step 2 Ie T I a l l Ya Four tabs are located eN behind the indentations inside the seat ring TS Q A Remove the seat ring by TJE pulling the four tabs out q from under the tray one at a time while lifting the seat ring Solid color inside Step 3 Put the seat ring upside down inside the cloth seat The high side of the seat ring goes to the back of the seat where the warning label is located Attach the seat to the seat ring by tucking the seat edge into the channel and snapping the grommets on the pegs Pattern side UP Step 4 Turn the seat o
5. tray unit with legs height 25 00 Tray at proper height springs and height buttons Height buttons and height springs only 5 00 Retainer rings ccceccesseseteseeeeeteeeteeeees 5 00 Spring covers with upper and lower trim 5 00 Complete base unit with legs retainer 20 00 straps boots and retainer rings Prices subject to change without notice IF YOU NEED HELP If you have any questions please call toll free 1 800 345 4109 Return the form below with payment to GRACO CHILDREN S PRODUCTS INC CUSTOMER SERVICE DEPARTMENT MAIN STREET ELVERSON PA 19520 TRAY TOO HIGH TRAY TOO LOW Coo et Cee a Model Number SHIP TO Must be filled in Name O Teether toy O Beads and bar Address O Clicker and screw O Cloth seat O Seat ring and bearings City State Zip O Seat lock and screw O Complete tray unit O Height buttons and Telephone springs O Retainer rings O Check enclosed O Spring covers payable to Graco Children s with trim Products Inc O Complete base unit j O Charge to credit card OVisa O MasterCard L Discover Total Account 1 6 sales tax l PA only Expiration date I Total amount Signature due Le Se a a Se a eS eS SS ee 281 6 97 9 10
6. ver and push the seat down into the seat ring Step 5 Snap the seat ring back onto the tray Make sure all four tabs are snapped onto the inside lip 281 6 97 5 Step 6 Turn tray over Push one leg into socket in tray exactly as shown until it snaps into place Repeat for other two legs Button faces seat Step 7 On top of tray CHECK that snaps are visible through slots Pull on leg to be sure it is securely attached Snaps visibl Step 8 Slide the leg tubes on the tray onto the leg tubes on the base as shown HINT If a tray leg tube will not slide onto the base leg tube twist the base tube slightly to line up the parts Push in the buttons on each of the upper leg tubes and adjust the activity center to the desired height The bottom edge of the upper tubes must be even with one of the three lines on the lower leg tube CHECK that all three leg tubes are set to the same height Step 9 Assemble the toys on the tray as shown NOTE Toys may be removed from tray for cleaning or storage Insert teether stalk into the tray To Use the Seat Lock Push gently on latch and turn the seat until latch engages in one of the four stop positions To allow seat to swivel again pull lock out Retaining Push beads firmly over the retaining loops on bead bar Insert end with loops into the hole directly over leg and turn bar until fully seated retaining loops do not go
Download Pdf Manuals
Related Search