Graco 3A1292C User's Manual
Contents
1. ti16522a Part 24J692 24H366 16P667 24G609 24H362 24H363 Description Lid with seals Reservoir liners 5 G2 adapter plate for use with models 16N657 16M886 16N664 16N665 16N666 16N668 16N669 16N670 Hose set velcro strap Back pack Air compressor with 9V battery Air compressor switch Hose set Drain hose Suction hose 3A1292C Before You Start Before You Start The ProPack Portable Spray Pack is shipped with a bat tery inside the air compressor which must be connected before operation 1 Remove contents from backpack including any packing materials 2 Remove air compressor from reservoir lid ti17593a 4 Remove 9V alkaline battery and remove shipping seal from battery terminals ti17825a 5 Pull battery connector out of air compressor EZ T ti17591a 3A1292C 6 Connect battery and place inside air compressor ti17595a ti17824a 8 Turn on power switch to test battery red LED light should turn on ti17596a Setup Instructions 1 Perform Pressure Relief Procedure see sprayer manual 2 Remove sprayer battery or unplug sprayer ti15504a 4 Align hose set adapter A with sprayer inlet B and insert into sprayer Thread hose set adapter ring until tight 5 Place liner optional into reservoir and fill with material ti16506a 6 Install suction tube and strainer t2. charge which charges may include the costs of parts labor and transportation THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE Graco s sole obligation and buyer s sole remedy for any breach of warranty shall be as set forth above The buyer agrees that no other remedy including but not limited to incidental or consequential damages for lost profits lost sales injury to person or property or any other incidental or consequential loss shall be available Any action for breach of warranty must be brought within two 2 years of the date of sale GRACO MAKES NO WARRANTY AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE IN CONNECTION WITH ACCESSORIES EQUIPMENT MATERIALS OR COMPONENTS SOLD BUT NOT MANUFACTURED BY GRACO These items sold but not manufactured by Graco such as electric motors switches hose etc are subject to the warranty if any of their manufacturer Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties In no event will Graco be liable for indirect incidental special or consequential damages resulting from Graco supplying equipment hereunder or the furnishing performance or use of any products or other goods sold hereto whether due to a breach of contract breach of warranty
3. AUTION System is now pressurized Failure to properly depressurize system will result in material discharging from hose and possible injury Always turn off and slowly remove air compressor from lid assembly to depressurize system before removing e Hose set from sprayer e Hose set from lid e Lid from reservoir ti16510a Clean up Power Flush This procedure is for water based architectural paints and coatings only 4 CAUTION System is pressurized Failure to properly depressur ize system will result in material discharging from hose and possible injury Always turn off and slowly remove air compressor from lid assembly to depressurize system before removing Hose set from sprayer Hose set from lid Lid from reservoir Turn air compressor switch off and slowly remove air compressor from lid assembly J ti16510a Remove suction hose and drain hose from lid assembly ti16505a Connect suction hose nut to faucet or garden hose Put the prime relief valve in the up position on the sprayer then turn on water supply and run water through system while squeezing trigger until clear water comes out end of drain hose For best results use hot water ti16513a Clean up Power Flush NOTE Be sure to aim the drain hose into a waste container when squeezing trigger to prevent spilling water and material If the drain hose is not thoroughly cleaned it can become plugged due to paint bui
4. Operation GRACO Pro Pack Portable Spray Pack 3A1292C a EN For use with Graco hand held sprayers except Fine Finish sprayers For portable spray applications of water based and oil based mineral spirit type architectural paints and coatings only Not approved for use in explosive atmosphere locations IMPORTANT SAFETY INSTRUCTIONS For complete warnings and safety instructions see sprayer manual Model 24F893 Maximum Working Pressure 12 psi 0 83 bar 0 083 MPa ti16502a FIRE AND EXPLOSION HAZARD Use only water based or oil based mineral spirit type materials with flash point greater than 100 F 38 C Do not use materials which state FLAMMABLE on the packaging For more information about your material request MSDS from distributor or retailer Use oil based material outdoors or in a well ventilated indoor area with a flow of fresh air ces PROVEN QUALITY LEADING TECHNOLOGY H003 Component Replacement Kit Identification Component Replacement Kit Identification Part 115489 24H367 125026 115099 16G375 106553 24J023 24H365 24D425 16F731 24J691 Description Hose clamp Gasket kit Grommet Washer garden hose Seal reservoir O ring packing 1 Suction tube with strainer Reservoir 1 gallon with storage lid and gasket Storage lid with seal Reservoir 1 gallon Fitting intake with o rings 11a 12 12a 12b
5. a 3 Rinse out reservoir or discard liner N ti16524a F Kaaf 4 Fill reservoir with cleaning fluid and reattach lid with suction tube and strainer Gh Cea t ti16525a 3A1292C 5 Remove drain hose from reservoir lid and aim it into a waste container I ti17159a 6 With the prime relief valve in the up position squeeze trigger and cycle fluid from suction hose T through drain hose R and into a waste con tainer _ ti16526a If the drain hose is not thoroughly cleaned it can become plugged due to paint buildup If this does occur replace hose set 7 Put the prime relief valve in the down position Spray into waste area with tip in reverse position until water comes out clear Put the prime relief valve in the up position de Qo J ti17827a 8 Remove sprayer battery or unplug sprayer Remove tip assembly from sprayer and rinse Re install tip assembly into sprayer ti17822a 9 Remove lid from reservoir Rinse out reservoir Dis assemble lid suction tube and strainer then rinse NOTE Always follow local and state regulations when disposing material tea ae a WE x oe ti16694a a I s im a M 10 Wipe away any excess material from external parts of sprayer Back Pack Strap Adjustment For best results make strap adjustments while wearing backpack with full material reservoir Backpack should fit comfort
6. ably on lower back and still allow enough free movement to easily operate equipment Shoulder Straps To tighten Pull down on shoulder straps to tighten around shoulders and back il To loosen Lift up on plastic tabs to loosen shoulder straps Clean up Non Power Flush Belt Strap Pull belt straps to tighten around waist Hose Set Strap Once backpack is comfortable and secure route hose set over shoulder and fasten velcro straps over hoses to hold them in place ti17823a 3A1292C Troubleshooting Troubleshooting Problem Cause Solution Sprayer loses prime or poor spray pat tern Low material level Incorrect priming procedure Refill reservoir and re pressurize Place back pack on floor hold sprayer at approximately chest level and prime sprayer until material just begins to fill the drain hose approximately 1ft Prime sprayer for approximately 20 seconds to ensure no air is trapped in the line Fittings not tight and leaking air No or low pressure in reservoir Turn off and slowly remove air com pressor Tighten connections on sprayer adapter hose fittings and res ervoir lid Replace 9V battery in air compressor Remove and reinstall reservoir lid Sprayer adapter not properly installed Relieve pressure remove sprayer adapter and reinstall Make sure there are no air leaks Install new hose set Missing gasket
7. e With the exception of any special extended or limited warranty published by Graco Graco will for a period of twelve months from the date of sale repair or replace any part of the equipment determined by Graco to be defective This warranty applies only when the equipment is installed operated and maintained in accordance with Graco s written recommendations This warranty does not cover and Graco shall not be liable for general wear and tear or any malfunction damage or wear caused by faulty installation misapplication abrasion corrosion inadequate or improper maintenance negligence accident tampering or substitution of non Graco component parts Nor shall Graco be liable for malfunction damage or wear caused by the incompatibility of Graco equipment with structures accessories equipment or materials not supplied by Graco or the improper design manufacture installation operation or maintenance of structures accessories equipment or materials not supplied by Graco This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claimed defect If the claimed defect is verified Graco will repair or replace free of charge any defective parts The equipment will be returned to the original purchaser transportation prepaid If inspection of the equipment does not disclose any defect in material or workmanship repairs will be made at a reasonable
8. ldup If this does occur replace hose set 4 7 Put the prime relief valve in the down position Spray into waste area with tip in reverse position until water comes out clear Put the prime relief valve in the up position and shut off water Disconnect hose sink from suction hose ZA WS D O Doa Ue IA s Aat JSS D L8 ti17827a Remove sprayer battery or unplug sprayer Remove tip assembly from sprayer and rinse Re install tip assembly into sprayer ti17822a Remove lid from reservoir Rinse out reservoir or dispose of liner Disassemble lid suction tube and strainer then rinse NOTE Always follow local and state regulations when disposing material Plans Q i UAT Wipe away any excess material from external parts of sprayer 3A1292C Clean up Non Power Flush Clean up Non Power Flush This procedure is for water based and oil based mineral spirit type paints and coatings only 4 CAUTION System is pressurized Failure to properly depressur ize system will result in material discharging from hose and possible injury Always turn off and slowly remove air compressor from lid assembly to depressurize system before removing e Hose set from sprayer e Hose set from lid e Lid from reservoir 1 Turn off and slowly remove air compressor from lid assembly ti16510a PN 7 2 Remove lid assembly Remove and clean out suc tion tube and strainer ti16527
9. o inside of lid be sure to align center of strainer with center of reser voir lid Install reservoir lid to reservoir and hand tighten Before You Start 7 Thread suction hose nut S onto lid assembly and hand tighten Insert drain hose H onto lid assembly barb and secure with clamp ti16515a 8 Install sprayer battery or plug sprayer into a properly grounded outlet 9 Place reservoir on floor install and turn on air com pressor P Hold sprayer at approximately chest level and prime sprayer until material just begins to fill the drain hose approximately 1 ft ti16504a Suction Hose Drain Hose ti16509a 3A1292C Before You Start 10 Place reservoir into backpack NOTE The air com pressor always needs to be on while the sprayer is in operation if the light is on the air compressor is on If fluid level is at half or less allow up to 2 min utes for reservoir to pressurize before initial use 11 Pull strap until reservoir is firmly secured into back pack ___ ti16521a 12 Close prime valve on sprayer ti15425a 3A1292C 13 Place backpack system on operator You are now ready to spray NOTE If the tip needs to be changed while spraying be sure to follow Pressure Relief Procedure see sprayer manual Turn air compressor off and slowly remove from lid assembly This will ensure pressure is released from reservoir before changing the tip AC
10. s Reservoir is tilted to the point of expos ing suction tube and strainer to air Power has been depleted from battery Ensure each gasket is in place see page 2 Hold reservoir in upright position and reprime ProPack Replace battery Sprayer adapter ring will not assemble to sprayer Suction tube o rings are dry or have significant paint build up Lubricate or replace o rings with Kit 106553 not shown Material coming out of tip when trying to replace exchange tip Reservoir is still pressurized Perform Pressure Relief Procedure page 3 Turn off and slowly remove air compressor from lid assembly Technical Data ProPack Spray System Maximum Working Pressure 12 psi 0 83 bar 0 083 MPa Weight 5 1 Ib 2 3 kg Storage Temperature Range 32 to 122 F 0 to 50 C Storage Humidity Range 0 to 95 relative humidity non condensing Operating Temperature Range 40 to 90 F 4 to 32 C Battery Voltage 9 VDC Alkaline Average 9V Battery Life 5 hours Dimensions ProPack in Box 11 in x 8 in x 18 in 28 cm x 20 cm x 46 cm Hose length 3A1292C 60 in 152 cm Graco Standard Warranty Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for us
11. the negligence of Graco or otherwise FOR GRACO CANADA CUSTOMERS The Parties acknowledge that they have required that the present document as well as all documents notices and legal proceedings entered into given or instituted pursuant hereto or relating directly or indirectly hereto be drawn up in English Les parties reconnaissent avoir convenu que la r daction du pr sente document sera en Anglais ainsi que tous documents avis et proc dures judiciaires ex cut s donn s ou intent s a la suite de ou en rapport directement ou indirectement avec les proc dures concern es Graco Information For the latest information about Graco products visit www graco com TO PLACE AN ORDER IN NORTH AMERICA contact your Graco distributor or call 1 800 690 2894 to identify the nearest distributor All written and visual data contained in this document reflects the latest product information available at the time of publication Graco reserves the right to make changes at any time without notice For patent information see www graco com patents Original instructions This manual contains English MM 3A1292 Graco Headquarters Minneapolis International Offices Belgium China Japan Korea GRACO INC AND SUBSIDIARIES P O BOX 1441 MINNEAPOLIS MN 55440 1441 USA Copyright 2012 Graco Inc All Graco manufacturing locations are registered to ISO 9001 www graco com Revised November 2012
Download Pdf Manuals
Related Search