Graco 308739A User's Manual
Contents
1. WARNING EQUIPMENT MISUSE HAZARD Equipment misuse can cause the equipment to rupture or malfunction and result in serious injury INSTRUCTIONS This equipment is for professional use only Read all instruction manuals tags and labels before operating the equipment Use the equipment only for its intended purpose If you are uncertain about usage call your Graco distributor Do not alter or modify this equipment Use only genuine Graco parts and accessories Check equipment daily Repair or replace worn or damaged parts immediately Do not exceed the maximum working pressure of the lowest rated system component Refer to the Technical Data on page 14 for the maximum working pressure of this equipment Use fluids and solvents which are compatible with the equipment wetted parts Refer to the Tech nical Data section of all equipment manuals Read the fluid and solvent manufacturer s warnings Do not use hoses to pull equipment Route hoses away from traffic areas sharp edges moving parts and hot surfaces Do not expose Graco hoses to temperatures above 82 C 180 F or below 40 C 40 F Wear hearing protection when operating this equipment Do not lift pressurized equipment Comply with all applicable local state and national fire electrical and safety regulations 2 308 739 A WARNING INJECTION HAZARD Spray from the gun hose leaks or ruptured components can inject fluid into your2. Remove the pump from its mounting Note the relative position of the fluid outlet S to the air inlet T See Fig 3 Unscrew the tie rod locknuts 4 from the tie rods 3 Remove the cotter pin 5 Carefully pull the displacement pump 2 off the air motor 1 Unscrew the displacement rod U from the air motor 1 Inspect the o ring 6 Refer to manual 306 981 for displacement pump service To service the air motor refer to manual 307 043 Fig 3 Lubricate the o ring 6 and check that it is in place on the displacement rod U Orient the fluid outlet S to the air inlet T as noted in step 2 under Disconnecting the Displacement Pump Position the displacement pump 2 on the tie rods 3 See Fig 3 Screw the displacement rod U into the shaft of the air motor 1 until the pin holes are aligned Install the cotter pin 5 Screw the locknuts 4 onto the tie rods 3 loosely Mount the pump and reconnect all hoses Reconnect the ground wire if it was disconnected during repair Tighten the packing nut V Fill the wet cup with Graco Throat Seal Liquid or compatible solvent Tighten the tie rod locknuts 4 evenly and torque to 20 to 27 Nem 15 to 20 ft lb Start the pump and run it at about 2 8 bar 0 28 MPa 40 psi air pressure to check that it is operating properly AN Lubricate ZX Torque to 20 to 27 Nem 15 to 20 ft lb 07197 308 739 11 Parts Part No 239 3
3. out and the pump and hoses are fully primed 7 Release the spray gun trigger and lock the trigger safety The pump should stall against pressure when you release the trigger A WARNING To reduce the risk of serious injury whenever you are instructed to relieve pressure always follow the Pressure Relief Procedure at left 8 Relieve the pressure 9 Install the spray tip in the gun Operation A WARNING Flushing the Pump A WARNING COMPONENT RUPTURE HAZARD To reduce the risk of overpressurizing FIRE AND EXPLOSION HAZARD Before flushing read the section FIRE CH ME your system which could cause component rupture and serious injury never exceed the specified maximum air input pressure to the pump see Technical Data on page 14 AND EXPLOSION HAZARD on page 4 Be sure the entire system and flushing pails are properly grounded Refer to Grounding on page 5 10 Control the pump speed and fluid pressure with the air regulator E Always use the lowest air Flush with a fluid that is compatible with the fluid you pressure necessary to get the desired results are pumping and with the wetted parts in your system Higher pressure causes premature spray tip and Check with your fluid manufacturer or supplier for pump wear recommended flushing fluids and flushing frequency Always flush the pump before fluid dries on the 11 With the pump and lines primed and with displacement rod adequate air pressure and volum
4. state and national guidelines Always wear protective eyewear gloves clothing and respirator as recommended by the fluid and solvent manufacturer 4 308 739 Installation NOTES e Reference numbers and letters in parentheses in the text refer to the callouts in the figures and drawings e Always use Genuine Graco Parts and Accessories available from your Graco distributor If you supply your own accessories be sure they are adequately sized and pressure rated to meet the system s requirements e Fig 2 is only a guide for selecting and installing system components and accessories Contact your Graco distributor for assistance in designing a system to suit your particular needs Prepare the Operator All persons who operate the equipment must be trained in the safe efficient operation of all system components as well as the proper handling of all fluids All operators must thoroughly read all instruction manuals tags and labels before operating the equipment Prepare the Site Ensure that you have an adequate compressed air supply Refer to the performance chart on page 15 to find the air consumption of your pump Keep the site clear of any obstacles or debris that could interfere with the operator s movement Have a grounded metal pail available for use when flushing the system Mounting the Pump Mount the pump A to suit the type of installation planned The pump dimensions and mounting hole
5. air Clear increase air supply both strokes supply Insufficient air pressure closed or Open clean be sure to use air clogged air valves etc filter Clogged fluid line valves etc Clear be sure to use fluid filter Packing nut is too tight Loosen see page 8 Pump operates but output is low on Held open or worn intake valve Clear service See manual downstroke 306 981 Pump operates but output is lowon Held open or worn fluid piston valve Clear service See manual upstroke or packings 306 981 Erratic or accelerated operation Exhausted fluid supply Refill purge all air from pump and fluid lines Held open or worn intake valve Clear service See manual 306 981 To determine if the fluid hose or gun is obstructed relieve the pressure and disconnect the fluid hose and place a container at the pump fluid outlet to catch any fluid Turn on the air just enough to start the pump about 1 4 to 2 8 bar 0 14 to 0 28 MPa 20 to 40 psi If the pump starts when the air is turned on the obstruction is in the fluid hose or gun 10 308 739 Service Reconnecting the Displacement Pump f Disconnecting the Displacement Pump A WARNING To reduce the risk of serious injury whenever you are instructed to relieve pressure always follow the Pressure Relief Procedure on page 8 Flush the pump if possible Stop the pump at the bottom of its stroke Relieve the pressure Disconnect the air and fluid hoses
6. all moving parts when starting or operating the pump e Before servicing the equipment follow the Pressure Relief Procedure on page 8 to prevent the equipment from starting unexpectedly 308 739 3 A WARNING FIRE AND EXPLOSION HAZARD Improper grounding poor ventilation open flames or sparks can cause a hazardous condition and result in a fire or explosion and serious injury Ground the equipment and the object being sprayed Refer to Grounding on page 5 If there is any static sparking or you feel an electric shock while using this equipment stop spray ing immediately Do not use the equipment until you identify and correct the problem Provide fresh air ventilation to avoid the buildup of flammable fumes from solvents or the fluid being sprayed Keep the spray area free of debris including solvent rags and gasoline Electrically disconnect all equipment in the spray area Extinguish all open flames or pilot lights in the spray area Do not smoke in the spray area Do not turn on or off any light switch in the spray area while operating or if fumes are present Do not operate a gasoline engine in the spray area TOXIC FLUID HAZARD Hazardous fluid or toxic fumes can cause serious injury or death if splashed in the eyes or on the skin inhaled or swallowed Know the specific hazards of the fluid you are using Store hazardous fluid in an approved container Dispose of hazardous fluid according to all local
7. body and cause extremely serious injury including the need for amputation Fluid splashed in the eyes or on the skin can also cause serious injury Fluid injected into the skin might look like just a cut but it is a serious injury Get immediate medi cal attention Do not point the gun at anyone or at any part of the body Do not put your hand or fingers over the spray tip Do not stop or deflect leaks with your hand body glove or rag Do not blow back fluid this is not an air spray system Always have the tip guard and the trigger guard on the gun when spraying Check the gun diffuser operation weekly Refer to the gun manual Be sure the gun trigger safety operates before spraying Lock the gun trigger safety when you stop spraying Follow the Pressure Relief Procedure on page 8 whenever you are instructed to relieve pres sure stop spraying clean check or service the equipment and install or clean the spray tip Tighten all fluid connections before operating the equipment Check the hoses tubes and couplings daily Replace worn damaged or loose parts immediately Permanently coupled hoses cannot be repaired replace the entire hose Use only Graco approved hoses Do not remove any spring guard that is used to help protect the hose from rupture caused by kinks or bends near the couplings MOVING PARTS HAZARD sti Moving parts such as the air motor piston can pinch or amputate your fingers e Keep clear of
8. layout are shown on page 13 If you are using a wall bracket B check that the wall is strong enough to support the weight of the equipment hoses fluid and stress caused when the pump is in operation Mount the wall bracket 1 5 m 5 ft above the floor Grounding A WARNING FIRE AND EXPLOSION HAZARD Before operating the pump ground the system as explained below Also read the section FIRE AND EXPLOSION HAZARD on page 4 e Pump Use aground wire and clamp See Fig 1 Loosen the grounding lug locknut W and washer X Insert one end of a 12 ga 1 5 mm2 minimum ground wire Y into the slot in lug Z and tighten the locknut securely Connect the other end of the wire to a true earth ground For a ground wire and clamp order Part No 237 569 02464 Fig 1 e Air and fluid hoses Use only electrically conductive hoses with 150 m 500 ft maximum combined hose length to ensure grounding continuity e Air compressor Follow manufacturer s recommendations e Spray gun or dispensing valve Connect to a properly grounded fluid hose and pump e Object being sprayed Follow your local code e Fluid supply container Follow your local code e Solvent pails used when flushing Follow your local code Use only metal pails which are conductive placed on a grounded surface Do not place the pail on a nonconductive surface such as paper or cardboard which interrupts the grounding continuity e To maint
9. 08 739 Technical Data Performance Chart KEY Fluid Outlet Pressure Black Curves Air Consumption Gray Curves A 7 bar 0 7 MPa 100 psi Air Pressure B 4 9 bar 0 49 MPa 70 psi Air Pressure C 2 8 bar 0 28 MPa 40 psi Air Pressure To find fluid outlet pressure bar MPa psi at a specific fluid flow lpm gpm and operating air pressure bar MPa psi 1 Locate desired flow along bottom of chart 2 Follow vertical line up to intersection with selected fluid outlet pressure curve black Follow left to scale to read fluid outlet pressure To find pump air consumption m3 min or scfm at a specific fluid flow lpm gpm and air pressure bar MPa psi 1 Locate desired flow along bottom of chart 2 Read vertical line up to intersection with selected air consumption curve gray Follow right to scale to read air consumption psi cycles per minute bar MPa 19 37 54 60 71 88 1500 scfm 104 10 4 m8 min 1250 A 25 87 8 7 0 70 W 20 E 1000 0 56 N 70 7 E B oc 15 a 750 A 0 42 Q 51 51 gt i 500 B 10 34 3 4 0 28 c 250 c 3 14 17 1 7 0 gpm 0 0 0 2 0 4 0 6 0 8 1 0 liters minute 0 8 1 5 2 3 3 0 3 8 FLUID FLOW TEST FLUID NO 10 WEIGHT OIL 308 739 15 The Graco Warranty and Disclaimers Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in material and workmanshi
10. 27 Series A Ref Part No No Description Qty 1 205 997 AIR MOTOR see manual 307 043 1 2 223 587 DISPLACEMENT PUMP ASSY see manual 306 981 1 3 164 722 ROD tie carbon steel 111 mm 4 375 in shoulder to shoulder 4 101 566 NUT lock 3 8 16 101 946 PIN cotter stainless steel 154 771 O RING buna N oo W W 07197 12 308 739 Dimensions air inlet fluid outlet F fluid intake a 07196 3 8 npt f 3 4 npt m Mounting Hole Layout A 111 3 mm 4 38 in diameter B 64 mm 2 5 in C 127 mm 5 0 in D 7 1 mm 0 28 in diameter Use Gasket 161 023 order separately B a C 308 739 13 Technical Data Category Data as Ratio 15 1 Maximum fluid working pressure 105 bar 10 5 MPa 1500 psi Maximum air input pressure 7 bar 0 7 MPa 100 psi Fluid flow at 60 cycles per minute 1 9 liters min 0 5 gpm Maximum pump operating temperature 82 C 180 F Wetted parts Refer to manual 306 981 Sound Pressure Levels dBa measured at 1 meter from unit Input Air Pressures at 15 cycles per minute 2 8 bar 0 28 MPa 40 psi 4 8 bar 0 48 MPa 70 psi 7 bar 0 7 MPa 100 psi 73 3 dB A 75 9 dB A 77 7 dB A Sound Power Levels dBa tested in accordance with ISO 9614 2 Input Air Pressures at 15 cycles per minute 2 8 bar 0 28 MPa 40 psi 4 8 bar 0 48 MPa 70 psi 7 bar 0 7 MPa 100 psi Monark 87 0 dB A 89 7 dB A 91 4 dB A 14 3
11. 308 739 7 Operation Pressure Relief Procedure A WARNING INJECTION HAZARD Won The system pressure must be manually relieved to prevent the system from starting or spraying accidentally Fluid under high pressure can be injected through the skin and cause serious injury To reduce the risk of an injury from injection splashing fluid or moving parts follow the Pressure Relief Procedure whenever you are instructed to relieve the pressure stop spraying check or service any of the system equipment or install or clean the spray tip 1 Lock the gun trigger safety 2 Shut off the air supply to the pump 3 Close the bleed type master air valve required in your system 4 Unlock the gun trigger safety 5 Hold a metal part of the gun firmly to the side of a grounded metal pail and trigger the gun to relieve pressure 6 Lock the gun trigger safety 7 Open the drain valve required in your system and have a container ready to catch the drainage 8 Leave the drain valve open until you are ready to spray again If you suspect that the spray tip or hose is completely clogged or that pressure has not been fully relieved after following the steps above very slowly loosen the tip guard retaining nut or hose end coupling and relieve pressure gradually then loosen it completely Then clear the tip or hose Flush the Pump Before First Use The pump is tested with lightweight oil which is left in to prote
12. INSTRUCTIONS PARTS LIST C 308 739 Rev A This manual contains important GRACO RA warnings and information First choice when READ AND KEEP IT FOR REFERENCE quality counts INSTRUCTIONS STUBBY SIZE 15 1 Ratio Monark Pump Part No 239 327 Series A K N D 105 bar 10 5 MPa 1500 psi Maximum Fluid Working Pressure oe 7 bar 0 7 MPa 100 psi Maximum Air Input Pressure Refer to page 2 for the Table of Contents 07196 GRACO INC P O BOX 1441 MINNEAPOLIS MN 55440 1441 http www graco com COPYRIGHT 1997 GRACO INC Graco Inc is registered to I S EN ISO 9001 Table of Contents Symbols WarningS 0 0 0 cece cece eee 2 Warning Symbol Installation eirio cece co cee eo de eae eee soe ee weed 5 Operation sea e sexa EAN E ENAR 8 A WARNING Troubleshooting e enori rara o a a h 10 eE E E E T E E E E TN 11 This symbol alerts you to the possibility of serious Parts daent oani noa a EE A eee E A eae has 12 injury or death if you do not follow the instructions DIMENSIONS earren a Canin artis EEE 13 Mounting Hole Layout 000 cece eee 13 Caution Symbol Technical Data 000 c cece eee 14 Warranty icc Societe ead ch ad op eae na a betes eta 16 A CAUTION G Ph Number fete see diene eatin eae cet 16 er LTO Ry This symbol alerts you to the possibility of damage to or destruction of equipment if you do not follow the corresponding instructions
13. ain proper grounding continuity when flushing or relieving pressure always hold the metal part of the spray gun firmly to the side of a grounded metal pail then trigger the gun 308 739 5 Typical Installation Fig 2 6 H m ALLII Installation KEY 00OWD gt D Lromnm lt DUZSCPFA esses Pump Wall bracket Air line lubricator Bleed type master air valve required for pump See Warning on page 7 for part number Pump air regulator Air line filter Bleed type master air valve for accessories Electrically conductive air supply hose Fluid drain valve required See Warning on page 7 for part numbers Fluid filter Electrically conductive fluid supply hose Spray gun Fluid suction hose Air line moisture trap and drain valve Pump runaway valve Ground wire required Part No 237 569 See page 5 for installation instructions M p 07198 308 739 Installation Air Line Accessories Install the following accessories in the order shown in Fig 2 using adapters as necessary System Accessories A WARNING A bleed type master air valve D and a fluid drain valve J are required in your system These a
14. ccessories help reduce the risk of serious injury including fluid injection splashing in the eyes or on the skin and injury from moving parts if you are adjusting or repairing the pump The bleed type master air valve relieves air trapped between this valve and the pump after the air is shut off Trapped air can cause the pump to cycle unexpectedly Locate the valve close to the pump Order Part No 113 333 The fluid drain valve assists in relieving fluid pres sure in the displacement pump hose and gun Triggering the gun to relieve pressure may not be sufficient Order one of the following Part No 238 635 210 657 210 658 210 659 239 018 235 992 Description 1 4 npt mbe carbon steel 1 4 npt mbe carbon steel 3 8 npt mbe carbon steel 1 4 npt x 3 8 npt mbe carbon steel 1 4 npt mbe stainless steel 1 4 npt x 3 8 npt mbe stainless steel Air and Fluid Hoses Be sure all air and fluid hoses are properly sized and pressure rated for your system Use only electrically conductive air and fluid hoses Use a 13 mm 1 2 in I D minimum air hose H to supply air to the pump Fluid hoses must have spring guards on both ends Connect a fluid hose L to the pump s 3 8 npt f fluid outlet Use of a short whip hose between the main fluid hose and the gun M allows freer gun movement Connect a fluid suction hose or tube N to the pump s 3 4 npt m fluid intake Air line lubricator C Prov
15. ct the pump parts If the fluid you are using may be contaminated by the oil flush it out with a compatible solvent before using the pump If the pump is being used to supply a circulating system allow the solvent to circulate until the pump is thoroughly flushed See Flushing the Pump on page 9 8 308 739 Packing Nut Wet Cup A WARNING To reduce the risk of serious injury whenever you are instructed to relieve pressure always follow the Pressure Relief Procedure at left Keep the packing nut wet cup V filled with Graco Throat Seal Liquid TSL or compatible solvent to help prolong the packing life Check the tightness of the packing nut weekly tighten just enough to prevent leakage do not overtighten it See Fig 3 on page 11 Relieve the pressure before adjusting the packing nut or adding TSL Starting and Adjusting the Pump Begin these steps before you install the spray tip 1 Ensure that the air regulator E and bleed type master air valve D are closed See Fig 2 on page 6 2 Connect a suction hose N to the pump s fluid inlet or lower the pump into a fluid supply container 3 Hold a metal part of the spray gun M firmly to the side of a grounded metal pail and hold the trigger open 4 Open the pump s bleed type master air valve D 5 Slowly open the air regulator E until the pump starts approximately 2 8 bar 0 28 MPa 40 psi 6 Cycle the pump slowly until all the air is pushed
16. e supplied the pump starts and stops as the spray gun is opened and closed In a circulating system the pump runs A CAUTION continuously and speeds up or slows down as supply increases or decreases until the air supply Never leave water or water base fluid in the pump is shut off overnight If you are pumping water base fluid flush with water first then with a rust inhibitor such as mineral spirits Relieve the pressure but leave the A CAUTION rust inhibitor in the pump to protect the parts from corrosion Never allow the pump to run dry of the fluid being pumped A dry pump will quickly accelerate to a high speed possibly damaging itself If your pump accel erates quickly or is running too fast stop it immedi ately and check the fluid supply If the supply con tainer is empty and air has been pumped into the lines refill the container and prime the pump and the lines with fluid or flush and leave it filled with a compatible solvent Be sure to eliminate all air from 1 Relieve the pressure the fluid system A WARNING To reduce the risk of serious injury whenever you are instructed to relieve pressure always follow the Pressure Relief Procedure on page 8 2 Remove the spray tip from the gun Shutdown and Care of the Pump 3 Hold a metal part of the gun firmly to the side of a A WARNING grounded metal pail 4 Start the pump Always use the lowest possible To red the risk of serious injury whenev
17. er you SORKETA m 4 fluid pressure when flushing are instructed to relieve pressure always follow the Pressure Relief Procedure on page 8 5 Trigger the gun For overnight shutdown relieve the pressure and 6 Flush the system until clear solvent flows from the always stop the pump at the bottom of the stroke to gun prevent the fluid from drying on the exposed displacement rod and damaging the throat packings 7 Relieve the pressure Always flush the pump before the fluid dries on the displacement rod See Flushing the Pump 308 739 9 Troubleshooting A WARNING 1 Relieve the pressure 2 Check all possible problems and solutions before disassembling pump To reduce the risk of serious injury whenever you are instructed to relieve pressure always follow the Pressure Relief Procedure on page 8 Problem Cause Solution Pump fails to operate Restricted line or inadequate air Clear increase air supply supply Insufficient air pressure closed or Open clean be sure to use air fil clogged air valves etc ter Exhausted fluid supply Refill purge all air from pump and fluid lines Damaged air motor Service air motor See manual 307 043 Dried fluid seizure of displacement Clean check or replace throat pack rod ings See manual 306 981 Always stop pump at bottom of stroke and keep wet cup filled with compatible solvent Pump operates but output is low on Restricted line or inadequate
18. ides automatic air motor lubrication Bleed type master air valve D Required in your system to relieve air trapped between it and the air motor when the valve is closed see the WARNING at left Be sure the bleed valve is easily accessible from the pump and is located downstream from the air regulator E Air regulator E Controls pump speed and outlet pressure by adjusting the air pressure to the pump Locate the regulator close to the pump but upstream from the bleed type master air valve D Pump runaway valve R Senses if the pump is running too fast and shuts off the air supply to the motor A pump which runs too fast can be seriously damaged Air line filter F Install an air line filter F and a moisture trap and drain valve P to help remove moisture and contaminants from the compressed air supply Second bleed type air valve G Isolates the air line accessories for servicing Locate upstream from all other air line accessories Fluid Line Accessories Install the following accessories in the positions shown in Fig 2 using adapters as necessary Fluid drain valve J Required in your system to relieve fluid pressure in the hose and gun see the WARNING at left Install the drain valve so that it points down and the handle points up when it is opened Fluid filter K Filters harmful particles from the fluid Spray gun M Dispenses the fluid The gun shown in Fig 2 is an airless spray gun
19. p on the date of sale by an authorized Graco distributor to the original purchaser for use With the exception of any special extended or limited warranty published by Graco Graco will for a period of twelve months from the date of sale repair or replace any part of the equipment determined by Graco to be defective This warranty applies only when the equipment is installed operated and maintained in accordance with Graco s written recommendations This warranty does not cover and Graco shall not be liable for general wear and tear or any malfunction damage or wear caused by faulty installation misapplication abrasion corrosion inadequate or improper maintenance negligence accident tampering or substitution of non Graco component parts Nor shall Graco be liable for malfunction damage or wear caused by the incompatibility of Graco equipment with structures accessories equipment or materials not supplied by Graco or the improper design manufacture installation operation or maintenance of structures accessories equipment or materials not supplied by Graco This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claimed defect If the claimed defect is verified Graco will repair or replace free of charge any defective parts The equipment will be returned to the original purchaser transportation prepaid If inspection of the equipment doe
20. roducts or other goods sold hereto whether due to a breach of contract breach of warranty the negligence of Graco or otherwise FOR GRACO CANADA CUSTOMERS The parties acknowledge that they have required that the present document as well as all documents notices and legal proceedings entered into given or instituted pursuant hereto or relating directly or indirectly hereto be drawn up in English Les parties reconnaissent avoir convenu que la r daction du pr sente document sera en Anglais ainsi que tous documents avis et proc dures judiciaires ex cut s donn s ou intent s a la suite de ou en rapport directement ou indirectement avec les procedures concern es Graco Phone Number TO PLACE AN ORDER contact your Graco distributor or call this number to identify the distributor closest to you 1 800 367 4023 Toll Free All written and visual data contained in this document reflects the latest product information available at the time of publication Graco reserves the right to make changes at any time without notice Sales Offices Minneapolis Detroit Los Angeles Foreign Offices Belgium Canada England Korea France Germany Hong Kong Japan GRACO INC P O BOX 1441 MINNEAPOLIS MN 55440 1441 http www graco com PRINTED IN U S A 308 739 September 1997 16 308 739
21. s not disclose any defect in material or workmanship repairs will be made at a reasonable charge which charges may include the costs of parts labor and transportation THIS WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTIES EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE Graco s sole obligation and buyer s sole remedy for any breach of warranty shall be as set forth above The buyer agrees that no other remedy including but not limited to incidental or consequential damages for lost profits lost sales injury to person or property or any other incidental or consequential loss shall be available Any action for breach of warranty must be brought within two 2 years of the date of sale GRACO MAKES NO WARRANTY AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE IN CONNECTION WITH ACCESSORIES EQUIPMENT MATERIALS OR COMPONENTS SOLD BUT NOT MANUFACTURED BY GRACO These items sold but not manufactured by Graco such as electric motors switches hose etc are subject to the warranty if any of their manufacturer Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties In no event will Graco be liable for indirect incidental special or consequential damages resulting from Graco supplying equipment hereunder or the furnishing performance or use of any p
Download Pdf Manuals
Related Search