Graco 1466 User's Manual
Contents
1. Step 2 Pull the crotch strap and both ends of the seat belt through the slots in the seat cover Step 3 Push the elastic loop through the hole on one side of seat Step 4 Fold cover around bottom of seat Then fasten the hook into the elastic loop on one side as shown Repeat on other side CAUTION Be sure the seat cover at armrest does not interfere with tray latching 10 Using the Head Supports on certain models To provide head support for a smaller child your swing model may include one of the following accessories Two head supports Insert them into the pockets in the back of the cloth seat pad Head support cushion Use it in the seat as shown threading the seat belt straps through the corresponding holes in the cushion Using the Tray If tray does not latch check back brace to be sure the word REAR is away from the seat Step 1 Unlatch the tray by squeezing the two latches under the tray at the same time and lift up Be careful not to let the tray hit your baby when lifting or closing the tray Step 2 To latch tray push it down firmly AWARNING Tray must be latched at all times when baby is in swing Pull up on tray to be sure it is latched Reclining Back Four Positions Pull adjustment wire upward and pull seat backward to recline seat Extra pressure is required to go from the third position to full recline For upright position simply lift back2. Never recharge a battery of one type ina recharger made for a battery of another type Discard leaky batteries immediately Leaky batteries can cause skin burns or other personal injury When discarding batteries be sure to dispose of them in the proper manner according to your state and local regulations Always remove batteries if the swing is not going to be used for a month or more Batteries left in the unit may leak and cause damage Recommended Type Batteries Size D e Rechargeables Use and recharge according to manufacturer s instructions e Disposables Alkaline e NEVER mix battery types Indicator lights blink yellow when batteries are becoming weak Change batteries when swing ceases to operate satisfactorily Caring for Your Battery Powered Swing Problem Possible Reasons for Problem Swing 1 No batteries in swing won t 2 Batteries dead operat 3 Speed setting too low 4 Batteries in backwards check and 5 Corrosion on battery terminals Rotate batteries in place against terminals or clean with sandpaper or steel wool if corrosion is severe 6 Baby leaning too far forward 7 Baby grabbing swing legs Discontinue use 8 Seat not pushed high enough for a good start 9 Protective device activated Turn off motor wait 3 minutes then restart swing Seat 1 Control setting too low doesnt 2 Blanket hanging down causing increased wind Swing resistance very B
3. and even take favorites along Look for other toys in the enclosed leaflet Step 1 To install a toy insert the two prongs on the toy base into a toy mount at the notches Step 2 Turn toy base one quarter turn until you feel the toy snap into place CY Toy is removable turn it the other way with a little pressure so that you can replace it with other toys when desired Check that toy is firmly inserted by pulling on the toy If you choose not to use the toys at this time please insert the two plastic covers as described below to fill the holes in the tray To Install Covers To insert a cover into the tray of your swing first push one side into a notch then push in the other side To Remove Covers A WARNING Remove child from swing before removing covers With the aid of a flat head screwdriver carefully pry up one edge of a cover until it comes off A WARNING Throw the covers away immediately they are not reusable 152 12 99 182481 9 Attaching the Seat Belt Step 1 Thread one end of the seat belt through the belt retainer as shown Step 2 Thread both ends of seat belt through the buckles as shown CHECK that the belt is threaded correctly by pulling on the seat belt The belt should not slip through the buckle To release push in on front of buckle Attaching the Seat Cover Step 1 Slide the pocket of the seat cover over the top of the seat as shown
4. indication of the time remaining The light will blink continuously when a minute or less of time is remaining If you do not set the timer at all your swing will run until you turn it off To cancel timer mode press and hold the timer button until the light stops blinking If you are using the timer both the swing and the music will stop when the time runs out For example if the center light is red and it s blinking two times quickly between pauses your swing is on speed 5 and will run for twenty minutes before stopping To add time push the time button once or twice To turn swing off press and hold either speed button briefly To Use Music If you want music for your baby push the music button until desired volume is reached e Push once for high volume e Push a second time for medium volume e Push a third time for low volume e Push a fourth time to turn music off The music control is independent of the speed and timer settings You can have any combination of speed timer and music settings 14 FOR SAFE BATTERY USE Keep the batteries out of children s reach Any battery may leak battery acid if mixed with a different battery type if inserted incorrectly put in backwards or if all batteries are not replaced or recharged at the same time Any battery may leak battery acid or explode if disposed of in fire or an attempt is made to charge a battery not intended to be recharged
5. of seat forward 11 Installing the Batteries Step 1 With baby out of swing Coin open the battery compartment slot lid by inserting a coin penny nickel or dime into the coin slot After the lid pops open swing it down and remove it Step 2 Insert four D cells CHECK that the batteries are put in correctly Your swing will not run if the batteries are put in backwards Step 3 To replace lid put the two tabs of the lid into the two slots in the bottom of the motor housing Swing lid up and press it into place until you hear the latch click Using the Swing CHECK that all parts are securely fastened together before using the swing Step 1 Open tray and seat belt Place baby in the seat Step 2 Fasten the seat belt Adjust belt as needed to get a snug fit around your child Step 3 Close the tray CHECK that the tray is latched by pulling up on the tray AWARNING Do not depend on the tray or seat belt alone to hold your baby Always secure your baby with both the seat belt and tray when your child is in the swing 12 Operating the Six Speed Swing Your swing has six speed settings The LOW button controls the three low range speeds and the HIGH button controls the three high range speeds The lights indicate what speed is activated The green lights indicate the three low range speeds and the red lights indicate the three high range speeds Fo
6. Feet Step 1 Identify the front and rear base tubes from pictures below The feet to use with each tube can be identified by the text FRONT BOTTOM or REAR BOTTOM printed on them j Front base 9 l tube Front foot Rear base tube Rear foot 152 12 99 1S2480 5 Step 2 Begin by inserting a screw all the way into the small hole on one foot Position the foot as shown at right so the text and viewing hole are not on the short side of tube near the wire end Then use viewing Short side hole to line up the end of the of tube screw with the hole in the tube Tighten the screw securely Repeat above steps for the other feet CHECK that feet are secure by wiggling the feet Wire end Text and viewing hole Step 3 Push a plastic tip onto all four of the feet Tap leg tips on the floor to be sure they are completely on The hole in the plastic tip permits future tightening of the screw if needed Attaching the Base Tubes Step 1 Push the legs firmly onto the rear base tube exactly as shown Bracket hole points toward side of motor PUS housing a Motor Push the other two legs onto housing the front base tube switch side CHECK that all tubes are securely attached CHECK that the parts of the frame are assembled in the positions shown Straight rear base tube Bent front base tube Attaching the Hanger Tubes and Seat Step 1 Move seat back fully for
7. GRACO Open Top Swing OWNER S MANUAL Model No Serial No Dear Customer Please fill in the model and serial numbers above from the label inside the battery compartment of your new swing Model Nos 1464 amp 1466 Congratulations on your purchase of a Graco swing Graco is the recognized leader in the design and manufacture of quality baby swings We believe your new Graco swing is a wise choice promising many hours of enjoyment for your baby Before using your swing please take a few minutes to read this Owner s Manual The short time you spend reading these instructions will help you use your swing properly Please save your Owner s Manual for future use Customer Satisfaction Our goal is to make every product the best it can be We are also committed to supporting our products after purchase If you would like to speak to Graco about your product please contact our Customer Service Department at 1 800 345 4109 or visit our Internet website www gracobaby com Our knowledgeable staff will be ready to answer any questions you may have concerning parts use or maintenance When you call please have the model and serial numbers ready so your call may be processed quickly and efficiently 1999 Graco 152 12 99 1S2480 A WAR Failure to follow these warnings could result in serio Never leave child unattended Always keep your child in view strings can cause st
8. If any parts are missing call Customer Service at 1 800 345 4109 or visit our Internet website www gracobaby com Tool required Screwdriver Seat cover Plastic seat with crotch strap lt 2 Hanger Seat belt tube 2 C lt f Tray Adjustment ais C2 Back brace Toy mount cover 2 Motor Bous Pivot housing Toy 2 Aa may vary Kaaa screw ig C S Large front Smallrear Plastic aa foot 2 foot 2 leg tip 4 Front base tube Rear base tube Head support cushion on certain models Attaching the Legs Step 1 The four legs have a double button at one end and a single button beneath it With the hub sides facing up place the motor housing and pivot housing on the floor Position legs so their single buttons also face up Hub Double Pa button p Single 7 button Insert legs into the motor housing and pivot housing as shown The double buttons must fit into the channels inside the housings Step 2 Push each leg in until the double button snaps into the hole at the end of the channel Then swing the legs outward until the single button snaps into its notch as shown CHECK that the legs are properly attached by twisting them in the housings They should resist twisting If a leg twists and buttons come out of their holes insert leg into the housing again Be sure to align BOTH double buttons with BOTH sets of channels inside the housings Attaching the
9. PA 19520 On certain models l Model Number SHIP TO Must be filled in Name O Plastic seat with strap amp buckle CJ Cloth seat cover Address O Hanger tube LJ Seat belt O Tray City State Zip O Adjustment wire O Back brace C O Hardware Telephone I I I I l I I I I l l O Motor housing I O Pivot housing Io Large front foot 2 O Small rear foot 2 I O Front base tube I O Rear base tube O Leg I I I I I I O Check enclosed payable to Graco Children s Products Inc O Head support cushion Q Charge to credit card O Visa Total MasterCard Shipping O Discover amp handling 5 00 6 sales tax Account PA only I Total amount Expiration date I due Sianatare l Outside the continental U S please oy es ks o TEPNU COS E e a 16
10. atteries too weak high O A O Baby leaning too far forward Baby too heavy or too active Discontinue use 6 Soft carpet Swings higher on hard floors If you still have problems call our toll free number 1 800 345 4109 15 Replacement Parts Instructions for ordering swing parts Complete form below Your swing model number MUST be included on the form to ensure proper replacement parts Your model number can be found on a sticker beneath the swing motor Payment must accompany your order Parts List Price Plastic seat 21 00 with strap amp buckle Cloth seat cover 14 00 Hanger tube each 13 00 Seat belt c ee 5 00 LLV A 13 00 Adjustment wire 7 00 Back brace oaii 7 00 Hardware ou 5 00 Motor housing 5 25 00 Pivot housing 60 10 00 Large front foot 2 5 00 Small rear foot 2 5 00 Front base tube 7 00 Rear base tube 10 00 Leg each ou eee 7 00 Head support cushion ane 00 Prices subject to change without notice IF YOU NEED HELP If you have any questions or if you need any part not listed please call toll free 1 800 345 4109 or visit our Internet website www gracobaby com Return the form below with payment to GRACO CHILDREN S PRODUCTS INC CUSTOMER SERVICE DEPARTMENT P O BOX 100 MAIN STREET ELVERSON
11. lation This equipment generates uses and can radiate frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guar antee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help 152 12 99 152481 13 To Turn Off the Swing Press and hold either speed button Indicator light will go off and swing will stop Using the Timer You can program your swing to turn off after a certain period of time The timer button located between the two speed buttons sets the swing time in ten minute increments up to 40 minutes Push the button once the swing will run for ten minutes To add time push the timer button once more for every ten minutes you wish to add The active speed setting light will blink in repetition one blink for every ten minutes programmed The number of blinks will decrease to give you an
12. r exam ple if the far right light is green speed 3 is activated Indicator lights HIGH button LOW button controls three controls three high range low range 5 speeds speeds a an TIMER button sets swing time in ten minute increments MUSIC button turns music on and controls volume Push the LOW button once for speed 1 twice for speed 2 or three times for speed 3 Push the HIGH button once for speed 4 twice for speed 5 or three times for speed 6 To go from speed 2 to speed 3 just push the LOW button once It is not necessary to start at lowest soeed and move up The swing can begin directly at speed 5 for example by pushing the HIGH button two times Or it can go from speed 6 to speed 2 by pushing the LOW button twice After choosing speed start swing by giving it a gentle push Observe swinging motion for a minute It takes time for the swing to adjust to a setting Change setting as needed Your seat may be stopped at any time the motor is running without damaging the motor Push swing to restart If your swing motor stops operating by itself a protective device may have been activated Turn off motor wait three minutes then restart swing This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a resi dential instal
13. rangulation STRANGULATIO DO NOT place items with a string DO NOT place s around your child s neck such location where th as hood strings or pacifier cords such as window DO NOT suspend strings over the drapes phone cc swing or attach strings to toys THIS PRODUCT REQUIRES ADULT ASSEMBLY FOLLOW ASSEMBLY INSTRUCTIONS CAREFULLY If you experience any difficulties please contact the Customer Service Department DO NOT USE SWING without the seat cover DISCONTINUE USING YOUR SWING should it become damaged or broken RNING ys and the assembly instructions ious injury or death Avoid serious injury from falling or sliding out Always use seat belt TION HAZARD e swing in any e there are cords ow blind cords e cords etc DO NOT use if child weighs over 25 pounds 11 kg or becomes too active to safely use the swing CARE AND MAINTENANCE FROM TIME TO TIME CHECK YOUR SWING for loose screws worn parts torn material or stitching Replace or repair the parts as needed Use only Graco replacement parts REMOVABLE CLOTH SEAT COVER on certain models may be machine washed in lukewarm water on delicate cycle and drip dried NO BLEACH TO CLEAN SWING FRAME use only household soap or detergent and warm water NO BLEACH EXCESSIVE EXPOSURE TO SUN OR HEAT could cause fading or warping of parts PARTS LIST CHECK that you have all the parts listed below BEFORE assembling your swing
14. ward onto seat armrests The seat back must overlap the armrests Seat back Step 2 Slide hanger tubes into armrests of seat as shown Step 3 Insert two pin screws through seat armrests into the holes in the hanger tubes and tighten securely Step 4 Insert the hanger tubes into the hubs as shown Metal buttons should pop out and lock upon full insertion CHECK that the hanger tubes are secure in hubs by pulling firmly on them Attaching the Back Brace Working behind the seat snap the four pins in the ends of the plastic back brace into the holes in the hanger tubes The word REAR should be facing you Slide adjustment wire through openings in seat back then insert ends into back brace holes as shown Be sure the back brace is securely attached by pulling on it Attaching the Tray Place one hand on the armrest and slide the tray onto the hanger tube with other hand Push sleeve of tray all the way into the armrest of seat until you hear it snap Sleeve on tray must snap completely into armrest Pull firmly on tray to be sure it is securely attached Push sleeve all the way into armrest Mix N Move Toy System Your swing is equipped with two toys in Graco s Mix N Move interchangeable toy system This system featured on various Graco swings highchairs strollers and mobile entertainers allows your baby to enjoy a changing array of amusements
Download Pdf Manuals
Related Search