GN Netcom Jabra BT250v User's Manual
Contents
1. 2 Press phone s send key Using voice activated dialing after you ve set up voice tags on your phone 1 Press and release D once You ll hear 1 short beep while doing this 2 You ll then hear the voice activation tone say the name of the person you wish to call NOTE Record voice tag from headset for better reception 9 Ending a call e Press and release D once OR e End call from phone s keypad mM Answering a call e After you hear the ring tone press and release 6 once OR e Answer the call with your phone s keypad You may then need to transfer the call to the headset by pressing and releasing 0 once depending on your phone 11 Call waiting e Recommended Use standard method from your phone s keypad which typically involves pressing the send button OR e Press and release f once to answer the incoming call and toggle between calls some phones do not support this headset feature IMPORTANT Do not hold the D button down too long when making ending or answering a call This should only be a quick tap so you don t put the headset into pairing mode by accident See Enhanced features section for alternative call waiting instructions for phones that support the hands free profile TIPS AND SOLUTIONS 12 Resetting the headset If the headset is not responding or the blue light will not turn on or off after pairing you may need to RESET your headset 1 Fully insert the2. Set your Bluetooth phone to discover the headset by following your phone s instruction guide Typically the steps involve going to a setup connect or Bluetooth menu on your phone and then selecting the option to discover a Bluetooth device Your phone will find the Jabra BT250v headset and ask if you want to pair with it Confirm this by pressing yes or ok Enter passkey or PIN 0000 4 zeros then press yes or ok Fig 6 Phone specific pairing instructions and the most current list of phones with hands free profile can be found online at www jabra com fscs IMPORTANT If pairing was successful the blue indicator light will briefly flash rapidly before going back to flashing every 3 seconds If unsuccessful the light remains solid and you ll need to reattempt pairing see steps 3 5 above 11 Once you re done pairing the following new headset features will be available Last number redial when not on a call While the headset is on press and hold D until you hear 2 short beeps release immediately Rejecting an incoming call when not on a call When your phone rings press and hold D until you hear 2 short beeps release immediately Call waiting swapping between 2 calls When your phone notifies you of another incoming call while you re on a call press and hold P until you hear 2 short beeps release immediately Putting a call on hold
3. starts e Up to 200 hours of standby time B Turning on off call alert vibrate 3 flashes every 3 beeps every 30 seconds Low Battery in active mode second e 3 5 minutes of talk time left The Jabra 250v has a unique call alert feature that vibrates to inform you that you are 3 flashes every 3 beeps every 5 minutes Low Battery in standby mode receiving a call The vibrate function is enabled when you first turn on the Jabra 250v 3 seconds 3 5 minutes of talk time left If you turn on the headset in the usual way without touching the volume button the vibrate function will remain enabled Depending on phone type and usage IMPORTANT Do not hold the D button down for more than 3 to 5 seconds when turning the headset on or else it may go into pairing mode and the blue indicator light will turn solid If that happens turn off the headset wait 3 to 5 seconds and repeat process for turning the headset on oosing wearing preference Jabra BT250v is ready to wear on the right ear If you prefer the left gently rotate the MiniGel 180 For optimal performance wear Jabra BT250v and your Bluetooth phone on the same side of your body In general you will get better performance when there are no obstructions including parts of your body between the headset and the phone Fig 4 B Making a call If Jabra BT250v is off turn it on now see Turning headset on off section Using phone s keypad 1 Dial number on keypad
4. Jabra BT 250v User manual Bluetooth Headset English rss 3 A nn 49 920 nsss 65 a a oF Bahasa Melayu 97 PART NUMBER 82 00383 English 1 Checkiphone compatibility ccsciawercasawes ne 4 2 Charge Jabra Bl 250V 93 nun anne an 4 3 Read the glossary sauna 5 4 Pair to your Bluetooth phone cc secs eee eee e rene eee eee 6 5 Turning on off call alert vibrate 0 cee cece eee e eee seen 6 6 Turning headset on off s 0 nn 7 7 Choosing wearing preference u ssssseeseneeneeennenenennenen nennen 8 8 Makinga call ccc nisse E E E N haus 8 9 Endinga callie andern 9 10 AnsWwering itall u r essen nennen mn ee 9 1l Call waiting u ei een 9 12 Resetting the headsets cn anna 10 13 Tips for Nokia Bluetooth phones ccecee tense e ee eeae ennen 10 14 Enhanced features for Bluetooth phones with hands free profiles 10 15 Frequently asked questions 2 ccce cece ee eenee eet enneeeeennaes 12 16 Needim rshelpfu s5u ensiinene EE 13 17s Storage of headset ns anA E REEE enemas 14 18 Certification and safety approvals cece En sand eee enee eee eens 14 19 Warranty and parts replacement cccee sees essen nennen 14 20 GLOSSARY ec cra accatvasrare a Bene nme Renee 16 Jabra BT250v Overview Blue Indicator Light Multi Function Button D Volume Control Button Chargin
5. Jabra BT250v headset and ask if you want to pair with it Confirm this by pressing yes or ok Turning Press and hold 0 for 3 to Ascending The blue indicator headset on 5 seconds until you see a low to high light will flash while burst of flashes on the blue tones the power is on see indicator light then release Status indicators table below Turning Press and hold 0 for 3 to Descending The blue indicator headset off 5 seconds until you see a high to low light will stop burst of flashes on the blue tones flashing indicator light then release pn Enter passkey or PIN4 0000 4 zeros then press yes or ok P y i a i Status indicators IMPORTANT If pairing was successful the blue indicator light will briefly flash rapidly before going back to flashing every 3 seconds If unsuccessful the light remains solid EN MM natyouhear BEES and you ll need to reattempt pairing see steps 3 5 above Flashes every Quick series of 2 tones Active Mode second low to high pitch when e Callin progress If you have a Bluetooth phone that supports the hands free Bluetooth profile active mode starts e Up to 7 hours of talk time see Enhanced features section for alternative pairing instructions Phone Flashes every Quick series of 2 tones Standby Mode specific pairing instructions can be found online at www jabra com fscs 3 seconds high to low pitch when e Waiting for call standby mode
6. While you re on a call press and hold D until you hear 2 short beeps release immediately Repeat to retrieve the call B Frequently asked questions 1 How far away from my phone will my Jabra BT250v work The operating range is typically up to 33 feet 10 metres 2 Will Jabra BT250v work with my cordless phone at home Jabra BT250v is not designed for use with cordless phones 3 Will Jabra BT250v work with laptops PCs and PDAs Jabra BT250v will work with devices that are compliant with Bluetooth version 1 1 or higher specifications and support the headset and or hands free profile s 4 Will anything cause interference with my conversation when I m using my Jabra BT250v Appliances such as cordless phones and wireless networking equipment may cause interference with your conversation usually adding a crackling noise To reduce any interference keep the headset away from other devices that use or produce radio waves 5 Will my Jabra BT250v interfere with my car s electronics radio or computer Jabra BT250v produces significantly less power than a typical mobile phone It also only emits signals that are in compliance with the international Bluetooth standard Therefore you should not expect any interference with standard consumer grade electronics equipment 6 Can other Bluetooth phone users hear my conversation When you pair your headset to your Bluetooth phone you are creating a private link between only these two Blu
7. curred in shipping Any repair work on Jabra GN Netcom products by unauthorized third parties voids any warranty 15 2004 GN Netcom A S All rights reserved Jabra is a registered Bluetooth trademark wholly owned by GN Netcom Inc and MiniGels is a trademark of GN Netcom Inc in the USA and these trademarks may be registered in other countries US and foreign patents pending Design and specifications subject to change without notice The Bluetooth word mark and logos are owned by the Bluetooth SIG Inc and any use of such marks by the companies in the GN Netcom Group is under license www jabra com RELEASE YOUR JABRA J ad b ra
8. ertification and safety approvals This product is CE marked according to the provisions of the R amp TTE Directive 99 5 EC Hereby GN Netcom declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC For further information please consult http www gnnetcom com Please note that this product uses radio frequency bands not harmonised within EU Within the EU this product is intended to be used in Austria Belgium Denmark Finland France Germany Greece Ireland Italy Luxembourg The Netherlands Portugal Spain Sweden United Kingdom and within EFTA in Iceland Norway and Switzerland Users are not permitted to make changes or modify the device in any way Changes or modifications not expressly approved by Jabra GN Netcom will void the user s authority to operate the equipment Bluetooth The Bluetooth word mark and logos are owned by the Bluetooth SIG Inc and any use of such marks by GN Netcom is under license Other trademarks and trade names are those of their respective owners 19 Warranty and parts replacement Jabra GN Netcom warrants this product against all defects in material and workmanship for a period of two years from the date of original purchase The conditions of this warranty and our responsibilities under this warranty are as follows The warranty is limited to the original purchaser A copy of your receipt or other proo
9. etooth devices The wireless Bluetooth technology used in your headset is not easily monitored by third parties because Bluetooth wireless signals are significantly lower in radio frequency power than those produced by a typical mobile phone 7 What material is the headset made of The MiniGel is made of PVC polyvinyl chloride a form of plastic The headset itself is primarily made of thermoplastic polyurethane which is a soft plastic The face of the headset where the buttons are located is made of polycarbonate a very strong hard plastic Neither the MiniGel nor the headset contains latex 8 How do I take care of Jabra BT250v e To clean the headset use a clean soft cloth that is slightly damp e To clean the MiniGel remove it from the headset by gently lifting and pulling it off the speaker housing Then wash it in warm soapy water 16 Need more help 1 Web www jabra com fscs for the latest support info and online User Manuals 2 E mail and telephone support See back inside cover for customer service support telephone numbers and e mail Storage of headset 1 Always store the Jabra BT250v with power off and safely protected 2 Avoid storage at high temperatures above 60 C 134 F such as in a hot vehicle or in direct sunlight Storage at high temperatures can degrade performance and reduce battery life 3 Do not expose the headset or any of its supplied parts to rain or other liquids 18 C
10. f of purchase is required Without proof of purchase your warranty is defined as beginning on the date of manufacture as labelled on the product The warranty is void if the serial number date code label or product label is removed or if the product has been subject to physical abuse improper installation modification or repair by unauthorized third parties The responsibility of Jabra GN Netcom products shall be limited to the repair or replacement of the product at its sole discretion Any implied warranty on Jabra GN Netcom products is limited to two years from the date of purchase on all parts including any cords and connectors Specifically exempt from any warranty are limited life consumable components subject to normal wear and tear such as microphone windscreens ear cushions decorative finishes batteries and other accessories Jabra GN Netcom is not liable for any incidental or consequential damages arising from the use or misuse of any Jabra GN Netcom product This warranty gives you specific rights and you may have other rights which vary from area to area Unless otherwise instructed in the User Manual the user may not under any circumstances attempt to perform service adjustments or repairs on this unit whether in or out of warranty It must be returned to the purchase point factory or authorized service agency for all such work Jabra GN Netcom will not assume any responsibility for any loss or damage in
11. g Cradle MiniGel m F amp F WN Jabra STOP BEFORE USING YOUR HEADSET 1 Check phone compatibility The Jabra BT250v is compatible with most Bluetooth see Glossary phones that are compliant with Bluetooth version 1 1 or higher specification and support the headset and or hands free profile s 2 Ensure that your phone has Bluetooth capability by either visiting your phone manufacturer s web site or Jabra s web site at www jabra com Jabra also provides Bluetooth headsets for most non Bluetooth phones 2 Charge Jabra BT250v Jabra BT250v uses a rechargeable battery that must be charged fully before you use the headset for the first time 1 Fully insert the headset into the charging cradle Plug the Jabra BT250v AC adaptor into the headset s charging cradle Plug the AC adaptor into the electrical outlet fe ae ai Charge your headset until the blue light on Jabra BT250v turns off The unit will be fully charged in approximately 2 hours 5 Unplug the AC adaptor from the charging cradle 6 Remove the headset from the charging cradle You are now ready to pair Jabra BT250v to your mobile phone If the headset has already been paired to your phone then you can begin using it WARNING Do not attempt to charge Jabra BT250v with anything other than the AC adaptor provided Using another AC adaptor may damage or destroy the headset IMPORTANT The blue indicator l
12. headset into the charging cradle 2 Plug the Jabra BT250v AC adaptor into the headset s charging cradle 3 Plug the AC adaptor into the electrical outlet 4 Leave the headset in the charging cradle for about 3 seconds then remove the headset see Fig 1 5 Unplug the AC adaptor from the charging cradle B Tips for Nokia Bluetooth phones Such as Nokia 6310 and 8910 series Please ensure that the headset is allowed by the phone to connect without authorization To do this you must adjust your phone settings Set the following menu options e Menu gt Bluetooth gt View Paired Devices gt select your headset press Options gt Request conn authorization No 14 Enhanced features for Bluetooth phones with hands free profiles Enhanced features are available for phones that support the hands free Bluetooth profile such as Nokia 3600 3650 6310 6310i 8910 8910i Sony Ericsson T610 T616 T618 Siemens S55 and 56 Check your phone s instruction guide or contact the phone manufacturer if you are not sure if your phone supports the hands free Bluetooth profile You can enable these enhanced features by using the following alternative pairing sequence Pairing to a Bluetooth phone with hands free profile 1 Ensure headset is off see Turning headset on off section Press and hold D plus the volume up button until you see a solid blue light approximately 8 seconds then release see Fig 5
13. ight will be on while charging and will turn off when charging is complete Removing the headset from the charging cradle while it s charging will put the headset into standby mode and stop the charging sequence IMPORTANT Jabra BT250v cannot be used while charging 3 Read the glossary Read the glossary at the end of this document to familiarize yourself with important terms used in this User Manual Once Jabra BT250v is fully charged continue with these instructions 1 To turn off the vibrate feature hold the volume down button while you turn the u sell Pair to your Bluetooth phone head eton 2 If you wish to re activate the vibrate feature hold the volume up button while you Pairing will create a unique and encrypted wireless link between turn the headset on two Bluetooth enabled devices such as your Bluetooth phone and Jabra BT250v 1 Ensure the headset is off see Turning BASIC OPERATIONS headset on off section 6 Turning headset on off What you do What you hear What you see 2 Press and hold D until you see a solid blue light approximately 8 seconds then release see Fig 2 3 Set your Bluetooth phone to discover the headset by following your phone s instruction guide Typically the steps involve going to a setup connect or Bluetooth menu on your phone and then selecting the option to discover a Bluetooth device 4 Your phone will find the
Download Pdf Manuals
Related Search