Gilson 600CM User's Manual
Contents
1. multi purpose grease Drum Shaft Tube Drum shaft lubrication can be performed by removing the 1 8 pipe plug item 4 fig3 and installing the appropriate grease fitting Greasing should be done yearly Yoke Bearing Hangers Yoke bearing hangers are located on the yoke ends and are equipped with grease fittings These bearings should be greased weekly Wheel Bearings Grease wheel bearings once per year Thoroughly remove old grease from bearings and spindle before repacking Pack bearings Y2to 2 3 full to prevent overheating Drum Tilt Brake Bearing The brake bearing casting is located near the front of the mixer and should be greased weekly Handwheel Bearing The handwheel hub bearing is located on the front of the mixer behind the handwheel This bearing should be greased weekly WARNING DO NOT GREASE BRAKE BAND OR OUTER BRAKING SURFACE OF TILT GEAR Jack Shaft Bearings Pillow block style bearings are used on the drive train counter shaft These bearings should be greased weekly Drive Chain The drive chain should be lubricated monthly with SAE 20 or SAE 30 oil Apply the oil between the side plates Engine Motor Refer to the manufacturer s engine or motor operating instructions for all maintenance and lubrication requirements and instructions LUBRICATION FREQUENCY CHART Drive 4 of 1 MIXING INSTRUCTIONS 1 Start the drum rotating 2 Add water 3 Add cement and one shovelful of2. must be bourne by the purchaser For Warranty service the product must be delivered with proof of purchase date to the dealer of original purchase or any factory authorized service dealer The delivery of the unit must be made not later than 30 days after the expiration of the warranty period EXCLUSIONS FROM WARRANTY 1 The following items are not covered under the GILSON MIXER One Year Limited Warranty and are warranted by the respective manufacturer A Engines including starters generators alternators and gear reducers Enclosed gear transmissions C Hydraulic components including pumps motors and valves D copy of the warranty and service contact information for the above items are furnished with the individual product 2 All consequential damages including pickup and delivery of the unit communication mileage charges and or rental of a replacement unit during repairs are not covered under this warranty nor is any loss of income and or other loss resulting from the failure of the product to function due to a warranty defect 3 This warranty will not apply when the product becomes inoperative due to misuse normal wear neglect improper maintenance accident or freight damage has not been operated and maintained in accordance with the instructions furnished in the Operator s Manual or has been altered or modified without approval from the factory Service Department 4 No parts or products are to be returne
3. stop the mixer and the engine instantly 4 Always have all guards and safety devices attached and in place before operating mixer Close engine housing during operation Keep inexperienced and unauthorized people away from the mixer at all times Never leave the mixer unattended while it is running 7 Shut off engine or disconnect the electric motor before making any adjustments or putting hands or tools in the drum NEVER REACH INTO THE DRUM OR PLACE TOOLS INTO THE DRUM WHILE THE MIXER IS RUNNING 8 Do not overfill the drum Do not exceed the mixer s rated capacity 9 Do not smoke while refueling the engine Shut off the engine and allow it to cool before refueling Do not spill fuel 10 Block mixer wheels when mixing 11 Use safety chains while towing mixer 12 Keep the mixer in good operating condition Loose or damaged parts are dangerous 13 Avoid loose clothing that could get caught in moving parts or on control levers KEEP HANDS AND FEET AWAY FROM MOVING PARTS 14 Do not add material to the drum while stopped Start the drum before adding material 15 Keep all warning caution and safety instruction labels in good condition Replace missing damaged or illegible labels TOWING SAFETY CHAINS For transporting the mixer slide the tow pole out as far as possible and insert the locking pin When operating the mixer slide the tow pole in and lock it in place Make sure drum is locked in posi
4. the engine manufacturer NOTICE Record the model and serial numbers of the mixer located on the nameplate in the spaces provided Engine model type and code numbers are located on the blower housing cylinder head or backplate Product Model Number Product Serial Number Engine Motor Model Number Engine Motor Code Number Purchase Date Dealer Purchased From Dealer Address Dealer Phone Number Table of Contents 1 Warranty Information 3 2 Safety Instructions Pre operational Checks 4 3 Lubrication 5 4 Care of Mixer 6 5 Batch Mix Instructions 6 6 Parts Explosions and Lists 7 HOW TO OBTAIN PARTS AND SERVICE INFORMATION For parts and service information contact either your local dealer or the Cleform Tool Corp factory CLEFORM TOOL CORP 4343 EASTON ROAD ST JOSEPH MO 64503 800 253 3676 PHONE 888 253 3676 FAX HOW TO ORDER PARTS When ordering parts be sure to indicate the following information Name of each part Complete part number Quantity of each part Model Name Include all letters and numbers Serial Number Include all letters and numbers WARRANTY This mixer is warranted to the original purchaser only to be free of defects in material and workmanship under normal use for one year from purchase date Cleform Tool Corp shall without charge repair or replace parts which are found to be defective All transportation charges for replacement parts
5. GILSON MIXERS CONCRETE MIXER MODEL 600CM GILSON MIXERS 4343 Easton Road St Joseph MO 64503 BY 816 233 4840 800 253 3676 sul Fax 816 233 4624 888 253 3676 Clefor E Mail cleform ccp com a Web Address www cleform com TO THE OWNER This owner s manual provides the information needed to operate and maintain this Gilson mixer Carefully read and follow all safety and operating instructions in this manual Also be sure every operator of this mixer reads this manual before operating the mixer The replacement of any part on this mixer by other than the manufacturer s authorized replacement part may adversely affect the performance durability or safety of the product Be sure safety precautions are observed Read and follow all safety and operating instructions in this operator s manual The manufacturer reserves the right to make changes on or add improvements to its product at any time without prior notice or obligation The manufacturer reserves the right to decide upon its sole discretion and at any time to discontinue a product Information regarding operation and maintenance of the engine can be found in a separate engine manual supplied with this mixer if the mixer is supplied with an engine The engine manual provides all the information required regarding engine adjustments Operation and maintenance Should any questions arise concerning engine operation or service contact the nearest engine repair facility or
6. coarse aggregate The coarse aggregate will break up any lumps in the cement 4 Add remaining aggregate crushed stone pit run gravel or sand 5 Mix batch for approximately one minute Drum speed should be about 25 r p m CARE OF MIXER It is important to keep the inside of the mixing drum free of hardened concrete After discharging the last batch of concrete each day add a pailful of water and two shovelfuls of gravel to the drum This will scour the inside of the drum Mix for about two minutes discharge and rinse the drum with water ar ENGINE HOUSE WHEEL amp AXLE FIGURE 1 Frame Engine Base and Tow Pole Figure 2 10 DRUM AND YOKE PARTS 19 FIGURE 3 12 DRIVE AND TILT PARTS 14
7. d to the factory without prior written approval from the factory All implied warranties including those of merchantability and fitness for a particular purpose are limited to one year from date of purchase by the original retail customer and to the extent permitted by law any and all implied warranties are excluded and disclaimed after the expiration of such period Some states do not allow limitations on how long an implied warranty lasts or the exclusion of limitations of incidental or consequential damages so the above limitations and exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state SAFETY INSTRUCTIONS SAFETY PRECAUTIONS This is the industry s safety alert symbol This symbol calls attention to items or Operations that could be dangerous This symbol can be found throughout this manual and on safety decals on the mixer Read these messages carefully The following precautions are suggested to help prevent accidents Read and practice the following precautions before operating this equipment Equipment should be operated only by those who are responsible and have been properly instructed 1 Read all operating and maintenance instructions before operating or servicing mixer Test run empty prior to actual use 2 A mixer is only as safe as its operator Give complete and undivided attention to the operation of the mixer 3 Know how to
8. tion and engine housing is closed and secured Cross the safety chains under the tow pole and fasten them to the tow vehicle fig 1 Cross Chains UNDER Tow Pole FIGURE 1 NOTE Safety chain length may need to be altered for proper connection to tow vehicle Reposition the hooks DO NOT cut chain Allow enough slack to permit proper vehicle turning while keeping chains snug enough to prevent tow pole from contacting the ground in case the hitch uncouples PRIOR TO START UP 1 Examine the mixer carefully to make sure there was no damage during shipment or since the last use Report any damage immediately to the transportation company Repair any damage before using the mixer 2 Check for free rotation of the mixer drum yoke by rotating the drum through one complete dump charge dump cycle Make sure no foreign objects or tools are in the drum before starting the motor 3 Check the engine oil Fill as required Refer to the engine manual for oil specifications 4 Fill the fuel tank with fresh clean fuel Refer to the engine manual for fuel specifications 5 Grease all fittings as called out in the lubrication specifications 6 Start the motor and check for smooth operation of the drum ring gear and pinion Note After initial 10 hours of operations check chain belts for proper tension and sprockets pulleys for alignment Check these items monthly to prevent premature wear failure LUBRICATION Use lithium based grade 2
Download Pdf Manuals
Related Search