Genesis I.C.E. 12t User's Manual
Contents
1. f absolute fidelity J Owners Manual and Set up Guide Genesis Surround ServoSub 2 12t Contents A QUICK START SET UP GUIDE 3 SAFETY TIPS 3 CONNECTIONS 3 PLACEMENT OF THE SUBWOOFER 4 ADJUSTING THE CONTROLS 4 SETTING UP THE S2 12T 5 POSITIONING AND CONNECTING THE S2 12T 5 LFE GAIN 8 LFE OUTPUT 8 POWER 8 SPEAKER LEVEL CONNECTIONS HIGH LEVEL INPUTS 9 LINE LEVEL CONNECTIONS 9 PHASE SWITCH 10 MAKING YOUR SYSTEM SOUND RIGHT 11 THE MAIN CONTROLS 12 TUNING THE SYSTEM IN 12 Low BASS 13 TUNING FOR LOW FREQUENCY EFFECTS LFE 14 THE TECHNOLOGY 15 THE SERVO ADVANTAGE 15 500W CLASS D SWITCHING AMPLIFIER 15 THE TRANSDUCERS 16 SPECIFICATIONS 17 s absolute fidelity W A Message from Genesis Congratulations You are now the owner of one of the finest sub woofers available for music and home theater systems The Genesis Surround ServoSub 2 12t is a unique subwoofer with two 12 woofers that is designed for applications requiring corner or sidewall placement and is universally installation friendly The unique shape of the S2 12t makes it an ideal partner to surround or rear loudspeakers in a multi channel music or home theater system The S2 12t is ideal in multiple subwoofer installations where the distributed bass of the system produces low bass that is more even without resonance peaks nodes and valleys anti nodes of a single source The S2 12t delivers bass frequencies as intended by the musical pe2. A useful excel spreadsheet can be found on the Stereophile Guide to Home Theater s website at www guidetohometheater com The Sweet Spot about 2 3 of the way down the page has the spreadsheet to check the acoustics of your room Adjusting the Controls Locate the spec sheet for your existing main L R loudspeakers and adjust the Low Pass frequency on the S2 12t so it matches the 3dB point of your L R speaker s frequency response If you can t find that the 3dB frequency set the S2 12t to 63Hz the 12 o clock position on the knob For speakers of general sensitivity the Bass Gain and LFE Gain can also be set at the 12 o clock position Note Should your woofer amplifier unexpectedly turn off and you are unable to turn it back on you may have overheated or over driven the amplifier It can take up to thirty minutes for the amplifier to turn back on Be patient The two most common causes for this are poor ventilation and too much amplifier gain ie the amp is being driven too hard If the amplifier is well ventilated and it still shuts down then you may have the volume control turned up too high Refer to the section on increasing the low frequency response of your speakers without turning up the volume control s absolute fidelity LAU Setting up the S2 12t While it is relatively easy to add a subwoofer into your system and hear more bass it is not as easy to integrate a subwoofer well into your system The Genesis ServoS
3. another and another and another You can even use BOTH single ended RCA and balanced XLR LFE outputs to daisy chain even more subwoofers when either the single ended input or the balanced input is used In the case of LFE using more low frequency sources not higher level is better than using less The point is not to achieve a higher level of bass response but rather by using multiple subwoofers to distribute the LFE signal around the room dramatically reducing and evening out room modes and increasing the bass capability of the system Distributing low frequency information is also helpful for reproduction of Multi channel Music because you get incredible articulation and detail in the bass all around the room Power Make sure the ServoSub 2 12t is plugged into a wall outlet that is always on The S2 12t has an auto on feature and will automatically power up from stand by when it detects a signal and will switch itself off after about 10 minutes of being idle We recommend against the use of an extension cord for providing AC power If you are forced to use an extension cord make certain that it is as heavy duty a minimum wire thickness of 12 gauge an extension cord as you can find The S2 12t running at full tilt can draw up to absolute fidelity p 1200Watts from your power supply so make sure that whatever you plug your subwoofer into can handle it Speaker level connections High Level Inputs Using a good
4. can then use a balanced interconnect to connect the output of the signal balancing device to the input of the S2 12t An added benefit of the S2 12t is that the servo amplifier incorporates an active signal balancing device This means that if your processor has only single ended outputs but you can place an S2 12t close enough to use a single ended interconnect that balanced output of that subwoofer can be used to daisy chain to the rest of the system s absolute fidelity LFE Gain The S2 12t has a control for LFE GAIN that is separate from BASS GAIN This allows you to have the S2 12t augment your surround speakers as well as deliver LFE around the room at the same time without conflicts The usual way to control the level of the LFE output is to set the LFE gain to 6 the twelve o clock position and then use the home theatre processors level control to dial in the level However different locations in the room may have different room gain in the bass frequencies The LFE gain control allows you to tune each subwoofer for optimum balance LFE Output Along with the LFE input the S2 12t has the unique capability of providing an LFE output This buffered output can be used to daisy chain the LFE signal from the S2 12t to the LFE inputs of other Genesis subwoofers including other S2 12t s S4 8 s or G928 s Thus itis possible to channel the LFE signal from your home theatre processor to one S2 12t and then from that to
5. for this application is that it has a dramatically increased efficiency especially at lower frequencies A typical Class A B amplifier is only 5096 efficient A Class D amplifier on the other hand can be 90 efficient A Class D amp also puts out more power with less heat and less power consumption ideal for use as a subwoofer amplifier The S2 12t uses a proprietary ultra efficient discrete MOSFET switching amplifier with output capability of up to a full kilowatt The design provides extraordinary control with high damping and great thermal stability so that you can play the most demanding sources continuously at high volume The Transducers The transducer used in a servo system must be strong enough to withstand the high current approach of the servo and yet delicate and light enough to react extremely quickly The S2 12t subwoofer features two 12 inch woofers that are designed with ribbed aluminum cones that are lightweight and yet inherently stiff Our aluminum cones exhibit no resonance or cone flexure anywhere near the frequencies at which the subwoofer operates The lowest break up mode where there can be any chance of distortion at all is at 6 000Hz far above the 25Hz to 120Hz frequency response of the S2 12t Therefore the driver is a perfect piston within the frequencies used and exhibits very low cone breakup distortion 16 absolute fidelity Specifications Dimensions Frequency Response Weigh
6. quality speaker cable _ connect the output of your power absolute fidelity ZA amplifier to the binding posts on the back of the S2 12t You may also connect the S2 12t to the binding posts on the back of your loudspeaker terminals if this is more convenient Make sure that you maintain proper polarity This means that the plus terminal of your amplifier must be connected to the plus red terminal on the back of the S2 12t and the negative terminal to the negative Awhite terminal Using the high level inputs to feed the 52 121 power amplifier will not degrade the sound quality of either your loudspeaker or the subwoofer Line level connections As an alternative you can use the low level inputs on the S2 12t Using a high quality interconnect cable connect your preamplifier s output to the low level inputs on the subwoofer labeled PRE AMP IN We strongly recommend that you do not use single ended interconnects longer than 10 feet 3 2 meters to connect the preamplifier outputs to your subwoofer On many preamplifiers using an interconnect that is too long will negatively affect the performance of your preamplifier because of the high capacitance of the interconnect cable across the output of your preamplifier This is why we provide balanced inputs on the S2 12t Balanced interconnects can be as long as you like See page 7 If your preamplifier has only one set of balanced out
7. subwoofer and turn up the LFE GAIN to the setting you noted down Re check the bass volume with all subwoofers on If the bass response is too high or too low use the subwoofer level setting on the processor to match the LFE volume to the volume of the rest of the speakers or do it all again using a higher or lower setting for each subwoofer 14 Bae rr Ma unnu Fa m o r z a m n s absolute fidelity wii The Technology The Servo Advantage Very few loudspeakers use servo drive either because most designers think that it is too difficult to design too expensive or because of the extraordinary demands a servo system makes on the amplifier and the transducer However the Chief Scientist of Genesis Arnie Nudell first introduced the servo system in the legendary Infinity Servo Statik One in 1968 so we know how to design and build servo systems The concept of our servo bass system is an easy one to understand It employs an accelerometer as a sensor to constantly monitor the movement of the woofer cone and instantaneously compares it to the input signal This comparison circuit identifies any deviation from the ideal and instantaneously applies a corrective signal to compensate for the deviation virtualy eliminating inherent woofer distortion As an example when you have a high impact low bass signal that starts and stops suddenly for example a kick drum the inertia of the woofer c
8. system When listening to music the full frequency range of the orchestra or rock band should be reproduced with proper dynamic range and realism from the lowest notes of a pipe organ to the whack of the timpani or the pluck of the lowest string on a Fender bass When listening to film soundtracks the same goals should be sought after so that the results are both realistic and exciting as the roar of jet planes rumble through your living room and prehistoric creatures shake the earth Fine tuning an audio or video system is an art that takes time and patience It can be one of the most rewarding learning experiences you will encounter during your pursuit and enjoyment of high fidelity music or video reproduction One of the best pieces of advice we can offer is that you take advantage of the ear s ability to identify similarities in sound This ability is useful in fine tuning your system because if every recording you listen to or every video you watch has a similarity of sound too much or too little of a certain frequency for instance then you can be fairly certain that you have yet to perfect your setup Keep at it and remember to enjoy your music and video as you work on perfecting your setup One idea that we would like to suggest is that you set the S2 12t s bass gain controls for music and use your processor to turn it up or down for home theater That way you have a subwoofer that will take care of all your needs With pr
9. the bass modes in your listening room This makes bass management easier and reduces the chance of experiencing a boomy inarticulate bass response 3 s absolute fidelity Placement of the Subwoofer One of the most common reasons to buy a subwoofer is to augment your existing loudspeakers when they do not provide enough bass for your liking In general the S2 12t is used to augment surround or rear channel speakers in a multi channel system and would be placed in a room corner closest to the surround rear channel that you are going to augment In this case you should also connect the LFE input of the 2 12t to the LFE Subwoofer output of your processor or daisy chained from the nearest Genesis subwoofer with an LFE output Since the S2 12t has speaker level inputs for left and right channels you can place a single sub against the back wall between the two rear speakers of your multi channel system If you are using a 7 1 channel system the S2 12t s dual inputs can also be connected so as to augment both surround and rear channels If you are using only one S2 12t for just the LFE channel place it in one corner of the room Try all available corners and pick the one that sounds best Note that corner placement of a subwoofer excites EVERY bass mode in your room the good the bad as well as the ugly In a very well designed room this may be the ideal placement In a badly designed room this could be a nightmare
10. 2t we realize that you are eager to hook it up and start listening Nevertheless please read this quick start guide NOW before you begin setting it up Safety Tips The S2 12t is a powered subwoofer with a built in amplifier it needs to be connected to a power socket that is always on Make sure that you are providing the correct voltage and keep the S2 12t away from water and direct heat Connections There are two common options for hooking up the S2 12t to your existing system For dedicated music systems and bass extension of surround speakers connect the high level speaker binding posts on the S2 12t to your amplifiers speaker outputs or connect them to the speaker through binding posts on the associated speaker using a short run of loudspeaker cable For traditional subwoofer use in audio video systems in multi channel home theater applications connect the line level LFE output of your processor to the LFE input on the S2A2t Our unique LFE Blend technology allows you to use the S2 12t in BOTH your music system and your home theater system at the same time by using the high level speaker inputs to augment the bass response of your surround speakers and connecting your processors LFE output to the the LFE Input You are able to blend the two signals together for better bass management of your listening room The S2 12t s LFE out can be used to daisy chain multiple Genesis subwoofers together for better control of
11. ave good deep bass a symphonic piece of music if you can or use a natural bass instrument for your guide Try to make it sound real You may have to return to the vocal track from time to time to make sure you have not gone too far in one direction If at this point the overall sound seems to be lacking in mid bass turn the low pass filter to a higher position or alternately position the main speakers closer together in order to achieve better mid bass coupling between the main speakers If the overall sound is too fat turn the low pass filter down or adjust the gain At this point we suggest you use only the low pass filter control until you get to the refinement stage Low bass If you find that there isn t enough deep bass in the overall sound of the system your first remedy is the gain control on the S2 12t amplifier This has several limitations First turned up too high it may result in some distortion on very low frequencies Secondly you may make the mid bass produced by the top of the woofer out of proportion with the mid bass produced by the bottom end of your main speakers This would make your system sound boomy in the mid bass regions A good rule of thumb is to first adjust the gain control of the subwoofer for proper mid bass response rather than low bass The theory is that if the mid bass response is correct then the low bass response should be very close to correct A good balance between proper low bass e
12. lends the low frequency effects signal from the home theatre processor into the normal input signal on the subwoofer We call this our LFE Blend technology The LFE input bypasses the internal crossover and hence uses the home theatre processor s crossover This means that the S2 12t can be used to augment the surround speakers as well as deliver the LFE channel without resorting to digital bass management on the processor On the home theatre processor set the front speakers to LARGE and sub woofer to YES Then connect the sub woofer LFE line level output from the processor to either the single ended RCA or balanced XLR LFE IN connector on the S2 12t Do not use both inputs at the same time We recommend that single ended interconnects be no longer than 10 feet 3m Hence we have provided balanced LFE inputs If your processor is further than 10 feet from the S2 12t please use a high quality balanced cable If your processor has only single ended outputs and is further than 10 feet from the S2 12t we recommend that you consider using an active or passive signal balancing device to convert the unbalanced output signal from your processor to a truly balanced signal A truly balanced signal will give you the benefit of maximum noise rejection and maximum signal fidelity over long cable runs The unbalanced interconnect which connects your preamp to the balancing device should be shorter than 4 5 feet 1 5 meters You
13. one causes the cone to be slow to begin moving Once the cone is in motion the momentum of the cone causes it to keep moving even after the output signal of the amplifier has stopped The sonic result is overhang bloat lack of tautness and definition and a blurring of dynamic impact With the servo system the circuit senses that the woofer is not moving as fast as it should and applies more current to make it move faster When the signal stops it detects that the woofer is still moving when it shouldn t and applies a counter signal to cause the the woofer to stop faster and more effectively than normal circuitry would Thus the servo drive reduces distortion and improves transient response by making the woofer seem mass less Typical non servo woofer systems have distortion levels that exceed 10 at even moderate levels The Genesis servo bass system reduces this distortion to below one percent at almost any output level Moreover it drives the woofer to constant acceleration which makes its frequency response nearly flat 500W Class D Switching Amplifier The servo system places extraordinary demands on the amplifier because it uses enormous amounts of current to make the woofer follow the signal This means that the amplifier used must deliver huge amounts of clean power 15 s absolute fidelity The best amplifier for this application is a Class D switching amplifier One of the reasons a Class D amplifier is optimum
14. oofer 5 1 channel system place one S2 12t in each rear corner of the room and connect the speaker level inputs to the nearest surround speaker thru connectors Connect the LFE input of one S2 12t to the LFE Subwoofer output of the processor and its LFE output to the LFE input of the other S2 12t Several Genesis loudspeakers and subwoofers can be daisy chained in this manner 5 1 Surround surround with two surround 010 0 52 1205 0109 Speaker Speaker Thru Thru High Level Input Processor LFE Out LFE Input Two Surround Subwoofers 7 1 System If you have a 7 1 system and two subwoofers each S2 12t can be used to augment BOTH the nearest surround as well as the rear channel via the high level inputs as well as distribute LFE to both rear corners of the room Connect the high level thru from the surround speaker to one set of high level inputs on the S2 12t and the high level thru from the rear speaker to the other 7 1 Surround with two c s sns 680 9 6 Speaker Speaker Thru Thru Speaker Thru rear surround de Speaker High Level Thru Inputs High Level Inputs Processor LFE Out LFE Input LFEThru s absolute fidelity 7 LFE Input The Low Frequency Effects LFE input allows the S2 12t to be used for augmentation of the surround speakers as well as for the LFE of your home theater system The LFE input b
15. oper setup and placement you can achieve stunning realism and musically correct and natural bass not just more bass 11 s absolute fidelity LAS The Main Controls The 52 121 subwoofer has two controls that you will use to make your system and that includes the room sound right The first is the gain control of the woofer amplifier This adjusts the volume at which the subwoofer plays The gain can be adjusted from 1 to 11 The second control is the low pass filter This adjusts the crossover frequency for the built in 12dB per octave variable crossover The crossover frequency can be adjusted from 40Hz to 138Hz where frequencies below the number set are sent to the subwoofer and frequencies above are rejected To begin adjust the low pass filter to 63Hz and set the gain control to 6 both at the 12 o clock position At this point you can turn on the woofer amplifier Tuning the system in Set up your subwoofers one at a time in conjunction with the rear or surround speaker that you are using them to augment If you are using a single subwoofer to augment two different loudspeakers adjust the subwoofer with one speaker at a time Set the low pass filter to the 3dB frequency of your main speakers and the gain control to 6 and start from there If you don t know the 3dB point of your speakers start working from a low pass filter frequency of 63Hz This will work for most small speakers We suggest that you s
16. puts and one set of unbalanced RCA type outputs choose your first preference of connection for the amplifier that is driving your loudspeaker Use the remaining set of outputs to feed the S2 12t s amplifier absolute fidelity Do not connect BOTH single ended and balanced inputs to the S2 12t at the same time You could over drive the built in amplifier and void the warranty Phase Switch There are many power amplifiers that invert the phase of the incoming signal If you have one of these and you are also using the line level inputs from your preamp you will have to invert the phase of the 2 12t Push the switch down to 180 Please note that if you have a phase inverting power amplifier and have inverted the phase on the S2 12t AND you are using both line level and speaker level inputs you must invert the phase of the speaker level inputs Connect the ve speaker lead to the ve input terminal on the S2 12t and connect the ve speaker lead to the ve input terminal 10 s absolute fidelity W ice Making your system sound right The ServoSub 2 12t subwoofer is perfect for use in 2 channel or multi channel music and video applications The setup for either is very similar and the goals should be quite the same too In our opinion the end goal of adding a high end subwoofer should be to not hear the subwoofer work but rather to add the appropriate amount of low bass that is currently missing in your
17. rformer or as intended by the movie director This is what we call absolute fidelity n this case we mean that the bass response of the speaker is completely faithful to the input signal This is achieved by servo control of the woofer cone The S2 12t plays as loudly and deeply as much larger sub woofers that cost much more and outperforms them in terms of transient fidelity and freedom from the colorations inherent in ported subwoofer designs Robert Harley puts it best in his review of the Genesis subwoofers in The Perfect Vision Transient impact was extraordinary the dynamic envelope of low frequency sounds was tight clean and articulate In addition bass extension was outstanding this woofer extended to subterranean depths and maintained its composure He went on to Say It combines first rate musicality and exceptional delicacy with a bottom end solidity and power that was fully up to the job of reproducing today s dynamic soundtracks Please read through the Owners Manual and Set up Guide to achieve the maximum enjoyment from your purchase Please write the serial number and purchase details of your Genesis S2 12t here for future reference Purchased at T EE THA a4 FM R5 EF E arnt i 23 Bs if we 4a p AM e A OZ s ADVANCED TECHNOLOGIES absolute fidelity TM A Quick Start Set up Guide Now that you have your new Genesis Surround ServoSub 2 1
18. t Inputs Outputs Controls a Finish 31 x 21 x 16 wxh xd 533mm x 787mm x 406mm 20Hz to 120Hz 1dB 16Hz to 180Hz 3dB 2dB 83 5 Ibs 38 kg High level left and right with 5 way binding posts Low level left and right single ended RCA and balanced XLR LFE low level mono single ended RCA and balanced XLR LFE low level mono buffered single ended RCA and balanced XLR Variable low pass filter Variable bass gain control Variable LFE gain control Phase switch 0 180 Basic Black or Automotive Finishes 17
19. tart with a single vocal track with instrumental accompaniment that you are very familiar with The sound of the human voice is more easily recognizable than many instruments and is the least complex sound to deal with Run a mono full range signal to the speaker that you have the S2 12t connected to the gain control of the subwoofer amplifier up or down until the voice sounds correct Concentrate on the mid bass regions as opposed to the very low bass in your recording to achieve a natural blend The voice and the music accompaniment should sound as if it were cut from one cloth not separate If the voice sounds thin or does not have enough chest to its sound turn the S2 12t s bass gain control up until it does You may also want 12 Bae rr Ma unnu Fa o r z a m n s absolute fidelity W to experiment with increasing or decreasing the low pass filter control This control will raise or lower the frequency cutoff point of the woofer If you find that the sound is thin or lacking in mid bass and that turning the gain control up to thicken the sound creates too much low bass this is a good indication that you may want to turn the low pass filter up to a higher frequency instead This will extend the response of the S2 12t into the upper bass regions without affecting the low bass level Next check the S2 12t using more than just a voice Select some music that you know to h
20. ub 2 12t makes system integration far easier than most other subs because the servo system makes the S2 12t s bass quick clean and articulate This means that no matter which main speakers you use the S2 12t will integrate well with them even fast electrostatic or magnetic planar speakers Positioning and connecting the S2 12t The S2 12t is uniquely designed to augment surround and rear channels of home theater and multi channel music systems One Surround Subwoofer If you are using one S2 12t in a 5 1 or 7 1 channel system try placing the S2 12t in either rear corner and also the center of the back wall between the rear channels Pick the location that gives you the smoothest bass response throughout the room When positioned in a corner the S2 12t will excite ALL bass modes in the room with equal energy This will generally give you the smoothest bass response in the room unless your room has just a few very strong modes Connect the high level thru from one of the surround rear speakers to one of the High Level Inputs of the S2 12t and the thru from the other surround rear speaker to the other S2 12t High Level Input Connect the LFE output of the surround processor to the LFE Input of the 2 12t 5 1 Surround surround with one surround 2 12t Speaker Thru Speaker Thru High Level Inputs Processor LFE Out LFE Input s absolute fidelity LAS Two Surround Subwoofers 5 1 System In a dual subw
21. xtension and a deep and spacious soundstage needs to be established to optimize your new speaker s performance 13 s absolute fidelity M n Tuning for Low Frequency Effects LFE The LFE input has a separate gain structure and bypasses the crossover in the subwoofer Hence it should be set up separately from the main speaker augmentation function A simple way to set up the S2 12t for LFE is to use the test and level signal available in most home theater processors and multi channel players and test discs Many DVD s include a THX calibration option that has a set of test tones for speaker level adjustment Using a high quality sound pressure meter set the LFE gain so that the S2 12t matches the volume of the main speakers If you are using multiple subwoofers you will need to set each subwoofer in turn As each location of the subwoofer may have different bass levels caused by room related gain adjust each separately To do this you first set the LFE gain on all your subwoofers to 1 fully anti clockwise Then using a LFE test tone and a sound pressure meter set the LFE gain on the first subwoofer to 3dB down for 3 subwoofers 5dB down if using 5 subwoofers from the reference volume of the main speakers Write down the setting and then turn the LFE gain back to zero Go to the next subwoofer and repeat the process until you have the LFE GAIN settings of all your subwoofers When you have all the settings go to each
Download Pdf Manuals
Related Search