GE RS Series Installation Guide
Contents
1. GE Installation Guide Lighting Lumination LED Luminaire RS Series For standard medium base sockets For GU24 pin BEFORE YOU BEGIN oe Read these instructions completely and carefully AX WARNING AVERTISSEMENT e Risk of fire or electric shock LED Retrofit Kit installation requires Risque de choc lectrique le kit d installation LED Retrofit requiert une connaissance knowledge of luminaires electrical systems If not qualified do des syst mes lectriques des luminaires Si vous n tes pas qualifi ne tentez pas not attempt installation Contact a qualified electrician linstallation Contactez un lectricien e Risk of fire or electric shock Install this kit only in the luminaires Risque d incendie ou de choc lectrique N installez ce kit que dans les luminaires qui that have the construction features and dimensions shown in ont les caract ristiques de conception et les dimensions indiqu es sur les photos et ou the photographs and or drawings sch mas Do not make or alter any open holes in an enclosure of wiring or e faites n alt rez pas les trous ouverts dans l enceinte de c blage ou composants electrical components during kit installation lectriques lors de l installation du kit e To prevent wiring damage or abrasion do not expose wiring to Pour pr venir tout risque de dommage ou abrasion n exposez pas le c blage des edges of sheet metal or other sharp objects lames m talliques ou a2. erence when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense imagination at work Prepare Electrical Wiring a Electrical Requirements Grounding Instructions The LED driver must be supplied with 95 132 VAC 50 60 Hz and rated as follows The grounding and bonding of the overall system shall be done Product nie Input Input Input Input in accordance with National Code Description Voltage Frequency Wattage current Electric Code NEC Article 600 95851 LED10RS6 827GUP 95 132V 50 60 Hz OW 0 1A 1 and local codes 95852 LED10RS6 830GUP 95 132V 50 60 Hz OW O0 1A 95853 LED10RS4 827E26P 95 132V 50 60 Hz 10W O 1A 95854 LED10RS4 830E26P 95 132V 50 60 Hz 10W 0 1A 95855 LED10RS4 827GUP 95 132V 50 60 Hz 10W O 1A 95856 LED10RS4 830GUP 95 132V 50 60 Hz 10W O 1A 85153 LED10RS6 827E26P 95 132V 50 60 Hz 10W O 1A 85160 LED10RS6 830E26P 95 132V 50 60 Hz 10W 0 1A 70120 LED13RS6 827E26P 95 132V 50 60 Hz 13W 0 15 A 70122 LED13RS6 830E26P 95 132V 50 60 Hz 13W 0 15 A 70124 LED13RS6 827GUP 95 132V 50 60 Hz 13W 0 15 A 70127 LED13RS6 830GUP 95 132V 50 60 Hz 13W 0 15 A Instal
3. lation Mounting 1 Remove lamp from the packaging TURN OFF POWER at the source to 3 Remove existing trim and bulb and check that the mounting clips the recessed housing s that you are revealing the existing socket are firmly attached installing the fixture s in Tol A GE y N 27 a aoe Ee Insert base socket adapter into O Link the socket adapter to the O Guide fixture into the housing and existing socket inside the housing matching connector clip attached gently push up until flush with the to the fixture ceiling Restore power to the lighting system GE Lighting e 1 888 MY GE LED 1 888 69 43 533 www gelighting com GE Lighting Solutions LLC is a subsidiary of the General Electric Company The GE brand logo and Lumination are trademarks of the General Electric Company 2014 GE Lighting Solutions LLC Information provided is subject to change without notice All values are design or typical values when measured under laboratory conditions IND102 052214
4. utres objets coupants ou pointus e This device is not intended for use with emergency exits Cet appareil n est pas con u pour utilisation avec sortie de secours e Min lamp compartment dimensions 15 dia x 17 h mm Dimensions minimum du compartiment des lampes 15mm diam tre x 17 h mm Save These Instructions Components Supplied Use only in the manner intended by the manufacturer e One LED retrofit If you have any questions contact the manufacturer e One installation instructions sheet The units covered in this report are intended to retrofit Type IC or non IC recessed mount Listed luminaires with instructions to remove the existing rim The minimum dimensions of luminaries are tabulated below These products are intended to be used in dry or damp locations These products are classified as to FIRE and SHOCK hazards only This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This Class B RFLD complies with the Canadian standard ICES 003 Ce DEFR de la classe B est conforme la NMB 003 du Canada Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interf
Download Pdf Manuals
Related Search