GE P54S Installation Guide
Contents
1. GE Lighting Solutions GEH 5751B INSTRUCTIONS P 154 Powerflood Floodlight READ THOROUGHLY BEFORE INSTALLING A WARNING Risk of electric shock e Turn power off before servicing see instructions AVERTISSEMENT COUPER L ALIMENTATION AVANT L INSTALLATION OU L ENTRETIEN GENERAL This luminaire is designed for outdoor lighting service and should not be used in areas of limited ventilation or in high ambient temperature enclosures Best results will be obtained if installed and maintained according to the following recommendations UNPACKING This luminaire has been properly packed so that no part should have been damaged during transit Inspect to confirm INSTALLATION A CAUTION Unit will fall if not installed properly Follow installation instructions The floodlight is provided with a trunnion bracket which can be mounted directly on flat surfaces or building fronts Mounting adaptors are available for installation on poles cross arms pipes etc The trunnion bracket has a clearance hole for a 3 4 inch bolt used for attachment of such mounting The 1 2 inch holes on either side of the 3 4 inch hole permit additional anchoring if required Tighten side trunnion bolts to 18 22 foot pounds AIMING Slightly loosen bolts A two on trunnion tilt luminaire to desired position and retighten bolts BOLT A W2. IRING Make all electrical connections in accordance with the National Electrical Code and any applicable local code requirements Verify that supply voltage is correct by comparing it to nameplate If unit is designated as multivolt or multiwatt follow specific instruction Three conductor No 14 cable with 90 C minimum insulation is recommended for making electrical connections to the P 154 After opening door loosen the 2 screws holding the reflector Remove reflector thus expos ing the terminal board Loosen screw in pressure plate insert cable through grommet and retighten screw Notice that grommet fits cable of approximately 9 16 inch diameter Grommet and pressure plate form a weather proof seal and strain relief To maintain this seal the screw in pressure plate must be retightened whenever the seal is disturbed After connections are made to the terminal board be sure insulating shield is properly placed These instructions do not purport to cover all details or variations in equipment nor to provide for every possible contingency to be met in connection with installation operation or maintenance Should further information be desired or should particular problems arise which are not covered sufficiently for the purchaser s purposes the matter should be referred to GE Lighting Solutions Connect ground lead to the green lead green ground screw on housing or terminal block provided Do not remove insulated connector
3. s e 1 888 MY GE LED e www gelightingsolutions com 1 888 69 43 533 GE Lighting Solutions is a subsidiary of the General Electric Company Evolve and other trademarks belong to GE Lighting Solutions The GE brand and logo are trademarks of the General Electric Company 2011 GE Lighting Solutions Information provided is subject to change without notice All values are design or typical values when measured under laboratory conditions 35 201578 T5 1 00
4. s from wires not needed for required voltage connection When changing voltage on reconnectable units move only the lead with the insulated connector IF SINGLE VOLTAGE All single voltage ballasts are pre wired such that user need only connect the supply conductors IF MULTIVOLT 120 208 240 277 volts Connect the ballast lead with the insulated terminal to the desired voltage terminal as indicated on the ballast terminal nameplate IF MULTIWATT Multiwatt ballasts are available in various combinations of wattage See wiring instructions on wiring tag inside the luminaire LAMPS Use only lamps specified on nameplate Observe lamp manufacturer s recommendations and restrictions on lamp operation particularly ballast type burning position etc Lamp Tightness Mogul Base Lamp The lamp should be securely inserted to the NEMA EEI specified torque of 35 inch pounds which is best achieved by very firmly tightening to insure application of sufficient torque Tightening must be sufficient to fully depress and load the center contact of the socket MAINTENANCE CAUTION Risk of burn e Allow lamp fixture to cool before handling A WARNING Risk of burn e Do not touch operating luminaire The ALZAKt finish on the reflector and the door glass may be cleaned with any suitable nonabrasive glass cleaning solution soap or detergent and rinsed with clean water GE Lighting Solution
Download Pdf Manuals
Related Search