GE JTP20 User's Manual
Contents
1. Connect the oven red lead to the branch circuit red lead in accordance with local codes using a wire nut Connect the oven black lead to the branch circuit black lead in accordance with local codes using a wire nut If the residence red black or white leads are aluminum conductors see WARNING on page 8 Install Junction Box Cover Installation Instructions Securing the Oven in the Opening Sliding the Oven Into the Drilling the Pilot Holes and Opening Mounting the Oven a Loop do not tie a 36 string around the conduit before the oven is slid into place This will keep the conduit from falling behind the oven Pull out on string loop while pushing the oven into E am the cabinet Lift oven into cabinet cutout using the oven opening as a grip Carefully push against oven front frame Do not push against outside edges As you slide the oven back pull the string so that the conduit will lie on top of the oven in a natural loop When you are sure the conduit is out of the way slide the oven 3 4 way back into the opening Remove the string by pulling on one end of the loop 10 NOTE Before drilling the pilot holes make sure the oven is pushed as far back into the opening as it will go and centered Drill through the mounting holes top and bottom of the side trim for the 8 screws provided The screws must be a minimum of 1 4 from the front of the cu2. 30 Built In Wall Oven JTP20 JTP25 JTP28 JTP48 JTP50 JT912 JT915 JT952 JT955 ZET938 ZET958 Installation Instructions If you have questions call 1 800 GE CARES or visit our website at ge com Before You Begin Read these instructions carefully and completely IM PO RTANT save these instructions for local inspector s use IMPORTANT observe all governing codes and ordinances e Note to Installer Be sure to leave these instructions with the consumer e Note to Consumer Keep these instructions for future reference Parts Included oY Bottom Trim Screws For Installation 6 Plastic Bottom Trim Optional Metal Bottom Trim Assembly on some models 31 10659 1 07 JR e Proper installation is the responsibility of the installer and product failure due to improper installation is NOT covered under warranty e NOTE This appliance must be properly grounded ATTENTION INSTALLER All electric wall ovens must be hard wired direct wired into an approved junction box A plug and receptacle is NOT permitted on these products Materials Needed a 0 0 Wire Nuts SS 36 of String Strain Relief Clamp Junction for 1 2 conduit Box Tools Needed 1 8 Drill Bit and Electric or Hand Drill et Phillips Screwdriver Installation Instructions IMPORTANT SAFETY INSTRUCTIONS For Your Safety Be sure your oven is installed properly by a qualified instal
3. Code ANSI NFPA No 70 Latest Edition You can get a copy by writing National Fire Protection Association Batterymarch Park Quincy MA 02269 Effective January 1 1996 the National Electrical Code requires that new but not existing construction utilize a four conductor connection to an electric oven When installing an electric oven in new construction a mobile home recreational vehicle or an area where local codes prohibit grounding through the neutral conductor follow the instructions in the section on NEW CONSTRUCTION AND FOUR CONDUCTOR BRANCH CIRCUIT CONNECTION You must use a three wire single phase A C 208Y 120 Volt or 240 120 Volt 60 hertz electrical system If you connect to aluminum wiring properly installed connectors approved for use with aluminum wiring must be used Installation Instructions MV Pre Installation Checklist ALL INSTALLATION INFORMATION Door removal is not a requirement for ON THE FOLLOWING PAGES IS TO installation of the product but is an BE USED FOR SINGLE AND DOUBLE added convenience To remove the door OVEN INSTALLATION Y Open the oven door as far as it will go Remove packaging materials Check behind hinges and under Push both hinge Hinge false bottom Remove labels on the locks down toward i a outside of the door plastic on trims the door rame 6 Un and panel all tape around the oven to the unlocked and any shipping screws securing osition This ma the oven to
4. e used at Junction Box Continued on following page Installation Instructions Electrical Connections cont New Construction and Four Conductor Branch Circuit Connection e When installing in new construction or When installing in a mobile home or e When installing in a recreational vehicle or e When local codes do not permit grounding through neutral a Cut the neutral white lead from the crimp Re strip the neutral white lead to expose the proper length of conductor Ground Junction Box Cover Attach the appliance grounding lead green or bare copper in accordance with local codes lf the residence grounding conductor is aluminum see WARNING on page 8 Connect the oven neutral white lead to the branch circuit neutral white or gray in accordance with local codes using a wire nut Connect the oven red lead to the branch circuit red lead and the oven black lead to the branch circuit black lead in accordance with local codes using wire nuts If the residence red black or white leads are aluminum conductors see WARNING on page 8 Install Junction Box Cover Three Conductor Branch Circuit Connection When connecting to a three conductor branch circuit if local codes permit a Connect the bare oven ground conductor with the crimped neutral white lead to the branch circuit neutral white or gray in color using a wire nut Ground and Neutral Wires Junction Box Cover
5. ews Metal Lower Trim IMPORTANT If this unit is ever removed from the cabinet or the oven is ever pulled out for service the trim must be removed first or damage to the trim will occur Pre drilling Trim on some models Make sure flat side is up on the plastic bottom trim Find the key slot on the back of the trim Key Hole Slot and Wide Flange at Top Match the key slot with the rivet on the bottom of the side trim and lower the trim onto the rivet Sy ES Lower Trim Mounting Rivet on End of Metal Lower Trim Push the trim down at both ends until it snaps securely into place N Push Trim Down at Both Ends Until it Snaps Securely Into Place A CAUTION Be sure you do not tip the oven forward during installation or you may bend the bottom trim The bottom trim provides an opening for cooling air to enter the cabinet This opening should never be blocked Installation Instructions D Replacing the Oven Door D3 Open the oven door as far as it will open NOTE The oven door is heavy You may need help lifting the door high enough to slide it into the hinge slots D4 Push the hinge locks up against the Do not lift the door by the handle front frame of the oven cavity to the locked position D1 Lift the oven door by Locked Poshlon placing one hand on each side The door is heavy so you may need help Do not lift the door by the handle Securely Fi
6. ges of cutout opening Between Inside Walls Must Be At Least 28 1 2 Wide Junction Box Location 22 to Bottom of Junction Box Height 27 1 4 Min Cabinet Width Recommended Minimum Cutout Location from Floor Cutout Depth Cutout Width Cutout Height 30 32 1 2 23 1 2 Min 28 1 2 Min 28 5 8 Max 27 1 4 Min 27 5 16 Max NOTE If the cabinet does not have a front frame and the sides are less than 3 4 thick Recommended minimum cutout location from floor 32 1 2 minimum for overlap of oven Allow a minimum of top and 114 21 for clearance to overlap of oven adjacent corners bottom of cutout drawers walls etc when door is open Cabinet Width 30 If the cabinet does not have a solid bottom two braces or runners must be installed level with the bottom of the cutout to support the weight of the oven For single ovens the runners and braces must support 150 Ibs are covered NOTE If marks blemishes or the cutout opening are visible above the installed oven it may be necessary to add wood shims under the runners and front trim until the marks or opening Suitable Bracing to Support Runners shim both sides equally to establish the cutout width 2 x 4 or equivalent runners level with bottom of cutout re 21 5 8 Over Centerline of Cabinet This oven is not approved for stackable or s
7. ide by side installation Installation Instructions Cutout for Double Built In Oven A 2 i outon Cabinet Width 30 28 1 2 Min E 28 5 8 Max Recommended Minimum Cutout Location from Floor 12 Junction Box Location Cutout Depth 23 1 2 Min Allow 11 16 for gt overlap of oven Cutout Width 28 1 2 Min over side edges per Opening 28 5 8 Max Between a as a Cutout Height 5113 16 Min Allow a minimum of At Least Junction Box 51 15 16 Max 21 for clearance to 28 1 2 Wide itoi adjacent corners Allow 1 Height mile Pin minimum for 51 13 16 Min NOTE If the cabinet does not SLIG Max have a front frame and the en sides are less than 3 4 thick of cutout shim both sides equally to establish the cutout width Recommended minimum cutout location Cabinet from floor 12 Width f the cabinet does not have a solid bottom two braces or runners must be installed level with the bottom of the cutout to 2 x4 or support the weight of the oven For double cielo ovens the runners and braces must level with support 275 Ibs bottom of cutout NOTE If marks blemishes or the cutout opening are visible above the Suitable installed oven it may be necessary to Bracing 2 toS t add wood shims under the runners and ee front trim until the marks or opening To 5 8 are covered pet alla Installation Instructions Cutout for Single Bui
8. le conduit must be securely attached to the clamp If the flexible conduit will not fit within the clamp do not install the oven until a clamp of the proper size is obtained NOTE TO ELECTRICIAN The 3 power leads supplied with this appliance are UL recognized for connection to heavier gauge household wiring The insulation of these 3 leads is rated at temperatures much higher than the temperature rating of household wiring The current carrying capacity of the conductor is governed by the wire gauge and the temperature rating of the insulation around the wire WARNING Improper connection of aluminum house wiring to copper leads can result in an electrical hazard or fire Use only connectors designed for joining copper to aluminum and follow the manufacturer s recommended procedure closely Place oven ona support to assist in connecting conduit I Turn off the circuit breaker or remove fuses to the oven branch circuit With the oven supported on a table or platform in front of the cabinet opening connect the flexible conduit to the electrical junction box as shown below Position the conduit in such a manner that it will lie on top of the oven in a natural loop when the oven is installed You will need to purchase an appropriate strain relief clamp to complete the connection of the conduit to the junction box Junction Box Location Conduit 48 1 2 Strain Relief Clamp not included must b
9. ler or service technician Be sure the oven is securely installed in a cabinet that is firmly attached to the house structure Weight on the oven door could cause the oven to tip and result in injury Never allow anyone to climb sit stand or hang on the oven door e Make sure the cabinets and wall coverings around the oven can withstand the temperatures up to 200 F generated by the oven gt WARNING The electrical power to the oven supply line must be shut off while line connections are being made Failure to do so could result in serious injury or death Electrical Requirements This appliance must be supplied with the proper voltage and frequency and connected to an individual properly grounded branch circuit protected by a circuit breaker or fuse having amperage as noted on rating plate Rating plate is located on oven frame Rating Plate Location behind oven door Electrical Requirements We recommend you have the electrical wiring and hookup of your oven connected by a qualified electrician After installation have the electrician show you where your main oven disconnect is located Check with your local utilities for electrical codes which apply in your area Failure to wire your oven according to governing codes could result in a hazardous condition If there are no local codes your oven must be wired and fused to meet the requirements of the National Electrical
10. lt In Oven Under Counter Gas or electric cooktops may be installed over this oven See cooktop installation instructions for cutout size See label on top of oven for approved cooktop models Gas and electrical connections for 30 gas cooktop must be located in an adjacent accessible location 240V E20BY to the right For 36 gas cooktop the connections may be made to the left Junction Box Location between existing cabinets Be sure Allow 1 overlap yikes they are attached top of oven and 22 Min securely since the Above Typical z y y 27 1 4 Min 11 16 overlap s t Countertop will anchor the oven 27 5 16 Max side edges of uppor Height in the cabinet cutout Platform Top and or side fillers may be necessary oman p na Pe 28 1 2 Min if unit is positioned 28 5 8 Max 36 Support Platform Required Reference dimension for maximum support height with typical 36 countertop height MUST SUPPORT 150 LBS NOTE This oven is not approved to be installed under a solid disk induction or downdraft modular cooktop Installation Instructions Electrical Connections ATTENTION INSTALLER All electric wall ovens must be hard wired direct wired into an approved junction box A plug and receptacle is NOT permitted on these products DO NOT shorten the flexible conduit The conduit strain relief clamp must be securely attached to the junction box and the flexib
11. rrying capacity of a conductor is governed by the wire gauge and also the temperature rating of the insulation around the wire NOTE ALUMINUM WIRING A WARNING IMPROPER CONNECTION OF ALUMINUM HOUSE WIRING TO THE COPPER LEADS CAN RESULT IN AN ELECTRICAL HAZARD OR FIRE Splice copper wires to aluminum wiring using special connectors designed and UL approved for joining copper to aluminum and follow the manufacturers recommended connector procedure closely NOTE Wire used location and enclosure of splices etc must conform to good wiring practice and local codes NOTES NOTES NOTES
12. the base pad ati a flat blade screwdriver DO NOT LIFT THE DOOR BY THE HANDLE Y Place hands on both sides of the door and close the oven door to the removal position This is half way between the broil stop and fully closed Broiler Pan and Grid Literature Pack Open oven door and remove literature Y Lift door up and pack broiler pan and grid and oven out until the racks hinge arms f clear the slots Remove Installation Instructions from literature pack and read them carefully before you begin Be sure to place all literature Owner s Manual Installations etc in a safe place for future reference Hinge Clears Slot NOTE The oven door is very heavy Be sure you have a firm grip before lifting the oven door off the hinges Use caution once the door is removed Do not lay the door on its handle This could cause dents or scratches Continued on following page Installation Instructions Y Pre Installation Checklist con Y Place the oven on a table or platform Y Remove the bottom trim from the top even with the cutout opening of the oven It will be installed at the Platform must support 150 Ibs single end of the installation process The 275 lbs double trim is wrapped separately and taped to the top of the unit Installation Instructions Cutout for Single Built In Oven Cutout Width 28 1 2 Min 28 5 8 Max gt overlap of oven over side ed
13. tout A WARNING Mounting screws must be used Failure to do so could result in the oven falling out of the cabinet causing serious injury b Secure the oven to cabinet with screws provided NOTE If the cabinet is particle board you must use 8 x 3 4 particle board screws These may be purchased at any hardware store Continued on following page Installation Instructions To install a single metal bottom trim assembly on some models use sections C3 and C4 To install a metal bottom trim with a plastic bottom trim on some models use sections C3 C5 Preparing for the Bottom Installing the Plastic Bottom Trim Installation a With oven installed take the bottom trim and center it on the bottom front edge of the cabinet opening With Lower Trim lt lt in Position Mark Using the trim as a template mark the center of each slot two total where the mounting holes will be drilled Remove Lower Trim Remove the trim Before Mounting Drill pilot holes into the center Holes of each template mark Installing the Metal Bottom Trim a Place the bottom metal trim centered over the pre drilled mounting holes Tape the edges of the trim down to maintain the alignment b Using two trim screws provided secure the bottom trim to the bottom edge of the cabinet If a plastic bottom trim is supplied proceed to C5 Side _ Trim Trim Scr
14. tted into Bottom of Hinge Slot Close the oven door D2 With the door at the same angle as the removal position half way between the closed and broil stop position seat the notch of the hinge arm into the bottom edge of the hinge slot The notch of the hinge arm must be fully seated into the bottom of the slot Hinge Arm Bottom Edge of Slot Hinge Notch 12 iW Pre Test Checklist lt 8 SSSS SS Installation Instructions Remove all protective film if present and any stickers Check to be sure that all wiring is secure and not pinched or in contact with moving parts Check that the bottom trim is installed properly see page 11 Check to be sure the mounting screws are installed and flush with the side trim see page 10 Operation Checklist Remove all items from the inside of the oven Check that conduit is securely connected to the junction box Turn on the power to the oven Refer to your Owner s Manual Verify that the bake and broil units and all cooking functions operate properly Check that the circuit breaker is not tripped nor the house fuse blown See your Owner s Manual for troubleshooting list NOTE TO ELECTRICIAN The power leads supplied with this appliance are UL recognized for connections to larger gauge household wiring The insulation of these leads is rated at temperatures much higher than the temperature rating of household wiring The current ca
Download Pdf Manuals
Related Search