GE RM24948 User's Manual
Contents
1. NOTE You can store any kind of code under any mode except TV I E you can store a VCR code under the CBL AUX button or a Cable code under the VCR DVD button etc However you can only store TV codes under the TV button 3 Button Functions Red Indicator Lights when any POWER Turns button is pressed product On or Off SETUP Used to setup the remote and for code search function TV CBL AUX VCR DVD Selects product to be operated CHANNEL Up Down Changes the channels Also controls DVD SKIP functions MUTE Turns off the TV sound while the picture remains VOLUME UP DOWN Changes the volume level of the product normally the TV RECORD PLAY STOP REW FF PAUSE VCR DVD control buttons operate your VCR or DVD even when the remote is set to operate the TV Note The REC button must be pressed TWICE to record from your VCR For some brands of VCRs you might need to press the REC button once then press it again for three seconds Code Entry using the Code List 1 Press and hold the SETUP button until SETUP the red indicator stays on then release the SETUP button 2 Press and release the desired device button TV VCR DVD etc The red indicator blinks then stays lit VOL I Oz 3 Enter the 4 digit code for your brand of TV VCR 4 etc from the Library Code Table by using the CH V v CHt and V buttons Use the CH button to enter the first dig2. RM24948 Universal Remote Instruction Manual POWER SETUP TV CBL AUX VCR DVD s 909 Table of Contents Introdueton iis x santestnereesadeduttenietasadscedies naea 3 SEUD ass cscs EN NJA 3 Battery Installation 3 Battery Saver uuvvunmugunnsseunm ka ska kale 3 Code AVEL cerien eaaa Eee 3 Oo CSL EEE 3 Button FUNCIONS sereset 4 Code Entry using the Code List 5 Code Seareh vnaamavartanessmaneaandveii 6 Using Your Remote 7 Code REEVAL sira iii ana noben 7 Controlling Devices with Power On and Off 8 Controlling Combo Devices 8 VCR DVD DVR Punch Through 8 Volume Mute Control and Punch Through 8 All Volume Mute Control to any one Mode 9 Returning Volume Mute Control to Initial Default 9 Troubleshooting 10 Congratulations on your purchase of the RM24948 Universal Remote Control The RM24948 is one of the most easy to use remote controls available today With the RM24948 juggling multiple remote controls is a thing of the past Your RM24948 controls up to three devices including the most popular brands of TV VCR DVD CBL and SAT The RM24948 is easy to use easy to program and it gives you total control at the touch of your fingertips Note Some functions from your original remote may not be controlled by this remo
3. ary from state to state If unit should prove defective within the warranty period return prepaid with dated proof of purchase to Jasco Products Company 311 N W 122nd Oklahoma City OK 73114 11 RM24948 Universal Remote Instruction Manual Jasco Products Company 311 N W 122nd Oklahoma City OK 73114 Made in China RM24948 07 06
4. e might operate some features but not all Try programing remote with a new code Remote may not be able to operate all features of your product or button names might be different than your product Red Indicator blinks after you program a product code e Remote did not accept the code Try to program the code again or try a different code Lost Your Codes Enclosed with this remote is a sticker on which you should write the codes for each device you programmed Apply the sticker to the back of the remote or somewhere convenient for future reference Also on the sticker is our website address which should you lose your codes or programming instructions you can find available on our website www jascoproducts com 10 90 Day Limited Warranty Jasco Products Company warrants this product to be free from manufacturing defects for a period of ninety days from the original date of consumer purchase This warranty is limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other products that may be used with this unit This warranty is in lieu of all other warranties express or implied Some states do not allow limitations on how long an implied warranty lasts or permit the exclusion or limitation of incidental or consequential damages so the above limitations may not apply to you This warranty gives you specific rights and you may also have other rights which v
5. erent Mode buttons to control both parts of the Combo device For example if you have a TV DVD Combo you might need to set up one code under the TV button to control the TV part AND separate code under any other Mode button to control the DVD part VCR DVD Punch Through This remote allows the 6 VCR transport buttons i e PLAY PAUSE STOP FF REWIND and REC to Punch Through control from any Mode programmed with TV SAT or Cable codes to the last VCR or DVD programmed Mode you used This feature will not operate if the programmed TV SAT or Cable code has its own VCR transport button control e g a TV Combo SAT PVR etc Volume Mute Control and Punch Through This remote lets you select which device Mode controls your Volume Mute buttons The remote is initially set for all device Modes to use their own Volume Mute control if present If the programmed code has no Volume Mute operation of its own then those buttons will punch through control to the TV Mode device without needing to change to TV Mode Any Mode chosen for Volume Mute control MUST have its own Volume Mute function or the Volume Mute buttons will do nothing 8 Using Your Remote cont Setting ALL Volume Mute Control to any one Mode This routine can set all Modes to punch through to any one chosen Mode for Volume Mute button control without the needing to change to that Mode 1 Press and hold SETUP until the red ETP indicator turns on then relea
6. it Use the V button to enter second digit Use the CH button to enter the third digit Use the V button to enter the fourth digit For Example To enter code 0107 don t press CH press V once don t press CHt and press V seven times The red LED blinks off with each keypress 4 Press the MUTE button to save the code MUTE Note for a valid code the red LED turns off For an invalid code the red LED blinks rapidly for three seconds before going off 5 With your device on press POWER If the device turns off no further programming is required Note If some buttons do not operate your equipment try one of the other codes for your brand POWER Setting up using Code Search If your TV does not respond after you have tried all the codes for your brand or if your brand is not listed try searching for your code by following these steps 1 Manually turn on the device TV VCR etc to be controlled 2 Press and hold the SETUP button until SETUP the red indicator stays on then release the SETUP button 3 Press and quickly release the desired E device button TV VCR DVD etc O The red indicator blinks off once 4 Press the POWER button repeatedly up to 300 times until the device to be controlled turns off The red indicator blinks off with each button press POWER MUTE 5 Press and release MUTE to install the code Write your codes down here for easy reference later Using Your Re
7. mote Code Retrieval Code Retrieval lets you identify the 4 digit library code stored under your device button For example if you want to find out what 4 digit code is stored under your TV device button follow the six steps below SETUP 1 Press and hold the SETUP button until the red indicator stays on then release the SETUP button 2 Press and release the desired device la button TV VCR DVD etc The red O indicator blinks then stays lit 3 Press and release the SETUP button SETUP The red indicator blinks once and remains lit 4 To find the first digit for the A A code stored under the device 4 4 button pressed in step 2 press CH and count the number of blinks 5 To find the second digit press V and count the number of blinks 6 To find the third digit press CH and count the number of blinks 7 To find the fourth digit press V and count the number of blinks This time the red indicator remains off once the fourth digit blinks are completed Remote operation returns to normal and Code Identification is now complete Using Your Remote cont Controlling Devices with Separate Power On and Off Buttons Some GE RCA and ProScan models require you to press the device button for more than one second to turn the device on and the POWER button to turn the device off Controlling Combo Devices Some Combo devices e g TV VCR TV DVD DVD VCR etc will require you to set up two diff
8. se SETUP 2 Press and hold MUTE until the red pk indicator blinks off then release MUTE 3 Press and release the desired Mode TV button TV VCR for Volume Mute control the red indicator blinks then stays on 4 Press and release MUTE and the red HUTE indicator turns off The red indicator will O blink rapidly for three seconds if the Mode you have selected has no Volume Mute control All other Modes will now punch through to your chosen Mode for Volume Mute control Returning Volume Mute Control to Initial Default Settings This routine returns Volume Mute control to its default factory settings i e all device Modes use their own Volume Mute control if present or else they will punch through control to the TV Mode device 1 Press and hold SETUP until the red JE indicator turns on then release SETUP 2 Press and hold MUTE until the red pily indicator blinks off then release MUTE 3 Press and release MUTE and the red MUTE indicator turns off Volume Mute control is returned to its default factory settings 9 Troubleshooting Remote does not operate your product e Press the device button of the product you want to control e Program the remote with a new code Install new batteries You might have to reprogram your remote after installing new batteries e Remote may not be compatible with your product Remote does not operate some features of your product e Sometimes a particular cod
9. te Use the original remote if available to control such functions Sometimes buttons other than described in these instructions may actually perform the function We recommend you experiment with the remote to identify if such situations pertain to your eguipment Battery Installation 1 On the back of the remote push down on the tab and lift the cover off 2 Match the batteries to the and marks inside the battery case then insert 2 AAA Alkaline batteries 3 Press the battery cover back into place Battery Saver Your remote automatically turns off if the buttons are depressed more than 30 seconds This will save your batteries should your remote get stuck ina place where the buttons remain depressed e g between the sofa cushions Code Saver You will have up to 10 minutes to change the batteries in your remote without losing codes you have programmed However do not press any buttons until batteries are installed in the remote If buttons are pressed without batteries in the remote all codes will be lost SETUP Code Setup The SETUP button is used to setup the remote You can either setup the remote using the code tables on separate sheet or you can search through the library of codes until you find a code that works for your product Please refer to Code Search on page 6 for more information on using the code search feature to learn how to search through the library of codes for your products
Download Pdf Manuals
Related Search