Home

GE DCF & DCD Installation Guide

image

Contents

1. BALLAST TRAY REMOVAL AND INSTALLATION Open lens door and remove Reflector plate assembly per instructions above To Remove Disconnect incoming power and lamp leads at the electrical disconnects Loosen 2 1 4 bolts pull tray out and drop to clear keyhole slots CAUTION Be prepared to support the weight of the ballast during removal Ballast Disconnect Capacitor Ballast Tray To Install Locate ballast between hooks on support Slide tray up under these hooks till 1 4 bolts can engage keyhole slots push in and up until tray is sitting on ledges of support Tighten 1 4 bolts and install two electrical disconnects Hooks Disconnects Support WIRING IF SINGLE VOLTAGE All single voltage ballasts are pre wired such that user need only connect the supply conductors IF MULTIVOLT 120 208 240 277 Connect the ballast lead with the insulated terminal to the desired voltage terminal as indicated on the ballast terminal nameplate IF MULTIWATT Multiwatt ballasts are available in various combinations of wattage See wiring instructions on wiring tag inside the luminaire Removal of ballast tray may be required for access to ballast terminals Follow instructions for ballast tray removal and installation as outlined above Move insulated terminal to appropriate ballast terminal specified on wiring tag inside luminaire CLEANING INSTRUCTIONS AND CAUTIONS Internal Sho
2. GEH 5750D GE INSTRUCTIONS Lighting Solutions Flat Top Decasphere Luminaire READ THOROUGHLY BEFORE INSTALLING A WARNING Risk of electric shock e Turn power off before servicing see instructions Make all electrical connections in accordance with the National Electrical Code and any applicable INSTALLATION local code requirements Step 1 Verify that supply voltage is correct by comparing A Drill pole per Fig A if a square pole or Fig B if a it to nameplate round pole Fig A Replace power fuses only with fuses of the same type and ratings GENERAL This luminaire is designed for use in outdoor applica tions and must adhere to 25 C Max ambient temperature limitation Install and maintain it according to the following recommendations A CAUTION Unit will fall if not installed properly e Follow installation instructions Cover Luminaire pound Jie Jt Sa Bol er eels Power Leads 3 8 bolts amp Lockwashers 8 32 Screw These instructions do not purport to cover all details or variations in equipment nor to provide for every possible contingency to be met in connection with installation operation or maintenance Should further information be desired or should particular problems arise which are not covered sufficiently for the purchaser s purposes the matter should be referred to GE Lightin
3. g Solutions B Mount frame and nut plate assembly to pole with 2 3 8 bolts and lockwashers If a round pole install Round Pole Adaptor C Attach luminaire to frame feeding power leads through Frame tube Secure with 2 3 8 bolts and lockwashers D Install cover over Frame and secure with 8 32 Screw E Splice power leads to incoming power Install pole cap Strain relief for incoming power must be provided in the pole top by the customer RELAMPING CLEANING AND LIGHT DISTRIBUTION CHANGES AY CAUTION Risk of burn e Allow lamp fixture to cool before handling NOTE Use only lamps specified on nameplate Observe lamp manufacturer s recommendations and restrictions on lamp operation particularly ballast type burning position etc To Open Lens Door Loosen 3 1 4 turn fasteners by turning CCW Phillips screw driver required Lens door is hinged on pole side To Remove the Lens Door Open to the position shown lift and slide forward To Remove or Rotate the Reflector Reflector may be removed to gain access to ballast and wiring or rotated 90 CW or CCW to orient light distribu tion by loosening screws at each of 4 keyhole slots in reflector plate assembly Assembly is tethered to luminaire If it is necessary to detach assembly remove screw that holds tether to reflector plate Reflector Plate Screws 4 Reflector Plate Asm 1 4 Turn Fasteners 3 Places Lens Door
4. uld internal reflector system require cleaning use only non abrasive neutral pH 6 8 cleaner containing no chlorinated or aromatic hydrocarbons Rinse clean and wipe External Clean glass lens with a mild soap and water solution rinse clean and wipe dry GE Lighting Solutions e 1 888 MY GE LED e www gelightingsolutions com 1 888 69 43 533 GE Lighting Solutions is a subsidiary of the General Electric Company Evolve and other trademarks belong to GE Lighting Solutions The GE brand and logo are trademarks of the General Electric Company 2011 GE Lighting Solutions Information provided is subject to change without notice All values are design or typical values when measured under laboratory conditions 35 201578 T4 11 99

Download Pdf Manuals

image

Related Search

Related Contents

TouchSystems SH5580I-U3  Velleman DVM9912 multimeter  Keystone KSTFA060UAG Use and Care Manual  Manual de instrucciones Itaca 100 Calefactora  rt-08 solar  

Copyright © All rights reserved.
Failed to retrieve file