GE DCF & DCD Installation Guide
Contents
1. GE Lighting Solutions GEH 5749D INSTRUCTIONS Dome Top Decasphere Luminaire READ THOROUGHLY BEFORE INSTALLING A WARNING Risk of electric shock e Turn power off before servicing see instructions Make all electrical connections in accordance with the National Electrical Code and any applicable local code requirements Verify that supply voltage is correct by comparing it to nameplate Replace power fuses only with fuses of the same type and ratings GENERAL This luminaire is designed for use in outdoor applica tions and must adhere to 25 C Max ambient temperature limitation Install and maintain it according to the following recommendations A CAUTION Unit will fall if not installed properly e Follow installation instructions Cover Luminaire 1 4 20 Screw Nut Plate N j 3 8 bolts amp Lockwashers 8 32 Screw g Power Leads K lt O INSTALLATION Step 1 A Drill pole per Fig A if a square pole or Fig B if a round pole Fig A T be es pole pia 2 Holes Fig pound pole ter s adap i ge N p jt S 2 gets These instructions do not purport to cover all details or variations in equipment nor to provide for every possible contingency to be met in connection with installation operation or maintenance Should further information be desired or should par2. quired for access to ballast terminals Follow instructions for ballast tray removal and installation as outlined above Move insu lated terminal to appropriate ballast terminal specified on wiring tag inside luminaire CLEANING INSTRUCTIONS AND CAUTIONS Internal Should internal reflector system require cleaning use only non abrasive neutral pH 6 8 cleaner containing no chlorinated or aromatic hydrocarbons Rinse clean and wipe External Clean glass lens with a mild soap and water solution rinse clean and wipe dry GE Lighting Solutions e 1 888 MY GE LED e www gelightingsolutions com 1 888 69 43 533 GE Lighting Solutions is a subsidiary of the General Electric Company Evolve and other trademarks belong to GE Lighting Solutions The GE brand and logo are trademarks of the General Electric Company 2011 GE Lighting Solutions Information provided is subject to change without notice All values are design or typical values when measured under laboratory conditions 35 201578 T3 11 99
3. ticular problems arise which are not covered sufficiently for the purchaser s purposes the matter should be referred to GE Lighting Solutions B Install Nut Plate and secure with 1 4 screw fur nished C Attach Frame to luminaire feeding power leads through Frame tube Secure with 2 3 8 bolts and lockwashers D Mount Frame Luminaire Assembly to pole with 2 3 8 bolts and lockwashers If a round pole install Round Pole Adaptor E Install cover over Frame and secure with 8 32 Screw F Splice power leads to incoming power Install pole cap Strain relief for incoming power must be provided in the pole top by the customer RELAMPING CLEANING AND LIGHT DISTRIBUTION CHANGES A CAUTION Risk of burn e Allow lamp fixture to cool before handling Use only lamps specified on nameplate Observe lamp manufacturer s recommendations and restric tions on lamp operation particularly ballast type burning position etc ToOpenLens Door Loosen 3 1 4 turn fasteners by turning CCW Phillips screw driver required Lens door is hinged on pole side ToRemovetheLens Door Open to the position shown lift and slide forward ToRemoveorRotatethe Reflector Reflector may be removed to gain access to ballast and wiring or rotated 90 CW or CCW to orient light distribution by loosening screws at each of 4 keyhole Slots in reflector plate assembly Assembly is tethered to luminaire If it is necessar
4. y to detach the assembly remove screw that holds tether to reflector plate Reflector Plate Screws 4 L Reflector Ih Plate Asm Sus Turn Fasteners JL 3 Places Lens Door BALLAST TRAY REMOVAL AND INSTALLATION Open lens door and remove Reflector plate assembly per instructions above ToRemove Disconnect incoming power and lamp leads at the electrical connectors Loosen 2 1 4 bolts pull tray out and drop to clear keyhole slots Disconnect Ballast Capacitor Ballast Iray Guides 1 bolts c A CAUTION Be prepared to support the weight of the ballast during removal Tolnstall Locate guide to each side of support Slide tray up under ears till 1 4 bolts can engage keyhole slots push in and up until tray is sitting on ledges of support Tighten 1 4 bolts Disconnects Ears Guides Support 1 4 bolts Ledge of Support se WIRING IF SINGLE VOLTAGE All single voltage ballasts are pre wired such that user need only connect the supply conductors IF MULTIVOLT 120 208 240 277 Connect the ballast lead with the insulated terminal to the desired voltage terminal as indicated on the ballast terminal nameplate IF MULTIWATT Multiwatt ballasts are available in various combinations of wattage See wiring instructions on wiring tag inside the luminaire Ballast Tray Removal of ballast tray may be re
Download Pdf Manuals
Related Search