GE CV936 User's Manual
Contents
1. Remove screws Using two large flat washers supplied install wood screws or wall fastener screws loosely into lower mounting holes Do not tighten Check hood level Tighten upper screws Tighten lower mounting screws For additional security drive screws through the original wood support screw holes in the back of the hood 1 Ft 0 3 m 1 2 5 cm Installation Instructions Alternate Mounting Method INSTALL HOOD TO SOFFIT OR BENEATH CABINETS SKIP THIS STEP IF USING WALL MOUNTING METHOD IMPORTANT Framing must be capable of supporting 100 Ibs 45 3 kg When necessary the hood may be installed so that it is supported by the soffit The soffit should be constructed with 2 x 4 s Determine the installation location Continue the centerline forward on the bottom of the cabinet or soffit p Opening For Ductwork 10 W x 8 7 16 D 10 W x 8 7 16 D Centerline to Center of Stud 145 175 30 Models 36 Models Mounting screws must be secured to 2 x 4 studs Dim A at locations shown in the above chart e Allow minimum opening Dim B to accommodate the duct transition in the soffit Rear Wall 1 1 T 53 8 3 mu 8 7 16 i l senatores E irre ied ton s I Top View Front Side Cut a 104 x 8 7 16 hole through bottom of soffit or cabinet for duct transition as shown 152. To order To order CERAMA BRYTE Stainless Steel Cleaning Polish and Conditioner please call our toll free number National Parts Center 1 800 661 1616 www GEAppliances ca CERAMA BRYTE Stainless Steel Cleaning Polish and Conditioner PM10X313 Reusable Metal Grease Filters The hood has 2 metal reusable grease filters The metal filters trap grease released by foods on the cooktop They also help prevent flaming foods on the cooktop from damaging the inside of the hood For this reason the filters must ALWAYS be in place when the hood is used The grease filters should be cleaned once a month or as needed To clean the grease filters soak them and then swish them around in hot water and detergent Don t use ammonia or ammonia products because they will darken the metal Do not use abrasives or oven cleaners Light brushing can be used to remove embedded dirt Rinse shake and let them dry before replacing They may also be cleaned in an automatic dishwasher Painted Surfaces on some models To clean the hood surface use a hot damp cloth with a mild detergent suitable for painted surfaces Use a clean hot damp cloth to remove soap Dry with a dry clean cloth www GEAppliances ca To remove Grasp the filter handle and pull it up forward and out To replace 7 Hold the filter at the bottom with the handle 2 Place the top end of the filter X against the inside
3. www geappliances ca MAIL TO P O BOX 1780 MISSISSAUGA H Q 1 JA ENREGISTREMENT SUR INTERNET A www electromenagersge ca POSTEZ ONTARIO L4Y 4G1 i E H i f ORIMO MRS MME FIRST NAME PR NOM LAST NAME NOM O ff D MSSMLLE n ws For Canadian Zii i amp _ 1 STREETNO NORUE STREET NAME RUE APT NOJAPP RR M Customers gt 5 Lu 22 zi M CITY VILLE PROVINCE POSTAL CODE CODE POSTAL f 22 lt lt Z 1 AREA CODE IND REG TELEPHONE TELEPHONE E MAIL COURRIEL LLI I zu S 5 DID YOU PURCHASE A SERVICE CONTRACT FOR THIS APPLIANCE YES OUI IF YESISI OUI EXPIRATION i 1 z T AVEZ VOUS ACHET UN CONTRAT DE SERVICE POUR CET APPAREIL NONON O l Pour les m LA NAME OF SELLING DEALER NOM DU MARCHAND MODEL MOD LE l consommateurs EB i canadiens zi COE N ATONDATE DATEDINSTALATON CORRESPONDENCE ENGLISH Lo CORRESPONDANCE L1 FRAN AIS SERIAL S RIE i o I l I l 1 l 1 l 1 l Bi 22 Range Hood Warranty All warranty service provided by our Factory Service Centers or Staple your receipt here a an authorized Customer Care technician To schedule service Proof of the original purchase on line 24 hours a day visit us at www GEAppliances ca or call date is needed to obtain service 1 800 561 3344 under the warranty For The Period Of Mabe Will Replace One Year Any part of the range hood which fails due to a defect in materials or workmanship From
4. IMPORTANT For additional support and to minimize vibration during operation we strongly recommend that the hood also be secured to the back wall with wall fasteners 30 Models 2 9 16 Top View Front Side 36 Models 2 1 4 Top View Front Side Drill four 1 8 pilot holes in locations shown If mounting to the underside of a cabinet with a recessed bottom install shims to fill the gap Cabinet or ka Soffit Transition V Gap N Add Shims If Bottom Is Recessed Engage Keyhole Slots and Push Back Wall Back to Wall Drive mounting screws into the studs until they protrude 1 4 This 4 gap will provide clearance to engage the keyhole slots in the top of the hood Lift hood onto mounting screws Slide back against the rear wall Pull house wiring through the knockout at the rear or the top of the hood Tighten mounting screws 1 Ft 0 3 m 1 2 5 cm Installation Instructions 5 INSTALL CEILING BRACKET 6 CONNECT DUCTWORK The ceiling bracket must be installed when the duct Push duct over the end of the transition until it cover is used to span 24 or more height above the reaches the stop tabs hood The bracket will hold the decorative duct cover in Install ductwork making connections in direction of 8 place at the top airflow as illustrated Note The ceiling brac
5. hole approximately 1 dia 10 1 16 down from the top of the hood 11 1 8 to the right of the centerline for 30 models or 14 1 8 to the right of the centerline for 36 models Remove top or rear knockout depending on your installation 1 Ft 0 3 m 1 2 5 cm 13 FOR CEILING P4 VENT DUCTING R Electrical 6 7 8 Centerline To Wall z 7 Dia Hole n i Centerline ut 8 Min above FOR WALL VENT DUCT f Top of Hood Top of Hood M g t Wood Support 15 3 8 Bottom of Hood i Electrical FOR DUCTING THROUGH REAR WALL Measure the supplied duct transition with any straight run length of duct used plus 90 elbow height Draw a horizontal line on the wall intersecting the centerline 14 1 8 for 36 Models 11 1 8 for 30 Models Knockout Locations or 36 Models or 30 Models Installation Instructions 1 INSTALL HOOD SUPPORT IMPORTANT Framing must be capable of supporting 100 Ibs 45 3 kg Locate at least 2 vertical studs at the wood mounting location by tapping drywall with a hammer or use a stud finder Center the supplied wood horizontal support left to right and below the marked line Wood Support E Ul x Centerline of Installation space Drill 1 8 pilot holes through the support drywall and into the studs Secure the support to 2 or morevertical studs with supplied wood screws I
6. is supplied for vertical exhaust Use locally supplied elbows to vent horizontally through the rear wall See page 13 Determine the exact location of the vent hood Use the shortest and straightest duct route possible For satisfactory performance duct run should not exceed 100 equivalent length for any duct configurations Refer to Duct Fittings chart to compute the maximum permissible length for duct runs to the outdoors Use metal ductwork only A transition piece for 7 round duct is supplied Use 7 round duct or you may use 34 x 12 rectangular Install a wall cap or roof cap with damper at the exterior opening Order the wall or roof cap and any transition needed in advance Kit JXDW1 Order kit JXDWI if your installation requires horizontal ducting from the top of the hood through the back wall and You have an 8 ft ceiling and need to use a JXCH Series Chimney Cover or You have a 12 cabinet or 12 soffit that the hood is to be mounted beneath This kit provides a duct transition from 7 round to 3 x 10 rectangular for through the wall venting Wall Framing for Adequate Support This vent hood is heavy Adequate structural support must be provided The hood must be secured to vertical studs in the wall See page 14 We strongly recommend that the vent hood with duct cover be on site before final framing and wall finishing This will also help to accurately locate the ductwork and
7. CALL E disconnecting means to prevent power from THE FIRE DEPARTMENT 2 being switched on accidentally When the B NEVER PICK UP A FLAMING PAN service disconnecting means cannot be locked You may be burned E securely fasten a prominent warning device C DO NOT USE WATER including wet C such as a tag to the service panel dishcloths or towels a violent steam 2 C Do not use this unit with any solid state speed explosion will result e control device D Use an extinguisher ONLY if D This unit must be grounded 1 You know you have a Class ABC t CA U TI ON For general ventilating use only E ana gout reads SeenON E Do not use to exhaust hazardous or explosive p D S materials and vapors 2 The fire is small and contained in the d area where it started G CA U TI ON To reduce risk of fire and to 3 The fire department is being called S properly exhaust air be Sure to duct air outside 4 You can fight the fire with your back to a Do not vent exhaust air into spaces within walls or amexit g ceilings or into attics crawl spaces or garages Based on Kitchen Fire Safety Tips published e by NFPA A D eo P amp Consumer Support www GEAppliances ca gt WARNING ro repuce THE RISK oF WARNING ro REDUCE THE RISK OF FIRE suoyonysuy Ajajes FNNS A RANGE TOP GREASE FIRE USE ONLY METAL DUCTWORK A Never leave surface units unattended at high Do not attempt to repair or repl
8. MPORTANT Screws must penetrate at least 114 into vertical studs Countersink screws into support nstall mounting screws in the center of the wood support 13 1 16 from the centerline The screws should protrude forward 4 This 4 gap will provide clearance to hang the hood 14 2 INSTALL TRANSITION IMPORTANT Remove shipping tape from damper and check that damper moves freely Remove Shipping Tape on Transition Place the transition piece over the hood exhaust Secure transition to hood with 4 screws provided Use duct tape to seal the connection 3 INSTALL HOOD ONTO WALL Lift the hood and place over the wood support The top keyhole slots in the hood should engage the protruding mounting screws Allow the hood to slide down into position Pull house wiring through knockout at the rear or the top of the hood Check to be sure the hood is level and centered The arrow shaped cutout in the back of the hood allows viewing the marked centerline Remove cover from junction box le Cutout Centerline of Installation space posse Drill Bottom Mounting Hole Locations Drill 1 8 pilot holes into the two lower mounting holes Enlarge the holes if they did not enter studs to 3 8 Tap anchors for wall fasteners into bottom holes Install screws by hand into the fasteners to allow anchors to expand against the wall
9. SHRAE This Hood Must Use 7 Round Duct It Can Transition To 3 x 12 Duct Kit JXDW1 Order kit JXDWI if your installation requires horizontal ducting from the top of the hood through the backwall and You have an 8 ft ceiling and need to use a JXCH Series Chimney Cover or You have a 12 cabinet or 12 soffit that the hood is to be mounted beneath This kit provides a duct transition from 7 round to 34 x 10 rectangular for through the wall venting Using a smaller diameter duct size will reduce performance Equivalent Length 1 ft per foot length 1 ft per foot length Quantity Used Duct Piece Dimensions Round straight 344 x 12 straight 90 elbow 8 ft 45 elbow 6 ft 3 x 12 or 90 elbow 34 x 12 or 45 elbow 34 x 12 or 90 flat elbow 7 round to 934 x 12 transition 34 x 12 to 7 round transition 7 round to 34 x 12 transition 90 elbow 34 x 12 to7 round transition 90 elbow Round wall cap with damper 344 x 12 wall cap with damper 7 round roof cap Round roof vent 24 ft CAUSES o IRSE TI Actual length of straight duct plus duct fitting equivalent Equivalent length of duct pieces are based on actual tests conducted by GE Evaluation Engineering and reflect requirements for good venting performance with any ventilation hood 10 Total Duct Run Total Equivalent Length Install
10. Vented Range Hoods www GEAppliances ca Safety Instructions 2 3 Operating Instructions Light Controls 5 3620540 eas 4 Vent Controls i4 ese oso hr bs 4 Care and Cleaning Grease Filters 5 Hood Lights x eeses t ber 6 Hood Surfaces 5 Stainless Steel Surfaces 5 Installation Instructions 7 18 Troubleshooting Tips 20 Consumer Support Consumer Support Back Cover Product Registration 21 22 Warranty aa veda e et ord dd 23 Write the model and serial numbers here Model Serial You can find them on a label on the inside of the hood Owners Manual and Installation Instructions V936 CV936 350A4502P550 08 07 ATS IMPORTANT SAFETY INFORMATION M READ ALL INSTRUCTIONS BEFORE USING 3 RY EMI SAFETY PRECAUTIONS 7 Y WARNING ro reouce THe risk oF Fire WARNING ro eouce tHe risk or E ENS ELECTRIC SHOCK OR INJURY TO PERSONS OBSERVE INJURY TO PERSONS IN THE EVENT OF A RANGE o THE FOLLOWING TOP GREASE FIRE OBSERVE THE FOLLOWING A Use this unit only in the manner intended A SMOTHER FLAMES with a close fitting by the manufacturer If you have questions lid cookie sheet or metal tray then turn off e contact the manufacturer the burner BE CAREFUL TO PREVENT S B Before servicing or cleaning unit switch power BURNS If the flames do not go out S off at service panel and lock the service immediately EVACUATE AND
11. ace any settings Boilovers cause smoking and greasy part of your hood unless it is specifically spillovers that may ignite Heat oils slowly on recommended in this guide All other servicing low or medium settings should be referred to a qualified technician B Always turn hood ON when cooking at high heat or when cooking flaming foods C Clean ventilating fans frequently Grease should not be allowed to accumulate on fan or filter D Use proper pan size Always use cookware appropriate for the size of the surface element WARNING ro REDUCE THE RISK OF FIRE ELECTRIC SHOCK OR INJURY TO PERSONS OBSERVE THE FOLLOWING A Installation work and electrical wiring must be done by qualified person s in accordance with all applicable codes and standards including fire rated construction e S E m Bw c a S Q S B Sufficient air is needed for proper combustion and exhausting of gases through the flue chimney of fuel burning equipment to prevent back drafting Follow the heating equipment manufacturer s guideline and safety standards such as those published by the National Fire Protection Association NFPA and the American Society for Buiuea pue 91279 Heating Refrigeration and Air Conditioning a Engineers ASHRAE and the local code S authorities C When cutting or drilling into wall or ceiling e do not damage electrical wiring and other S hidden utilities D Ducted fans must al
12. allation a decorative duct cover is available to conceal the ductwork running from the top of the hood Use of the duct cover requires special consideration to the installation height above the countertop See page 12 for details 1 Ft 0 3 m 1 2 5 cm OPTIONAL ACCESSORIES Duct Cover A Decorative duct cover is available to accommodate 8 to 10 ft ceiling heights The duct cover will expand from 12 Min or 24 to 34 Max height The duct cover conceals the ductwork running from the top of the hood to the ceiling The duct cover accessory fits both 30 and 36 wide models Order the duct cover accessory at the same time as the vent hood All accessories should be on site at the time of hood installation Order the correct color to match your model JXCHBB Black JKCHWW White JXCHCC Bisque JXCHSS Stainless Steel Ceiling Bracket 2Wood 2 Washers 2 Wall Screws Fasteners 2 Piece Duct Cover With Ceiling Bracket 4 Phillips Head Screws 2 Phillips Head Decorative Screws Commercial Filter Kit Use this kit to replace supplied filters JXBF30SS Commercial Filter Kit for 30 wide models JXBF36SS Commercial Filter Kit for 36 wide models Includes 2 commercial filters and 2 drip trays 2 Baffle Filters 2 Drip Trays Installation ADVANCE PLANNING Ductwork Planning This hood may be vented vertically through upper cabinets soffit or ceiling A duct transition piece
13. ation Instructions TOOLS AND MATERIALS REQUIRED NOT SUPPLIED Phillips and Flat blade screwdrivers Pencil and Duct tape tape measure pivoting hex socket D A Safety glasses ex 050 cUL Listed Wire nuts Electric drill with 1 8 and 3 8 bits OAOA Spirit level CT Flashlight Saber saw or Key Hole Saw d Ladder Allen Wrench Additional Materials e 120V 60Hz 15 or 20 Amp 2 wire with ground Properly grounded branch circuit Strain relief for junction box 7 round metal duct or 34 x 12 rectangular duct length to suit installation 11 REMOVE THE PACKAGING Remove parts package from the V shaped cardboard insert Remove insert Remove shipping pads Lift the hood out of the box CAUTION Lift hood by grasping the outside edges of the exhaust opening on the top Do not lift hood by the exhaust opening divider damage will occur Package Wood Mounting Support Mounted on ___ Skid E Shipping Carton Remove transition duct piece from the inside of the hood Discard screws The vent hood motor is shipped secured to the skid with 4 screws Locate and remove 2 screws on each side of the motor Discard the shipping skid Hold Down Screws Hold Down Screws From the inside of the hood remove shipping screws holding the wood mounting piece to the back side of the hood Set aside woo
14. d mounting piece and screws for later installation Do not discard Remove junction box cover and knockout nstall strain relief onto back or top of hood Remove all tape and packing material from the hood duct transition and motor 1Ft 0 3m 1 2 5 cm Installation Instructions PARTS PROVIDED Locate the hardware accessory box packed with the hood and check contents fast Screws wall eners washers Filter Support 2 Aluminum Duct Transition Grease Filters with Damper 2 Control Knobs DUCT COVER REQUIREMENTS We recommend that the vent hood and decorative duct cover if used be on site before final framing and wall finishing This will help to accurately locate studs ductwork and electrical service Read these instructions to determine if the duct cover accessory can be used for your installation situation Duct Cover Accessory Use the decorative duct cover to conceal duct work running from the top of the hood to the ceiling The duct cover accessory consists of 2 pieces The outside piece is 12 high the inside piece is 22 Nested together they are 24 min expanding to a total maximum height of 34 The outside piece can be used alone to fill a 12 height For heights over 12 the ceiling bracket must be installed to secure the cover at the top To avoid unsightly gaps plan the hood installation height for duct cover use The cover will fit a 12
15. electrical service DUCT FITTINGS Follow these guidelines for proper duct sizing in the ducting charts DUCTING CHART 30 and 36 Models Equivalent Length in Feet for 7 Round Duct 25 50 75 100 125 150 600 500 400 300 200 Air Volume in CFM 7 Round 90 Elbow 8 ft 7 Roof Cap 30 ft MAXIMUM DUCT LENGTH 7 dia duct should not exceed 100 equivalent feet Instructions DECORATIVE DUCT COVERS A decorative duct cover is available to fit both model widths The duct cover conceals the ductwork running from the top of the hood to the ceiling or soffit The duct cover will fit 8 ft to 10 ft ceiling heights See page 12 for details POWER SUPPLY IMPORTANT Please read carefully WARNING FOR PERSONAL SAFETY THIS APPLIANCE MUST BE PROPERLY GROUNDED Remove house fuse or open circuit breaker before beginning installation Do not use an extension cord or adapter plug with this appliance Follow National electrical codes or prevailing local codes and ordinances Electrical supply This vent hood must be supplied with 120V 60Hz and connected to an individual properly grounded branch circuit and protected by a 15 or 20 amp circuit breaker or time delay fuse Wiring must be 2 wire with ground If the electrical supply does not meet the above requirements call a licensed electrician before proceeding Route house wiring as close to the installation location as
16. front of the hood Slide it up until it stops and push the bottom end back until it snaps into place IS Do not use steel wool pads or other abrasive cleaners They will scratch the surface Stainless Steel Surfaces on some models Do not use a steel wool pad it will scratch the surface 7 Shake bottle well 2 Place a small amount of CERAMA BRYTE Stainless Steel Cleaning Polish and Conditioner on a dry cloth or dry paper towel Clean a small area approximately 8 x 8 or 20 3 x 20 3 cm rubbing with the grain of the stainless steel if applicable 4 Dry and buff with a clean dry paper towel or soft cloth 5 Repeat as necessary suoyonysuy Ajajeg suoijanijsu Guyesadg X to Q Q I Buiuea sdij Burjooisa qnoa uoddns sauimnsuoy Operating Instructions Safety Instructions Care and Cleaning A D eo P amp Consumer Support Care and cleaning of the vent hood Be sure electrical power is off and all surfaces are cool before cleaning or servicing any part of the vent hood Receptacle Glass cover Socket Hood Lights NOTE The glass cover should be removed only when cold Wearing latex gloves may offer a better grip CA U TI ON Before replacing your light bulb disconnect the electrical power to the hood at the main fuse or circuit breaker panel Be sure to let the light cover and bu
17. haust opening BR Motor Attachment Bracket Rotate motor upwards until it aligns with the attachment screw location Secure the motor to attachment bracket at the front of the opening with washer and screw provided Plug the motor connector into the mating hood connector See the illustration for the hood connector location Touch the hood to locate and make the connection IMPORTANT Hold the connector so the two square corner terminals 20 are at the top as you position the connector to plug it in 8 CONNECT ELECTRICAL Verify that power is turned off at the source WARNING If house wiring is not 2 wire with a ground wire a ground must be provided by the installer When house wiring is aluminum be sure to use cUL approved anti oxidant compound and aluminum to copper connectors A Remove C Insert Power Junction Box Coduit Thru Cover Strain Relief and Tighten White Ground ae Black B Check That White Black and Green Hood Wires Are Threaded Thru Small Hole in Bracket D Use cUL Listed Wire Nuts Use wire nuts to connect incoming ground to green white to white and black to black Push wires into junction box and replace cover Be sure wires are not pinched 9 INSTALL DUCT COVERS To install the 12 duct cover alone Place the 12 section of the decorative duct cover on top of the hood Secure the co
18. ion of this vent hood requires k 21 basic mechanical and electrical skills Completion time 1 to 3 hours 30 Models Requires a 30 Wide Opening Proper installation is the responsibility of the installer Product failure due to improper installation is not covered under the Warranty Lux Due to the weight and size of these vent hoods and to reduce the risk of personal injury or damage to the product TWO PEOPLE ARE REQUIRED FOR PROPER INSTALLATION CAUTION D LL k 21 F O R Y O U R SAFETY ee Wide Opening WARNING Before beginning the installation switch power off at service panel and lock 1Ft 0 3m 1 2 5 cm the service disconnecting means to prevent power from being switched on accidentally When the service disconnecting means cannot be locked securely fasten a prominent warning device such as a tag to the service panel Installation Instructions INSTALLATION CLEARANCES These vent hoods are designed to be installed onto a wall They may be installed beneath a soffit or cabinet Install these hoods 24 Min to 36 Max above the cooking surface SOFFIT INSTALLATION SOFFIT it m In this installation the ductwork running from the top of the hood will be concealed in the soffit or upper cabinetry WALL MOUNT INSTALLAT For this inst
19. ket is not required when using Secure joints in ductwork with sheetmetal screws only the 12 section of the duct cover Wrap all duct joints with duct tape for an airtight seal Use duct tape to seal the flange connection nstall the 2 small screws into the sides of the duct bracket Remove the screws Pre tapping the holes will insure ease of final installation Match center notch on the bracket to the centerline on the wall and flush against the ceiling Mark the 2 screw hole locations Drill 1 8 pilot holes in marked bracket location Duct Tape If pilot holes do not enter studs enlarge the holes to Over Seam 3 8 and install wall fastener anchors and Screw Secure the bracket to the rear wall with wood screws and washers Use wall anchors if needed Note Bracket has 2 sets of holes Use larger holes for wall Duct Tape fasteners or wood screws with washers Use smaller holes for wood screws with washers Duct Tape Pad Over Flange Bracket When Duct Cover is Used to Span 24 or more Install Ceiling r a CAUTION Do not use sheet metal screws at the hood flange connection Doing so will prevent proper damper operations Seal connection with tape only See Step 9 to Install Duct Cover 1 Ft 0 3 m 1 2 5 cm 16 Installation Instructions 7 INSTALL MOTOR Align and engage the slots in the blower assembly to the 3 hooks at the rear of the ex
20. lb cool completely For your safety do not touch a hot bulb with bare hands or a damp cloth To remove 7 Turn the glass cover counterclockwise until the glass cover clears the socket 2 Using gloves or a dry cloth remove the bulb by pulling it straight out To replace 7 Use a new 12 volt 20 watt maximum Halogen bulb for a G 4 base 2 Using gloves or a dry cloth remove the new bulb from its packaging NOTE Do not touch the new halogen bulb with bare fingers Touching the bulb with bare fingers will significantly reduce the life of the bulb Receptacle Use gloves or cloth Push the bulb straight into the receptacle all the way Place the glass cover onto the socket and turn clockwise until secure For improved lighting clean the glass cover frequently using a damp cloth This should be done when the hood is completely cool Reconnect electrical power to the hood Installation Range Hood Instructions Questions Call 1 800 561 3344 or Visit our Website at www GEAppliances ca BEFORE YOU BEGIN PRODUCT DIMENSIONS Read these instructions completely and carefully IMPORTANT Save these instructions for local inspector s use IMPORTAN T Observe all governing codes and ordinances Note to Installer Be sure to leave these instructions with the Consumer Note to Consumer Keep these instructions for future reference Skill level Installat
21. min height from the top of the hood to the ceiling or 24 min and expanding up to 34 from the top of the hood to the ceiling THE DUCT COVER CANNOT BE USED WHEN THE DISTANCE ABOVE THE TOP OF THE HOOD IS BETWEEN 12 AND 24 1 Ft 0 3 m 1 2 5 cm Review the following examples to ensure a trouble free installation using the duct cover accessory 8 ft Ceiling 8 ft ceilings The hood t must be installed at 30 S above the cooking surface or 66 above the floor The duct cover willnot fit if the hood is installed at a lower or higher height Use the outside 12 section discard the inside section Ey 1 IT 9 ft ceilings Install the hood 24 min and up to a maximum of 30 above the cooking surface The duct cover will expand to reach ceiling height 10 ft Ceiling 1 10 ft ceilings nstall the hood 32 min to 36 max above the cooking surface The duct cover will expand to a maximum of 34 above the top of the hood to meet the ceiling Installation Instructions DETERMINE HOOD DUCTWORK AND WIRING LOCATIONS Measure desired distance from the bottom of the hood to the cooking surface 24 min to 36 max Refer to the previous page if the accessory duct cover will be used Use a level to draw a ho
22. possible in the ceiling soffit or wall See page 13 for details Connect the wiring to the house wiring in accordance with local codes Grounding instructions The grounding conductor must be connected to a ground metal permanent wiring system or an equipment grounding terminal or lead on the hood WARNING The improper connection of the equipment grounding conductor can result in a risk of electric shock Check with a qualified electrician or service representative if you are in doubt whether the appliance is properly grounded 1 Ft 0 3 m 1 2 5 cm Installation Instructions DUCT FITTINGS Use this chart to compute maximum permissable lengths for duct runs to outdoors Note Do not exceed maximum permissable equivalent lengths Maximum duct length 100 foot for vent hoods Flexible ducting If flexible metal ducting is used all the equivalent feet values in the table should be doubled The flexible metal duct should be straight and smooth and extended as much as possible Do NOT use flexible ducting Note Any home ventilation system such as a ventilation hood may interrupt the proper flow of combustion air and exhaust required by fireplaces gas furnaces gas water heaters and other naturally vented systems To minimize the chance of interruption of such naturally vented systems follow the heating equipment manufacturer s guidelines and safety standards such as those published by NFPA and A
23. rder ondine today 24 hours every day or by phone at 1 800 661 1616 during normal business hours Instructions contained in this manual cover procedures to be performed by any user Other servicing generally should be referred to qualified service personnel Caution must be exercised since improper servicing may cause unsafe operation Contact Us GEAppliances ca oA If you are not satisfied with the service you receive from Mabe contact us on our Website with all the details y including your phone number or write to General Manager Customer Relations Mabe Canada Inc Suite 310 1 Factory Lane Moncton N B EIC 9M3 Register Your Appliance GEAppliances ca Register your new appliance on line at your convenience Timely product registration will allow for enhanced communication and prompt service under the terms of your warranty should the need arise You may also mail in the pre printed registration card included in the packing material
24. rizontal line indicating the bottom of the hood e Use a level to draw the cooktop centerline location Measure 15 3 8 up from the horizontal line for the bottom of the hood Draw another horizontal line Measure 18 up from the line for the bottom of the hood draw another horizontal line to indicate the top of the hood FOR VERTICAL Straight Up DUCTING If venting out the ceiling extend the centerline forward on the ceiling Measure 6 7 8 from drywall to mark centerline for a 72 dia duct hole on the ceiling If drywall is not present add drywall thickness to the 6 7 8 dimension Venting through a soffit or upper cabinet Follow the same procedure for ceiling ducting to cut the 7v dia hole through the top of the cabinet or soffit See Step 4 page 5 for details to cut opening for duct transition House Wiring Location The junction box is fastened to the back of the hood on the right side See illustrations for hood knockout locations Note The junction box can be relocated to the inside top of the hood House wiring may enter the junction box from the rear or the top of the hood at the right side To route house wiring through the ceiling or soffit Cut a hole approximately 1 dia 5 7 8 forward on the ceiling 11 1 8 to the right of the centerline for 30 models or 14 1 8 to the right of the centerline for 36 models To route house wiring through the wall Cut a
25. t panel 1 1 4 Position the filter in the lower slots at the bottom of the filter support ilter Filters Support JL Ld INSTALL CONTROL KNOBS LIGHT OFF HI To remove the filters grasp the handle push the filter up and pull forward 1 Ft 0 3 m 1 2 5 cm Push control knobs onto the shafts 13 FINALIZE INSTALLATION Refer to the operating instructions to test all controls 18 Safety Instructions Operating Instructions Care and Cleaning Troubleshooting Tips Consumer Support 19 www GEAppliances ca Notes Before you call for service Troubleshooting Tips Save time and money Review the charts on the following pages first and you may not need to call for service Safety Instructions Problem Possible Causes What To Do Fan does not operate A fuse may be blown or a Replace fuse or reset circuit breaker when the switch is on circuit breaker tripped The blower connector is loose Disconnect power to the unit Remove the filters or not plugged into its mating and look up at the blower If the blower connector connector plug is loose or you see the connector dangling the installer failed to plug it in securely Although it is a blind connection it is easy to plug in See the Installation Instructions in this manual for the plug location and ho
26. the date of the During this full one year warranty Mabe will also provide free of charge all labor and original purchase in home service to replace the defective part What Mabe Will Not Cover Service trips to your home to teach you how to use the product Improper installation delivery or maintenance Failure of the product if it is abused misused or used for other than the intended purpose or used commercially Replacement of house fuses or resetting of circuit breakers Damage to the product caused by accident fire floods or acts of God Incidental or consequential damage caused by possible defects with this appliance Damage caused after delivery EXCLUSION OF IMPLIED WARRANTIES Your sole and exclusive remedy is product repair as provided in this Limited Warranty Any implied warranties including the implied warranties of merchantability or fitness for a particular purpose are limited to one year or the shortest period allowed by law This warranty is extended to the original purchaser and any succeeding owner for products purchased for home use within Canada If the product is located in an area where service by a Mabe Authorized Servicer is not available you may be responsible for a trip charge or you may be required to bring the product to an Authorized Mabe Service Location for service Some provinces do not allow the exclusion or limitation of incidental or consequential damages This warranty gives
27. ver to the top of the hood with 4 screws provided To install the 12 duct cover alone Place the 2 piece duct cover on top of the hood Secure the bottom cover to the top of the hood with 4 screws provided See illustration page 16 Extend the inside section upwards to meet the ceiling and ceiling bracket Secure the duct cover to the bracket with the 2 small Phillips screws provided 10 INSTALL FILTER SUPPORT Tip filter support into the rear of the hood Insert support tabs into the slots at the rear of the hood Insert Tabs into Slots Insert 2 Screws Secure the support to the hood with screws as shown 1Ft 0 3m 1 2 5 cm Installation Instructions 11 INSTALL FILTERS Remove protective film covering the filters 11A INSTALL OPTIONAL COMMERCIAL FILTERS Insert the filter into the C clips mounted to the top Remove supplied filters if installed of the vertical front panel Tap the filter against one side to align with outside opening Pull the filter down into the lower slots at the bottom of the filter support Junction Box Place the filter drip trays into the horizontal channel in the filter panel located behind the filters The grease will drain from the filters into these trays e Insert the filter into the C clips mounted to the top of the vertical fron
28. w to plug the connector in Fan fails to circulate air Excessively soiled filters Remove the filters clean if necessary and replace or moves air slower than them If cleaning and replacing the filters does not normal correct the problem call for service Operating Instructions Care and Cleaning A D Q P E Consumer Support 20 Please place in envelope and mail to Veuillez mettre dans une enveloppe et envoyez OWNERSHIP REGISTRATION P O BOX 1780 MISSISSAUGA ONTARIO L4Y 4G1 FOR CANADIAN CONSUMERS ONLY POUR R SIDENTS CANADIENS SEULEMENT 21 OWNERSHIP REGISTRATION CERTIFICATE FICHE D INSCRIPTION DU PROPRI TAIRE Please register your product to enable us to contact you in Veuillez enregistrer votre produit afin de nous permettre de o Ido not wish to receive any promotional offers regarding this product Je ne d sire pas recevoir d offres promotionnelles concemant ce produit 3 1 l if l I l I l i i Y ff the remote event a safety notice is issued for this product communiquer avec vous si jamais un avis de s curit concemant i 25 1 and to allow for efficient communication under the terms of ce produit tait mis et de communiquer facilement avec vous en I amp our warranty should the need arise vertu de votre garantie si le besoin s en fait sentir i pui 1 gt f REGISTER ON LINE
29. ways be vented to the outdoors S o te S READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY CON READ AND SAVE THESE INSTRUCTIONS yoddng 10umnsuo Using the hood controls Throughout this manual features and appearance may vary from your model FAN OFX LIGHT OF Safety Instructions MED LO MED HI Operating Instructions D FAN Control LIGHT Control Turn the FAN speed control to LO MED LO Turn the LIGHT control to HI for bright light MED HI ox HI as needed while cooking Turn to NITE for use as a night light Continuous use of the fan system while cooking helps keep the kitchen comfortable and less humid It also reduces cooking odors and soiling moisture that create a frequent need for cleaning NOTE When the fan is operating on the LO setting it will be very quiet Always make sure that the fan is turned OFF when you are finished in the kitchen Care and Cleaning A D S E Consumer Support Care and cleaning of the vent hood Be sure electrical power is off and all surfaces are cool before cleaning or servicing any part of the vent hood If it ever becomes necessary to replace the metal grease filters they may be ordered from your GE supplier Heavy duty commercial filters may also be used in place of the filters For 30 76 2 cm hoods order Kit no JXBF30SS For 36 91 4 cm hoods order Kit no JXBF36SS To order call 1 800 661 1616
30. you specific legal rights and you may also have other rights which vary from province to province To know what your legal rights are consult your local or provincial consumer affairs office Warrantor Mabe Canada Inc Burlington Ontario 23 suoyonysuy Ajajeg suoijanijsu Guyesadg D c 3 Q e Buiuea sdij Burjooisa qnoa uoddns 10umnsuo Consumer Support GE Appliances Website GEAppliances ca Have a question or need assistance with your appliance Try the GE Appliances Website 24 hours a day any day of the year For greater convenience and faster service you can now download Owner s Manuals order parts or even schedule service ordine Schedule Service GEAppliances ca Expert Mabe repair service is only one step away from your door Get on line and schedule your service at your convenience 24 hours any day of the year Or call 1 800 461 3636 during normal business hours Extended Warranties GEAppliances ca Purchase a GE extended warranty and learn about special discounts that are available while your warranty is still in effect You can purchase it on line anytime or call 1 888 261 2133 during normal business hours Mabe Consumer Home Services will still be there after your warranty expires Parts and Accessories GEAppliances ca Individuals qualified to service their own appliances can have parts or accessories sent directly to their homes VISA MasterCard and Discover cards are accepted O
Download Pdf Manuals
Related Search