GE C4S Installation Guide
Contents
1. GE Lighting Solutions GEH 3894C INSTRUCTIONS Ballast and Optical Asembly for Versaglow Conserva 150 400 and Minimite CONSERVA 150 400 Cis C4s SI MPM 3PR MPM 3PRW ES MPM 3PF READ THOROUGHLY BEFORE INSTALLING A WARNING Risk of electric shock e Turn power off before servicing see instructions GENERAL The ballast assembly optical assembly and hanging hardware are separately packaged Check to insure that unit is not damaged and verify that correct material has been received If the luminaire you ordered has a polycarbonate refractor please pay particular attention to the following statement All polycarbonates and articles made from polycarbonates will yellow with time The rate of yellowing is determined by the specific material any additives and coatings as well as the optical temperature and exposure to ultraviolet UV light This yellowing can reduce the light output and impact resistance of products made from polycarbonates In no ease should the maximum voltage recommendations listed for the luminaire be exceeded Contact factory for more information MOUNTING CAUTION Unit will fall if not installed properly e Follow installation instructions TO ATTACH LUMINAIRE TO SURFACE MOUNTED HANGING HARDWARE MPM C Remove wiring compartment cover plate from hanging hardware Slide luminaire extrusion fully into hanger arna AN2. Replace cover plate The cover plate is necessary to seal wiring chamber and lock luminaire into hanging ardware TO ATTACH LUMINAIRE TO RIGID CONDUIT HANGING HARDWARE MPM 3PRW For Wet Location Enclosed Minimite MMI Minimite MML and Conserva 150 C15 only MPM 3PR Remove cover plate from hanging hardware Slide luminaire extrusion fully into hanger extrusion Replace cover plate Cover plate is necessary to seal wiring chamber and lock luminaire into hanging hardware TO ATTACH LUMINAIRE TO NON RIGID CONDUIT MPM 3PF Use same assembly procedure as for above hanging hardware If an adjustment is necessary to center weight of luminaire in non rigid pendant mounting slightly loosen top screw and slide hub in relation to luminaire until luminaire hangs vertically Re tighten top screw TO ATTACH LUMINAIRE TO JUNCTION BOX MOUNTED HANGING HARDWARE MPM OBC Slide luminaire extrusion full into hanger extrusion When extrusions are properly engaged a click should be heard as spring clip rides over cast protrusion and snaps into place To remove luminaire insert screwdriver blade into hole in spring clip and pull gently downward on handle lifting clip over cast protrusion Grasp luminaire in both hands and withdraw it from hanger TO ATTACH LUMINAIRE TO WALL BRACKET MPM WW TO WALL BRACKET MPM W3TFW STANCHION MOUNT MPM 5ASW MINIMITE OPTICALS ONLY Remove cover plate of mounting bracket Slide luminaire extrusion into hanger extrusion and rep
3. aring it to nameplate Do not remove insulated connectors from wires not needed for required voltage connection When changing voltage on reconnectable units move only the lead with the insulated connector IF SINGLE VOLTAGE All single voltage ballasts are pre wired such that user need only connect the supply conductors IF MULTIVOLT 120 208 240 277 volts Connect the ballast lead with the insulated terminal to the desired voltage terminal as indicated on the ballast terminal nameplate IF MULTIWATT Multiwatt ballasts are available in various combinations of wattage See wiring instructions on wiring tag inside the luminaire Replace reflector plate by reversing above procedure Note Recessed area of plate must close off area around socket Do not flip over when reinstalling Note For multivolt on switched quartz units replace reflector plate with starred hole above capacitor LAMP INSTALLATION Use only lamps specified on nameplate Observe lamp manufacturer s recommendations and restric tions on lamp operation particularly ballast type burning position etc Lamp Tightness The lamp should be securely inserted to NEMA EEI Specified torque or 35 inch pounds which is best achieved by very firmly tightening to insure application of sufficient torque Tightening must be sufficient to fully depress and load center contact of socket Lamp Tightness Medium Base Lamp The lamp should be tightened to a light firmness sufficient
4. desired or should particular problems arise which are not covered sufficiently for the purchaser s purposes the matter should be referred to GE Lighting Solutions GE Lighting Solutions e 1 888 MY GE LED e www gelightingsolutions com 1 888 69 43 533 GE Lighting Solutions is a subsidiary of the General Electric Company Evolve and other trademarks belong to GE Lighting Solutions The GE brand and logo are trademarks of the General Electric Company 2011 GE Lighting Solutions Information provided is subject to change without notice All values are design or typical values when measured under laboratory conditions 35 201578 C4 1 00
5. lace cover plate The cover plate is necessary to seal wiring chamber and lock luminaire into wall bracket INSTALLING OPTICAL ASSEMBLY NOTE For units with clampbands assemble refractor and reflector with clampband and hardware provided CAUTION DO NOT REST A COMPLETE LUMINAIRE ON THE REFRACTOR THIS REFRACTOR IS A PRECISION OPTICAL INSTRUMENT AND WILL NOT SUPPORT THE FULL WEIGHT OF THE LUMINAIRE VERSAGLOW 150 250 CONSERVA 150 400 After hanging hardware ballast assembly and lamp have been properly installed according to their instructions hook latches on ballast assembly to tabs on optical assembly Snap retaining latches to upward position to complete installation MINIMITE After hanging hardware ballast assembly and lamp have been properly installed according to their instructions pull down three latches and slip spring loops over hooks In the case of hook which acts as a hinge the flat spring must be bent slightly to allow loop to be released MPM OBC MMI MML MPM SASW MPM W3TFW MPM WW WIRING For certain voltages open unit through reflector plate by loosening three screws rotating plate with a small screwdriver in slot provided and lifting plate On some units unit is opened by completely removing screws Wire per instructions Make all electrical connections in accordance with the National Electrical Code and any applicable local coderequirements Verify that supply voltage is correct by comp
6. to depress the center contact SWITCHED QUARTZ The switched quartz socket is secured for shipping inside main lamp socket Remove align and snap into starred hole provided in reflector plate Install quartz lamp not provided When reflector plate is removed for multivolt units replace with starred hole above capacitor MAINTENANCE AND CLEANING CAUTION Risk of burn e Allow lamp fixture to cool before handling It will occasionally be necessary to clean outside of refractor to maintain light levels Frequency of cleaning will depend on ambient dirt level and minimum light levels acceptable to user The refractor should be washed in a solution of warm water and any mild non abrasive household detergent Wipe with soft cloth or brush Rinse in cool clear water Should the optical assembly become dirty on inside clean in above manner and replace any damaged gasket Use of abrasive cleaners will shorten life of refractor and refractor The light output of a luminaire is also dependent on age of lamp In applications where light level is critical it may be desirable to replace lamps before they burn out The lamp manufacturer can provide data showing how lamp light output decreases with use These instructions do not purport to cover all details or variations in equipment nor to provide for every possible contingency to be metin connection with installation operation or maintenance Should further information be
Download Pdf Manuals
Related Search