Garmin AiS 300 Blackbox Receiver Installation Instructions
Contents
1. INDIRECT OR CONSEQUENTIAL DAMAGES INCLUDING WITHOUT LIMITATION DAMAGES FOR ANY TRAFFIC FINES OR CITATIONS WHETHER RESULTING FROM THE USE MISUSE OR INABILITY TO USE THE PRODUCT OR FROM DEFECTS IN THE PRODUCT SOME STATES DO NOT ALLOW THE EXCLUSION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU Garmin retains the exclusive right to repair or replace with a new or newly overhauled replacement product the device or software or offer a full refund of the purchase price at its sole discretion SUCH REMEDY SHALL BE YOUR SOLE AND EXCLUSIVE REMEDY FOR ANY BREACH OF WARRANTY To obtain warranty service contact your local Garmin authorized dealer or call Garmin Product Support for shipping instructions and an RMA tracking number Securely pack the device and a copy of the original sales receipt which is required as the proof of purchase for warranty repairs Write the tracking number clearly on the outside of the package Send the device freight charges prepaid to any Garmin warranty service station Online Auction Purchases Products purchased through online auctions are not eligible for warranty coverage Online auction confirmations are not accepted for warranty verification To obtain warranty service an original or copy of the sales receipt from the AIS 300 Installation Instructions 7 original retailer is required Garmin will not replace missing components from any package purchased through an online aucti2. yellow wire from the AIS 300 power data cable to the Accessory On wire from the chartplotter The AIS 300 will then turn on or off with the Garmin chartplotter e Ifthe AIS 300 is connected to a non Garmin NMEA 0183 chartplotter or not connected to a chartplotter at all then you must install a toggle switch to turn the device on and off o Connect the yellow wire from the AIS 300 power data cable to one terminal of a single pole single throw switch not included and connect the other switch terminal to the negative battery terminal o When you close the switch the AIS 300 powers on When you open the switch the AIS 300 powers off Connecting a VHF Antenna to the AIS 300 To transmit and receive AIS information the AIS 300 must be connected to a VHF antenna not included Connect a marine VHF antenna to the AIS 300 using the antenna port on the device If you have a VHF radio on your boat connect the VHF radio to the AIS 300 using the included RF interconnect cable according to the wiring layout diagrams starting on page 2 Mount the antenna according to the installation instructions provided with the antenna Connecting the AIS 300 to a NMEA 2000 Network Optional You can connect the AIS 300 to a NMEA 2000 compliant chartplotter using your existing NMEA 2000 network or you can build a basic NMEA 2000 network if you do not have one on your boat For more information on NMEA 2000 and to purchase required cables and connectors go
3. A GARMIN AlS 300 Installation Instructions Use these instructions to install the Garmin AIS 300 Automatic Identification System AIS Class B receiver device Compare the contents of this package with the packing list on the box If any pieces are missing contact your Garmin dealer immediately Use the following instructions to install the AIS 300 device Details for the following steps are included in this document Select locations for the AIS components Mount the AIS 300 receiver box Connect the AIS 300 to power Connect the AIS 300 to a VHF antenna and to an optional VHF radio page 4 Connect the AIS 300 to a NMEA 2000 network or to a NMEA 0183 compatible chartplotter optional page 4 or N When navigating carefully compare information provided by the unit to all available navigation sources including information from visual sightings local waterway rules and restrictions and maps For safety always resolve any discrepancies or questions before continuing navigation Use this unit only as a navigational aid Do not attempt to use the unit for any purpose requiring precise measurement of direction distance location or topography Wear safety goggles and a dust mask when drilling cutting or sanding Safe Compass Distance Ensure that you install the AIS 300 receiver box at least 15 3 4 in 40 cm from any compass Test your compass to verify that it operates correctly when the AIS 300 is opera
4. arge to the customer for parts or labor provided that the customer shall be responsible for any transportation cost This warranty does not apply to i cosmetic damage such as scratches nicks and dents ii consumable parts such as batteries unless product damage has occurred due to a defect in materials or workmanship iii damage caused by accident abuse misuse water flood fire or other acts of nature or external causes iv damage caused by service performed by anyone who is not an authorized service provider of Garmin or v damage to a product that has been modified or altered without the written permission of Garmin In addition Garmin reserves the right to refuse warranty claims against products or services that are obtained and or used in contravention of the laws of any country This product is intended to be used only as a travel aid and must not be used for any purpose requiring precise measurement of direction distance location or topography Garmin makes no warranty as to the accuracy or completeness of map data in this product THE WARRANTIES AND REMEDIES CONTAINED HEREIN ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES EXPRESS IMPLIED OR STATUTORY INCLUDING ANY LIABILITY ARISING UNDER ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE STATUTORY OR OTHERWISE THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS WHICH MAY VARY FROM STATE TO STATE IN NO EVENT SHALL GARMIN BE LIABLE FOR ANY INCIDENTAL SPECIAL
5. ct cable 7 included Hy EN E included GARMIN st 2 VHF radio ES m T optional not O x included QO J Q Q lt 2 S g QO amp i GPSmap 4012 S S 5 7 j 8 5 U 9 Q Chartplotter x n xs power 1 S o 3 Chartplotter ZE optional not E included J L E dh 12 or 24 Vdc The AIS 300 does not need to be installed alongside a VHF radio but they can share the same VHF antenna if they are both installed on your boat AIS 300 Installation Instructions AIS 300 Wiring Layout AIS 300 Connected to a Garmin Chartplotter Through NMEA 0183 VHF radio optional not included oO S st ws I RF interconnect p cable included Wire color function Wire color function O SE Gray Tx A White RxA O ee Orange White Rx B Orange AIS 300 power data cable Accessory On Q 2 a Chartplotter power N gt GPSmap 4012 Garmin NMEA 0183 U compatible chartplotter optional not included GARMIN 12 or 24 Vdc The AIS 300 does not need to be installed alongside a VHF radio but they can share the same VHF ant
6. enna if they are both installed on your boat The listed wire colors are for the NMEA 0183 Port 1 input on a Garmin GPSMAP 4000 5000 or GPSMAP 6000 7000 series chartplotter Refer to the installation instructions provided with your Garmin chartplotter if you want to connect the AIS 300 to a different model of Garmin chartplotter or to a different NMEA 0183 port on a GPSMAP 4000 5000 or GPSMAP 6000 7000 series chartplotter If you are connecting the AIS 300 to a non garmin chartplotter see page 5 for detailed wiring assignments AIS 300 Installation Instructions Connecting the Receiver Box to Power Use the AIS 300 power data cable to connect the receiver box to a 12 or 24 Vdc battery Notes e Connect the red wire to the positive battery terminal and connect the black wire to the negative battery terminal e The replacement fuse on the power data wiring harness is a 5 A fast acting fuse e Ifit is necessary to extend the power wires use 16 AWG or larger wire Installing the AIS 300 Power Toggle The AIS 300 can be powered on and off in one of 3 ways e Ifthe AIS 300 is connected to a NMEA 2000 network it will turn on and off with the NMEA 2000 network NOTE The AIS 300 is not powered by the NMEA 2000 network however it will turn on when it detects power on the NMEA 2000 network You must connect the AIS 300 to power as well as to the NMEA 2000 network e Ifthe AIS 300 is connected to a Garmin chartplotter using NMEA 0183 connect the
7. ions However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and the receiver e Connect the equipment into an outlet that is on a different circuit from the GPS unit e Consult the dealer or an experienced radio TV technician for help This product does not contain any user serviceable parts Repairs should only be made by an authorized Garmin service center Unauthorized repairs or modifications could result in permanent damage to the equipment and void your warranty and your authority to operate this device under Part 15 regulations Declaration of Conformity DoC Hereby Garmin declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC To view the full Declaration of Conformity go to www garmin com compliance Limited Warranty This Garmin product is warranted to be free from defects in materials or workmanship for one year from the date of purchase Within this period Garmin will at its sole option repair or replace any components that fail in normal use Such repairs or replacement will be made at no ch
8. n 40 cm Waterproof Rating IEC 60529 IPX7 Immersion in meter of standing water for 30 minutes Power Source 9 6 31 2 Vde 12 Vdc or 24 Vdc boat battery Usage 2 5 W max Fuse 5 A fast acting NMEA 2000 Power Usage LEN 2 8 5 22 in 207 mm _ 7 Antenna Antenna Connector PL259 Antenna Port Impedance 50 Q Bf GARMIN NMEA 2000 PGN Information Receive Transmit 059392 ISO Acknowledgment 059392 ISO Acknowledgment 059904 ISO Request 060928 ISO Address Claim 060928 ISO Address Claim 126208 NMEA Request Command Acknowledge Group Function 126208 NMEA Command Request Acknowledge Group Function 126464 PGN List 126992 System Time 126996 Product Information 129038 AIS Class A Position Report 129039 AIS Class B Position Report 129040 AIS Class B Extended Position Report The Garmin AIS 300 is NMEA 2000 certified 129794 AIS Class A Static and Voyage Related Data U 129798 AIS SAR Aircraft Position Report 129802 AIS Safety Related Broadcast Message 129809 AIS Class B CS Static Data Report Part A 129810 AIS Class B CS Static Data Report Part B NMEA 0183 Communication Information When connected to a NMEA 0183 device the AIS 300 transmits the VDM sentence Product Registration Help
9. ompliant device to identify the receiving RX A and B wires e If your NMEA 0183 compliant device has only one receiving wire Rx connect it to the gray wire Tx A from the AIS 300 and leave the pink wire Tx B wire unconnected e The AIS 300 can transmit NMEA 0183 data using either 38400 baud default or 4800 baud Connect the orange white wire from the AIS 300 power data cable to the negative battery terminal if you would like to limit the output speed to 4800 baud Refer to the documentation provided with your chartplotter to determine the correct NMEA 0183 baud rate Using the AIS 300 If you connected the AIS 300 to a chartplotter using either NMEA 2000 or NMEA 0183 refer to the Owner s Manual provided with your chartplotter for information on using the AIS specific features of the chartplotter If you did not connect the AIS 300 to a Garmin chartplotter ensure that you connected a power toggle switch using the yellow wire on the AIS 300 power data cable see page 4 When you want to turn on the AIS 300 close the switch When you want to turn off the AIS 300 open the switch AIS 300 Installation Instructions 5 Appendix 5 17 32 in Specifications mi 140 6 mm Dimensions W x H x D 8 5 32 x 5 17 32 X 1 25 3 in 207 x 140 6 x 45 7 mm Weight lb 7 6 oz 670 g i Temperature Range from 4 F to 158 F from 20 C to 70 C P Compass safe Distance 15 3 4 i
10. on International Purchases A separate warranty may be provided by international distributors for devices purchased outside the United States depending on the country If applicable this warranty is provided by the local in country distributor and this distributor provides local service for your device Distributor warranties are only valid in the area of intended distribution Devices purchased in the United States or Canada must be returned to the Garmin service center in the United Kingdom the United States Canada or Taiwan for service Australian Purchases Our goods come with guarantees that cannot be excluded under the Australian Consumer Law You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure The benefits under our Limited Warranty are in addition to other rights and remedies under applicable law in relation to the products Garmin Australasia Unit 19 167 Prospect Highway Seven Hills NSW Australia 2147 Phone 1800 822 235 Garmin s Marine Warranty Policy Certain Garmin Marine products in certain areas have a longer warranty period and additional terms and conditions Go to www garmin com support warranty html for more details and to see if your product is covered under Garmin s Marine Warran
11. ting Selecting Locations for the AIS 300 Components Use the wiring layout diagrams starting on page 2 to determine how to best organize the AIS 300 components on your boat Ensure that the cables reach all components before permanently mounting any component Mounting the AIS 300 Receiver Box Install the AIS 300 receiver box below deck on a bulkhead Select a location that is dry and protected from washdown Ensure that the location is well ventilated and away from objects that generate heat Ensure that the receiver box is at least 15 3 4 in 40 cm from any compass to avoid interference Needed Tools Drill and drill bits e Number 2 Phillips screwdriver To mount the receiver box 1 Ensure that the chosen location is dry protected from washdown and well ventilated Use the receiver box as a template and use a pencil to mark the holes in the four corners Do not drill through the receiver box Drill four 1 s in 3 mm pilot holes A Ww N Mount the receiver box using the included 20 mm M 3 5 screws You can also use bolts washers and nuts not included to mount the receiver box if the mounting surface is suitable September 2013 190 01178 00 Rev D Printed in China AIS 300 Wiring Layout AIS 300 Connected to a Garmin Chartplotter Through NMEA 2000 RF cable to VHF antenna not included J MUL s NMEA 2000 drop cable RF interconne
12. to www garmin com The AIS 300 wiring layout diagram on page 2 contains an example of the AIS 300 connected to a Garmin chartplotter through a NMEA 2000 network NOTE If you are unfamiliar with NMEA 2000 see the NMEA 2000 Network Fundamentals chapter in the Technical Reference for Garmin NMEA 2000 Products for more information Visit www garmin com products AIS300 and click on Manuals on the AIS 300 page 4 AIS 300 Installation Instructions Connecting the AIS 300 to a NMEA 0183 Device Optional You can connect the AIS 300 to a NMEA 0183 compliant chartplotter using the bare wires on the AIS 300 power data cable Connect NMEA 0183 bare wires to a Garmin chartplotter as indicated in the wiring layout diagram on page 3 Consult the diagram below to connect the AIS 300 to a non Garmin chartplotter Use 22 AWG wire for extended runs of NMEA 0183 wire if needed If it is necessary to extend the power wires use 16 AWG or larger wire AIS 300 receiver box Battery 12 or 24 Vdc Wire function Wire color function Fuse 5A Redjpower Power Black ground NMEA 0183 Yellow compliant i chartplotter E power toggle page 4 4 Unconnected 38400 high speed Orange white Connected to battery negative 4800 standard speed speed select Connecting the AIS 300 to a Non Garmin NMEA 0183 Device Notes Consult the installation instructions for your NMEA 0183 c
13. ty Policy 2010 Garmin Ltd or its subsidiaries Garmin the Garmin logo and GPSMAP are trademarks of Garmin Ltd or its subsidiaries registered in the USA and other countries These trademarks may not be used without the express permission of Garmin NMEA 2000 and the NMEA 2000 logo are registered trademarks of the National Marine Electronics Association For the latest free software updates excluding map data throughout the life of your Garmin products visit the Garmin Web site at www garmin com A we a TA 2012 1367 ICIS A GARMIN Sperone 2010 Garmin Ltd or its subsidiaries Garmin International Inc 1200 East 151 Street Olathe Kansas 66062 USA Garmin Europe Ltd Liberty House Hounsdown Business Park Southampton Hampshire SO40 9LR UK Garmin Corporation No 68 Zhangshu 2 Road Xizhi Dist New Taipei City 221 Taiwan R O C www garmin com September 2013 190 01178 00 Rev D Printed in China
14. us better support you by completing our online registration today Go to http my garmin com Keep the original sales receipt or a photocopy in a safe place Contact Garmin Contact Garmin Product Support if you have any questions while using the AIS 300 In the USA go to www garmin com support or contact Garmin USA by phone at 913 397 8200 or 800 800 1020 In the UK contact Garmin Europe Ltd by phone at 0808 2380000 In Europe go to www garmin com support and click Contact Support for in country support information or contact Garmin Europe Ltd by phone at 44 0 870 8501241 6 AIS 300 Installation Instructions Industry Canada Compliance This device complies with Industry Canada Standard RSS 182 and ICES 003 FCC Compliance This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and may cause harmful interference to radio communications if not installed and used in accordance with the instruct
Download Pdf Manuals
Related Search