Garmin 190-01554-00_0C User's Manual
Contents
1. 1 Place the collar around the middle of the dog s neck 2 Position the device at the front of the dog s neck with the status LED facing towards the dog s chin and the contact points against the throat TIP The device contact points should be positioned near the dog s vocal cords This location varies based on the breed of dog If the device does not seem to detect the dog s barks you should move the device closer to or further from the dog s body to find the ideal location Tighten the strap so that it is very snug around the dog s neck and fasten the buckle NOTE The collar should fit tightly and should not be able to rotate or slide on the dog s neck The dog must be able to swallow food and water normally You should observe your dog s behavior to verify that the collar is not too tight o 4 Wiggle the device to work the contact points through the dog s coat NOTE The contact points must have contact with the dog s skin to effectively detect and correct barks 5 If the strap is too long cut off the excess leaving at least 3 in 8 cm to spare TIP You can mark the hole used to fasten the buckle for future reference Changing the Bark Correction Mode and Intensity Level Rotate the dial to select an option e To correct using vibration select V page 2 To correct using automatic intensity select A page 2 e To correct using a set intensity level select 1 to 7 page 2 A higher number indicate2. 2 e Wiggle the device to work the contact points through the dog s coat Gradually increase the intensity level page 2 Device Information BarkLimiter Specifications Battery type User replaceable 3V CR2 lithium cylindrical Battery life 6 months typical use Operating temperature From 5 to 140 F from 15 to 60 C range Water resistance IPX7 BarkLimiter Deluxe Specifications Battery type Rechargeable replaceable lithium ion Battery life 3 months typical use Operating temperature range From 5 to 140 F from 15 to 60 C Charging temperature range From 32 to 104 F from 0 to 40 C Storage temperature range up to 1 month From 4 to 122 F from 20 to 50 C Storage temperature range up to 3 months From 4 to 104 F from 20 to 40 C Storage temperature range up to 1 year From 4 to 68 F from 20 to 20 C Water resistance IPX7 Sleep Mode To conserve battery life the device goes into sleep mode when no barks or motion are detected The activity level of your dog affects the battery life of the device Checking the Battery Charge Level Rotate the dial away from N The color of the status LED indicates the battery charge level for five seconds Green The battery has a good charge Yellow The battery should be charged or replaced soon Red The battery should be charged or replaced im
3. A GARMIN BarkLimiter Series Owner s Manual May 2013 190 01554 00_0C Printed in Taiwan All rights reserved Under the copyright laws this manual may not be copied in whole or in part without the written consent of Garmin Garmin reserves the right to change or improve its products and to make changes in the content of this manual without obligation to notify any person or organization of such changes or improvements Go to www garmin com for current updates and supplemental information concerning the use of this product Garmin and the Garmin logo are trademarks of Garmin Ltd or its subsidiaries registered in the USA and other countries BarkLimiter and Bark Odometer are trademarks of Garmin Ltd or its subsidiaries These trademarks may not be used without the express permission of Garmin Introduction See the Important Safety and Product Information guide in the product box for product warnings and other important information Device Overviews BarkLimiter Device O Contact points Mode and intensity dial Status LED BarkLimiter Deluxe Device Contact points Mode and intensity dial Status LED Charging clip contacts BarkLimiter Deluxe model only SHOTS TS Attaching the Dog Collar Device to the Collar Strap 1 With the buckle facing outward insert the end of the collar strap through the slot on the collar device 2 Pull approximately
4. are aligned with no gaps 8 Tighten the screws evenly Getting More Information You can find more information about this product on the Garmin website e Go to www garmin com outdoor e Go to www garmin com learningcenter e Go to http buy garmin com or contact your Garmin dealer for information about optional accessories and replacement parts Registering Your Device Help us better support you by completing our online registration today Go to http my garmin com Keep the original sales receipt or a photocopy in a safe place Device Information www garmin com support 913 397 8200 0808 238 0000 1 800 800 1020 44 870 850 1242 g 32 2 67252 54 45 4810 5050 49 0 180 6 427646 E 39 02 36 699699 00800 4412 454 lA Hanes Dis EN 35 1214 447 460 Garmin International Inc 1200 East 151st Street Olathe Kansas 66062 USA Garmin Europe Ltd Liberty House Hounsdown Business Park Southampton Hampshire SO40 9LR UK Garmin Corporation No 68 Zhangshu 2nd Road Xizhi Dist New Taipei City 221 Taiwan R O C 1 866 429 9296 aan 358 9 6937 9758 0200 023 3937 035 539 3727 m 34 93 275 44 97 2013 Garmin Ltd or its subsidiaries 43 0 820 220 230 331 55 69 33 99 47 815 69 555 46 7744 52020 MN ill CE
5. atteries Contact your local waste disposal department to properly recycle the batteries Device Information wo BarkLimiter Deluxe Components Battery assembly Gasket Battery connector Device 0100 0e Security screws Replacing the BarkLimiter Deluxe Battery Assembly Before you replace the battery you must remove all dirt water and debris from the device You also need the security screwdriver included with the new battery assembly You can purchase a replacement battery assembly at http buy garmin com or from your Garmin dealer The battery assembly includes a pre assembled back plate with a gasket battery and battery connector 1 Remove the four security screws from the corners of the device 2 Lift up the battery assembly 3 Disconnect the battery connector from the device TIP You should grip the wires close to the connector and pull the connector outward from the circuit board 4 With the new battery assembly connect the battery connector to the device When properly installed the connector plug snaps into the port and the top face of the connector plug is flush with the edges of the port 5 Verify that the gasket is not damaged and that it is completely seated in the groove 6 Hold the battery assembly and the device firmly together and replace all four security screws without tightening 7 Verify that the battery assembly and the device
6. mediately Bark correction features are disabled BarkLimiter Battery Replacement Instructions Do not use a sharp object to remove batteries Contact your local waste disposal department to properly recycle the batteries BarkLimiter Components 3 O O j O ES O O Back plate Gasket Battery 0 Polarity indicators Replacing the BarkLimiter Battery Before you replace the battery you must remove all dirt water and debris from the device You also need a small Phillips screwdriver You must replace the battery with a 3V CR2 lithium battery 1 Remove the four screws from the corners of the back plate 2 Remove the back plate The battery comes out with the back plate Remove the battery Install the new battery into the back plate according to the polarity indicators engraved on the back plate When properly installed the battery snaps into the back plate Verify that the gasket is not damaged and that it is completely seated in the groove 6 Replace the back plate 7 Replace the four screws to secure the back plate Ro a BarkLimiter Deluxe Battery Replacement Instructions This product contains a lithium ion battery To prevent the possibility of personal injury or product damage caused by battery exposure to extreme heat store the device out of direct sunlight Do not use a sharp object to remove b
7. nd motion or vibration Turning Off the Dog Collar Device Rotate the dial to N Rotating the Dial NOTICE Do not over rotate the dial The dial does not rotate past 7 The dial is intentionally difficult to rotate This helps to prevent accidental rotation while the device is in use on the dog Insert a coin or similar object into the slot to rotate the dial Bark Correction When the device is active and properly fitted on the dog it detects and corrects barks automatically You can adjust the method and intensity of the corrections The status LED flashes briefly when the device detects motion or corrects a bark Short flash Long flash Motion was detected and no correction was applied A bark was detected and a correction was applied Introduction Fitting the Collar on Your Dog To prevent irritation from the contact points remove the collar for at least eight hours out of every 24 hour period This device is not intended for human use Do not attempt to use on any person NOTICE Before you put the collar on the dog remove the charging clip If you do not remove the clip it may become detached from the collar and become lost In order to properly detect and correct barks the collar and device must fit the dog properly If the collar is too loose or positioned incorrectly bark corrections may be inconsistent This can delay or prevent the dog from learning not to bark
8. s a higher intensity level Vibration The device can use a short vibration to correct the dog When using vibration no electrical stimulation is used Automatic Intensity The device can set the stimulation intensity level automatically based on the barking behavior of the dog The device starts at the lowest intensity level and increases the intensity level gradually until the dog stops barking When the dog is quiet the intensity decreases over time The automatic intensity feature is designed to eliminate excessive nuisance barking To stop barks more immediately you should set the intensity level manually Choosing the Correct Intensity Level To prevent irritation from the contact points remove the collar for at least eight hours out of every 24 hour period You can set the stimulation intensity level manually from 1 to 7 You should choose the lowest intensity level that discourages the dog from barking If you have never used a bark correction collar with the dog the dog requires time and experience to learn that the bark is the cause of the stimulation 1 Set the intensity to the lowest level 2 For thirty minutes when the dog barks observe the dog for a reaction such as a head shake neck movement a change in the way the dog barks or just a change in expression 3 If there is no reaction increase the intensity by one level until the dog has a slight but recognizable reaction to the stimulation 4 Allow 24 ho
9. two thirds of the collar strap through the slot 3 Insert the end of the collar strap through the slot on the opposite side of the device 4 Pull the strap until it is tight across the front of the device Charging the BarkLimiter Deluxe Device NOTICE To prevent corrosion thoroughly dry the contacts on the collar and the surrounding area before connecting the charging clip Before you put the collar on the dog remove the charging clip If you do not remove the clip it may become detached from the collar and become lost You should fully charge the battery before you use the device for the first time Charging a fully depleted battery takes about two hours The device will not charge when outside the temperature range of 32 to 104 F 0 to 40 C 1 Snap the charging clip onto the device 2 Plug the small end of the power cable into the mini USB port on the charging clip 3 Plug the other end of the power cable into a power source The status LED is solid red when the collar is charging 4 After the status LED turns solid green remove the charging clip from the collar Turning On the Dog Collar Device Rotate the dial away from N There is a 30 second delay before the device becomes active The status LED indicates the battery charge level for five seconds and turns off After an additional 25 seconds the unit is active The status LED flashes occasionally to indicate that the unit is detecting sou
10. urs for the dog to learn to respond by not barking 5 If the dog continues barking while wearing the collar increase the intensity level gradually until you find the level that discourages the dog from barking Bark Odometer When you turn off the device the LED flashes red and green to report the number of times the device detected a bark since it was last turned on This can help you track your dog s barking behavior Red flash Green flash 10 barks 1 bark For example one red flash followed by four green flashes indicates the device detected 14 barks Checking the Bark Odometer 1 Remove the device from the dog 2 Position the device so that you can see the status LED 3 Rotate the dial to N 4 Count the red and green flashes Troubleshooting My device does not seem to be active When the device is active the status LED flashes only when the device detects a bark or motion e Verify the collar is turned on page 1 e Verify the battery is not low page 3 Remove the device from the dog and shake the device briefly When the device is active the device detects the motion and the status LED flashes Troubleshooting My dog is still barking If the dog continues barking while wearing the device you can try any of these options to improve the effectiveness of the device e Tighten the collar until it is very snug page 2 e Adjust the position of the device on the dog s neck page
Download Pdf Manuals
Related Search