Gaggenau AW 201-790 User's Manual
Contents
1. Fig 7 O The Int key for the intensive level should be pressed when browning and frying in an open pan see Fig 6 If you have switched on the hood by selecting the intensive level it will be switched off again automatically after 5 minutes If you press the Int key while the hood is running at fan level 1 2 or 3 the electronic control will switch back automatically to the previously selected fan level after 5 minutes see Fig 7 If you would like to end the intensive level before the five minutes have elapsed press the 0 key Motor off or select a different level see Fig 8 It is possible to switch off the extraction function at any time by pressing the 0 key motor off Special functions Intensive time You can set the intensive level running time to 3 5 or 10 minutes by simultaneously pressing the Int key and the 1 2 or 3 key and you can store this setting see Fig 9 When delivered the appliance is set to five minutes i e the combination of the Int key and the key 2 Delayed shut off Delayed shut off is possible at any level First press the required key 1 2 3 or Int and then press the key see Fig 10 The delayed shut off time for all levels is ten minu tes After these ten minutes the ventilation switches off but the lighting stays on Interval ventilation Interval ventilation is a special feature of this appl2. Insert the lamp in the lampholder Note do not touch the halogen lamps with your hands Use a cloth and touch the lamp only on its edges Engage the lamp cover Connect the appliance to the mains again 6 Assembly instructions WARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK OR INJURY TO PERSONS OBSERVE THE FOLLOWING a Installation work and electrical wiring must be done by qualified person s in accordance with all applicable codes and standards including fire rated construction b Sufficient air is needed for proper combustion end exhausting of gases through the flue chimney of fuel burning equipment to prevent back drafting Follow the heating equipment manufacturer s guideline and safety standards such as those published by the National Fire Protection Association NFPA and the American Society for Heating Refrigeration and Air Conditioning ASHRAB and the local code authorities c When cutting or drilling into wall or ceiling do not damage electrical wiring and other hidden utilities d Ducted fans must always be vented to the outdoors e If this unit is to be installed over a tub or shower it must be marked as appropriate for the appli cation and be connected to a GFCI Ground Fault Circuit Interrupter protected branch circuit f NEVER place a switch where it can be reached from a tub or shower WARNING To reduce the risk of fire use only metal ductwork 6 1
3. as possible the pipes are not laid at an acute angle but as bends and that they are inserted into the shaft at an inclined upward angle and there are no cross sectional constrictions in the upward direction this reduces the volume flow If long rough exhaust air pipes many pipe bends or smaller pipe diameters are used the air extraction rate will no longer be at an optimum level and there will be an increase in noise The manufacturer of the extractor hood accepts no liability for complaints which can be attributed to the design and layout of the pipework As standard the blow out opening of the extractor hood is in the upward direction To pass exhaust air through the outer wall we recommend the use of our telescopic wall box TM 150 045 6 150 mm Note To prevent the ingress of water e g condensate or rain water from an uncovered exhaust air shaft our condensate separator RV 060 150 must be installed in the exhaust air line The condensate separator must still be accessible after installation The duct units listed below are available depending on the height of the ceiling Installation accessories for exhaust air mode Stainless steel design ventilation duct LK 010 012 for ceiling heights of 7 4 8 6 LK 010 022 for ceiling heights of 8 6 9 9 Aluminium design ventilation duct LK 011 012 for ceiling heights of 7 47 8767 LK 011 022 for ceiling heights of 8 6 9
4. 9 Installation accessories for circulating air mode Stainless steel design ventilation duct LK 010 112 for ceiling heights of 7 7 8 6 LK 010 122 for ceiling heights of 8 67 9 9 Aluminium design ventilation duct LK 011 112 for ceiling heights of 7 7 8 6 LK 011 122 for ceiling heights of 8 6 9 9 The dimensions above refer to a distance of 5 3 from the floor to the bottom edge of the hood If required custom made duct units are available at an extra charge The socket must be placed behind the duct cover on the wall To use above gas cooker gas hob Important do not use all bumers on the highest setting simultaneously over a longer period of time max 15 minutes This will pose a risk of burns when touching the hot appliance exterior or parts of the extractor hood may become damaged Switch the extractor hood to the highest setting when three or more bumers of a gas cooker are used simultaneously 15 Fig 20 16 2 ie 12 5h6 mi 90000880 Important before marking the securing holes make sure that no electricity or water lines or other lines are laid at the drilling points in the wall Proceed as follows From the bottom edge of the hood mark a center line on the wall With the aid of the drilling template mark the positions of the screws on the wall Fig 19 Note this hood has been approved for installations as l
5. Operating and Assembly Instructions AW 200 790 AW 201 790 Extractor Hood DOOQO ODO GAGGENAU AW 200 790 AW 201 790 Preface Safety notes 1 Important notes 1 1 For your safety 1 2 Operating for the first time 1 3 About use 2 Features 3 Operation 4 Cleaning and care 5 Maintenance 6 Assembly instructions 6 1 Technical data 6 2 Installation Page 3 Page 4 5 Page 4 Page 5 Page 5 Page 6 Page 7 9 Page 10 11 Page 12 Page 13 18 Page 13 Page 14 18 Preface Fig 1 With your new extractor hood working in the kitchen will be even more fun The appliance offers you a number of advantages a good extraction capacity with low noise values a large number of control functions optimum illumination of the cooking surface by a dimmable halogen light To ensure that you will be able to use this appli ance in all its diversity read through the operating and assembly instructions conscientiously before operating it for the first time The instructions contain important notes on use installation and maintenance of the appliance On the following page you will find important notes on safety and operation These will serve to ensure your personal safety and the lasting va
6. Technical data Max weight depending on version 28 5kg Dimensions 353 8 x 22 Electrical connection Pay attention to the rating plate data The appliance must only be connected by an authorised specialist The specialist is respon sible for perfect functioning of the appliance at its installation location He must explain the operating principle of the appliance to the user with refe rence to the operating instructions He must explain to the user how the appliance can be isolated from the mains whenever required Connection possibilities The plug of the connecting cable is inserted into the socket that is located behind the duct cover on the wall If this is not possible the disconnection of all the poles of the appliance from the mains must be achieved by way of the domestic fuse or by using an accessible disconnecting device with a contact gap of at least 3 0 mm 13 6 2 Installation The applicable regulations of the energy supply companies and the regional construction regulations must be observed when installing the hood This hood has been approved for installations as low as 30 and as high as 36 above the cooktop The hood can be used in the exhaust or circulating air mode The exhaust air can be routed into a separate exhaust air shaft or directly into the open through the outside wall It is not allowed to pass the exhaust air into a flue or exhaust air chimney that is in operation or into a sha
7. ft that is linked to the heating basement Consult the chimney sweep responsible for your district whenever you wish to pass the exhaust air into a chimney that is not in operation During the course of planning a chimney sweep must be consulted if a room au dependent hearth is operated in the same room as the one in whicha hood is operated in the exhaust air mode Adequate incoming air must be ensured The applicable construction and safety regulations must be observed Adequate incoming air must be ensured if a wood coal gas or oil heater or an open hearth is operated in the same room as the one in which the hood is installed Safe operation is possible whenever the partial vacuum in the place where the firing equipment is installed does not exceed 4 Pa 0 04 mbar This can be achieved whenever the air needed for combustion is able to enter through openings that cannot be sealed for example in doors windows incoming exhaust air wall boxes or other technical means 14 hood height 514 251 2 Fig 18 53 lt 74 9 9 ceiling height Flexible aluminium pipes corrosion protected sheet metal pipes and exhaust air pipes whose material conforms to fire B1 in accordance with DIN 4102 can be used Exhaust air pipes should have a nominal diameter of 6 150 mm Pay particular attention to ensuring that the exhaust air ducts and pipes are kept as short
8. iance which periodically activates the fan for five minutes every hour You can activate this function by simultaneously pressing the 0 key and depending on the required extraction capacity the 1 2 or 3 key see Fig 11 This mode of operation is indicated by alternating illumination of the key together with the corresponding fan level indicator You can switch off interval ventilation by pressing the 0 key see Fig 12 4 Cleaning and care TZ TRE P Fig 13 amp Fig 14 10 Cleaning the grease filters The grease filter saturation display F flashes after an operating time of 30 hours to you indicate to you that you should clean the grease filter see Fig 3 The grease filters can of course be cleaned at any time even if the grease filter saturation display has not started to flash The stainless steel grease filters can be removed easily for cleaning see Fig 13 Disconnect the power supply switch off the fuse Grip the grease filter handle and push the slide towards the rear Then pull the grease filter downwards out of the holder repeat the operation for the other grease filters You can clean the stainless steel grease filters ina dishwasher at a maximum temperature of 130 F 55 C where it should be suppo
9. lue of your appliance You will find notes on page 4 that you ought to observe before operating the appliance for the first time The chapters entitled Structure and operating principle and Operation will tell you all the things your extractor hood is capable of doing and how the appliance is operated Tips and hints in the chapter entitled Cleaning and care will make sure that your appliance will stay operable and beautiful for a long time And now we wish you lots of fun with your new extractor hood safety notes Read And Save These Instructions WARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK OR INJURY TO PERSONS OBSERVE THE FOLLOWING a Use this unit only in the manner intended by the manufacturer If you have questions contact the manufacturer b Before servicing or cleaning unit switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally When the service disconnecting means cannot be locked securely fasten a prominent warning device such as a tag to the service panel CAUTION FOR GENERAL VENTILATION USE ONLY DO NOT USE TO EXHAUST HAZARDOUS OR EXPLOSIVE MATERIALS AND VAPORS WARNING TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE a Never leave surface units unattended at high settings Boilovers cause smoking and greasy spillovers that may ignite Heat oils slowly on low or medium settings b Alway
10. ng the elements apart by placing the assembly template for example over the edge of the bottom chimney paneling to protect it Insert the activated charcoal filters Insert the grease filters 9000032538 en 06 05 EB T E GAGGENAU GAGGENAU HAUSGERATE GMBH CARL WERY STR 34 81739 MUNCHEN GERMANY 089 45 90 03 FAX 089 45 90 23 47 GAGGENAU 780 DEDHAM STREET CANTON MA 02021 USA 800 828 9165 www gaggenau usa com
11. off Fig 3 1 Ventilation duct 2 Control panel 3 Grease filters 4 Lighting Installation accessories for exhaust air mode Stainless steel design ventilation duct LK 010 012 for ceiling heights of 7 4 8 6 LK 010 022 for ceiling heights of 8 6 9 9 Aluminium design ventilation duct LK 011 012 for ceiling heights of 7 4 8767 LK 011 022 for ceiling heights of 8 6 9 9 Installation accessories for circulating air mode Stainless steel design ventilation duct LK 010 112 for ceiling heights of 7 7 8 6 LK 010 122 for ceiling heights of 8 6 9 9 Aluminium design ventilation duct LK 011 112 for ceiling heights of 7 7 8 6 LK 011 122 for ceiling heights of 8 6 9 9 3 Operation Fig 5 GDM or After they have been pressed all functions selection keys except 0 Motor off are backlit in green Light The lighting can be switched on or off regardless of whether the wall extractor is in operation by pressing the key see Fig 4 When you briefly press the key the lighting is increased up to the maximum level You can dim the lighting to the required level by keeping the key pressed Fan levels Three fan speeds and one intensive speed are available see Fig 5 You set the fan level required for each respective cooking situation by pressing the function selector keys 1 2 3 or Int 2 G amp
12. ow as 30 and as high as 36 above the cooktop Using the drilling template drill the 6 holes for the hood area I of the drilling template and the two holes for suspending the chimney area II of the drilling template In the top two securing holes for the hood fix the two hooks d with the countersunk screws c Make sure that the hooks lie flatly on the wall In certain circumstances you may have to countersink the drill holes Fit the included dowels a in the other drill holes Note at least one screw must be installed through a stud Note pay attention to any special accessories that you may have to fit Screw on the retaining bracket for the chimney paneling Detach the grease filters Hang the hood on the two hooks Adjust the suspended element with the recessed head screw and align the hood using a spirit level Fig 20 a Secure the hood on the wall with the four screws b z Fig 21 and 22 For exhaust air mode proceed as follows Establish the pipe connection a Establish the electrical connection Stainless steel chimney only LK 010 012 022 pull the protective film off the chimney s trims Note avoid damaging the sensitive metal surfaces 00000880 Fit the top chimney duct unit into the base Make sure that the fastening holes on the side are at the top Fig 21 Put both chimney duct units onto the hood Pull the top chimney duct unit
13. ownwardly Activated charcoal filters KF 001 010 are available through your specialist dealer Only use original filters Activated charcoal filters do not contain any dangerous substances They can be disposed of through the household refuse collection 11 5 Maintenance Fig 16 Fig 17 12 The appliance must be disconnected from the power supply during all repair work If the appliance does not function correctly check the fuses first If the power supply is functioning correctly but your appliance still does not work please contact your Gaggenau dealer who will provide you with the address and telephone number of your nearest manufacturer s authorized service agent or contact Gaggenau USA on 800 828 9165 Specify the appliance type see rating plate Repairs may only be carried out by authorised technicians in order to guarantee the safety of the appliance Unauthorised tampering with the appliance will invalidate any warranty claims Only ever use original spare parts Lamp replacement Caution disconnect the power supply before replacing lamps switch off the fuse Caution lamps may still be hot shortly after use Risk of burns Detach the ring from the lamp cover Note make sure that the glass will not fall out Fig 16 Pull out the lamp Fig 17 Defective lamps must only be replaced by lamps of the same type 12 V 20 W G4 lampholder Inserting the lamp
14. rating the appliance for the first time please pay attention to the following notes The appliance must be installed and connected by a specialist before it is operated for the first time Conscientiously read through the operating and assembly instructions before operating the appliance for the first time Remove the packaging from the appliance and dispose of it properly Pay attention to the fact that there are accessories in the packaging Keep packaging elements out of the reach of children Thoroughly clean the appliance before using it for the first time see chapter Cleaning and care Before operating the appliance for the first time check that the mains connection is in proper working order 1 3 About use The appliance is intended solely for use in the household and must not be put to any other uses In the event of malfunctions first of all check the household fuses If the problem has nothing to do with the power supply please contact your specialist dealer or your local Gaggenau after sales service When children become old enough to operate the appliance it is the legal responsibility of the parents or legal guardians to ensure that they are instructed in safe practices by qualified persons 2 Features Fig 2 al Grease filter saturation display Lighting Delayed shut off Extraction level intensive Extraction level 3 Extraction level 2 Extraction level 1 Motor
15. rted vertically to allow food or rinsing residues to drain off If possible the inner parts of the housing should be wiped out in hot rinsing water when replacing the filters Caution when cleaning the inside of the housing beware of protruding parts After having cleaned them re insert the grease filters in the wall extractor in reverse order Important the handles of both grease filters must be visible after assembly Press the F key to set the elapsed hours counter to zero Flashing of the indicating lamp goes off Fig 15 Cleaning the extractor hood Clean the exterior of your extractor hood with a soft cloth and mild detergent solution Do not use any strong caustic or abrasive cleaning agents Do not use any abrasive sponges or brushes either Clean the stainless steel extractor hood AW 200 with stainless steel cleaner Do not place any objects with sharp edged or rough bottoms e g ceramic cups on the hood Circulating air mode The activated charcoal filter eliminates kitchen smells in the circulating air mode In normal use 1 to 2 hours daily the activated charcoal filter must be replaced approximately once a year If no activated charcoal filter is installed kitchen smells will not be eliminated Replacing the activated charcoal filter remove the stainless steel grease filters Push in the clips on the side of the activated charcoal filter and remove the activated charcoal filter d
16. s turn hood ON when cooking at high heat or when cooking flaming foods c Clean ventilating fans frequently Grease should not be allowed to accumulate on fan or filter d Use proper pan size Always use cookware appropriate for the size of the surface element WARNING TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE OBSERVE THE FOLLOWING a SMOTHER FLAMES with a close fitting lid cookie sheet or metal tray then turn off the burner BE CAREFUL TO PREVENT BURNS If the flames do not go out immediately EVACUATE AND CALL THE FIRE DEPARTMENT b NEVER PICK UP A FLAMING PAN You may be burned c DO NOT USE WATER including wet dishcloth or towels a violent steam explosion will result d Use an extinguisher ONLY if 1 You know you have Class ABC extinguisher and you already know how to operate it 2 The fire is small and contained in the area where it started 3 The fire department is being called 4 You can fight the fire with your back to an exit 1 Important notes 1 1 For your safety Damaged appliances must not be operated The appliance must only be connected by an authorised specialist paying attention to the relevant regulations of the power supply companies and the regional construction regulations Also observe the assembly instructions Connecting cables must not come into contact with hot cooking surfaces Do not operate the extractor hood witho
17. the appliance must be switched off at fuse point Repairs must be carried out by authorised specialists thus ensuring electrical safety No warranty claims can be lodged in the event of damage caused by failure to observe these instructions Adequate incoming air must be ensured if a wood coal gas or oil heater or an open hearth is operated in the same room as the one in which the hood is installed Safe operation is possible whenever the partial vacuum in the place where the firing equipment is installed does not exceed 4 Pa 0 04 mbar This can be achieved whenever the air needed for combustion is able to enter through openings that cannot be sealed for example in doors windows incoming exhaust air wall boxes or other technical means If the appliance is to be operated only with the window open to ensure adequate incoming air you can use the window switch A switch normally open is fitted on the window On the appliance this switch is connected to the window switch terminal on the main electronics The appliance can now only be operated when the window is open Important the window switch must only be connected by an authorised specialist Note the light function works without restriction After a power failure the extactor will not go on again automatically You can recommence operation by turning a knob or by pressing any key Technical modifications reserved 1 2 Operating for the first time Before ope
18. up into its final position and secure it with 2 screws on the ceiling holder Fig 23 Note avoid scratches when pulling the elements apart by placing the assembly template for example over the edge of the bottom chimney paneling to protect it Fig 22 Insert the grease filters Soecesso Fig 23 17 Fig 25 18 00000880 0000880 For circulating air mode use the installation set included with the ventilation ducts LK 010 112 122 und LK 011 112 122 You also need an activated charcoal filter KF 001 010 Proceed as follows Slightly loosen the screws of the retaining bracket for the chimney paneling Hang the angle pieces onto the screws and tighten the screws Screw the circulating air switch module to the angle pieces 4 screws Shorten the flexible air pipe accordingly Fix the flexible air pipe with hose clamps Fig 24 Establish the electrical connection Stainless steel chimney only LK 010 112 122 pull the protective film off the chimney s trims Note avoid damaging the sensitive metal surfaces Fit the top chimney duct unit into the base Make sure that the fastening holes on the side are at the top Put both chimney duct units onto the hood Pull the top chimney duct unit up into its final position and secure it with 2 screws on the ceiling holder Fig 25 Note avoid scratches when pulli
19. ut inserted lamps Never operate the appliance without a grease filter Hazardous or explosive substances and vapours must not be extracted The user is responsible for expert use and the perfect condition of the appliance Only ever operate the appliance under super vision Caution Over greased filters are a fire risk Only ever deep fry under the extractor under constant supervision Be sure to clean the grease filter on a regular basis and change the activated charcoal filter Fire risk Do not flamb meals under the extractor hood Operation of the extractor hood above a hearth for solid fuels which poses a fire risk e g sparks is only permitted if the hearth possesses a closed and fixed lid The current local regulations must be obeyed This does not apply to gas hobs and gas cookers Hobs may only be used under the extractor hood when pots and pans are placed on them When using more than 3 gas operated rings at the same time please operate the extractor hood at level 2 or higher This prevents a build up of heat in the appliance For safety reasons do not place any heavy objects on the top of the appliance Do not clean the appliance with a steam cleaning apparatus or with water pressure because this poses a risk of short circuits Isolate the appliance from the mains during every maintenance operation To do this remove the mains plug or actuate the corresponding fuse If the mains plug is not accessible
Download Pdf Manuals
Related Search