Fujitsu ST4000 User's Manual
Contents
1. 2 Gently pull the tray out until a media disc can easily be placed in the tray Wy CAUTION There may be a protective sheet in the tray from when it was shipped please make sure it is removed before operating the drive 3 Place the media into the tray label side up with the hole in the center of the disc Snap the disc onto the raised circle in the center of the tray 4 Gently push the holder tray back in until you hear a click REMOVING MEDIA Refer to Figure 8 for the following steps 1 Push and release the eject button on the front of the media player drive This will stop the drive and the holder tray will come out of the system a short distance 2 Gently pull the tray out until the disc can easily be removed from the tray 3 Carefully remove the media disc from the holder tray 4 Gently push the holder tray back in until youhear a click Tablet Dock User s Guide Figure 8 Loading Ejecting Media rue Stylistic ST4000 Series Tablet Dock SAFETY PRECAUTIONS Never move the Tablet Dock with the system docked unless it is fully locked If the system were to undock accidentally it could drop and be damaged Never power off or remove the computer from the Tablet PC while the system is reading or writing to a floppy or hard drive This could result in data loss Always wait at least 5 seconds before restarting the Tablet PC after turning it off Failure to do this can result2. FUJITSU Fujitsu Stylistic ST4000 Series TABLET Dock User s GUIDE ru Stylistic ST4000 Series Tablet Dock Fujitsu and the Fujitsu logo are registered trademarks of Fujitsu Ltd and Stylistic is a registered trademark of Fujitsu Ltd Microsoft and Windows are registered trademarks of the Microsoft Corporation All other trademarks mentioned herein are the property of their respective owners Product description data reflects Fujitsu design objectives and is provided for comparative purposes actual results may vary based on a variety of factors Specifications are subject to change without notice 2003 Fujitsu All rights reserved Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation Tablet Dock User s Guide Fujitsu Stylistic ST4000 Series Tablet Dock This guide contains information on using your Tablet Dock You should read this section before using the dock even if you are familiar with other computer docking devices Your Tablet Dock may be configured in one of two ways Configuration Tablet Dock with CD ROM Drive Tablet Dock with Combo DVD CD RW Drive Your Fujitsu Stylistic ST4000 Series Tablet Dock has the following interfaces Port Jack Purpose LAN RJ45 Allows you to connect a Local Jack Area Network LAN devic
3. of the Tablet Dock Figure 2 Always check the icon by the port before inserting Tightenscrews if available 2 You may switch between the internal monitor and external monitor using the Display Configuration utility located in the system tray at the bottom right of the screen or through the Control Panel settings To Attach a USB device Use of the USB ports allows attaching USB devices to a docked system 1 Securely insert the connector into one of the three USB ports on the left side of the Tablet Dock Figure 2 It may be necessary to wait a short time while the appropriate drivers are located and installed by the system To Attach an IEEE 1394 device The IEEE 1394 jack allows attaching peripherals such as digital cameras to a docked system 1 Securely insert the connector into the IEEE 1394 jack on the left side of the Tablet Dock Figure 2 Refer to the device manufacturer s installation and usage instructions for configuration instructions Tablet Dock User s Guide To Attach External Audio Equipment The Tablet Dock provides a Line Out jack for head phones or external speakers Point Connecting external speakers including headphones or microphone disables the system s internal speaker or internal microphone 1 To attach an external audio device insert the plug into the Line Out jack on the back of the Tablet Dock Figure 2 To Attach a LAN Device The LAN 45 jack all
4. Never connect the Tablet Dock to AC power by using an extension cord For additional environmental specifica tions see Tablet Dock Specifications on page 10 Point Always use your Tablet Dock on a solid flat level clean and dry surface Nearby there should be electric power as well as a telephone jack for a modem or a LAN port Save packing material in order to safely ship or store the Tablet Dock in the future roe Stylistic ST4000 Series Tablet Dock IDENTIFYING THE COMPONENTS Before using your Tablet Dock you should familiarize yourself with its various features Positioning Guide Side Latch Back Latch both sides Interface Connector Lock Release Button Back Latch Lock Handle Positioning Guide Platform Kensington Lock Slot Front of base Do not use as a carrying handle CD ROM or Combo DVD CD RW Drive Easel Release Buttons IEEE 1394 Jack LAN 45 Jack External Monitor VGA Port Line Out Jack USB Ports Qty 3 DC In Jack Figure 2 Back View DOCKING YOUR SYSTEM Microsoft Windows uses plug and play technology to automatically load the files necessary to operate your Tablet Dock and any attached devices Point Microsoft Windows uses plug and play technology to automatically load the files necessary to operate your Tablet Dock and any attached devices 1 Plug the syste
5. d applications Point Prolonged use of the media drive such as watching a DVD movie will substantially reduce your battery life if no other power source is attached Be sure to attach an AC Adapter when using the Tablet Dock for prolonged tasks All Fujitsu DVD players are set to play DVD titles with region code number 3 which is specified for the Asia Pacific market The region number is a regional restriction code defined by the DVD Forum consortium Different region codes are recorded on video DVD titles for publication in different areas of the world If the regional code of the DVD player does not match the regional codes on the titles then playback is impossible You can change the region code on the DVD player using the Properties menu of the DVD software Note however that you can only change the region code up to four times After the fourth change the last region code entered becomes permanent and cannot be changed Wy CAUTION Do not operate your media drive unless your system is sitting on a relatively flat surface Using the drive when the system is not level may damage the drive or prevent proper operation LOADING MEDIA Refer to Figure 8 for the following steps To load a disc into your media player drive follow these steps 1 Push and release the eject button on the front of the drive to open the holder tray The tray will come out of the system a short distance
6. e or broadband device such as a cable modem VGA Port Allows you to connect an external monitor Line Out Allows you to connect Jack headphones or external speakers DC In Allows you to connect power to the system USB Ports Allow you to connect up to three Quantity 3 Universal Serial Bus USB Revision 1 1 devices or hubs IEEE 1394 Allows you to connect a Jack peripheral such as a digital video camera A WARNING Do not expose the Tablet Dock to rain moisture excessive dirt or temperatures outside the Environmental Specifications as it may cause fire and shock hazards High voltage is present inside the Tablet Dock Do not remove the cover under any circumstances There is a serious shock hazard Switch the unit OFF unplug the power cord and contact a qualified service tech nician or Fujitsu Services and Support if Liquid has been spilled on the Tablet Dock Tablet Dock has been dropped e Small objects went inside your Tablet Dock which may cause a short circuit and or create a hazard of shock e Fuses continue to blow out Adistinct change in the operation and performance of the Tablet Dock occurs The power cord or plug is damaged or frayed The unit should be operated only from the type of power indicated on the marked label The socket outlet must be installed near the equipment to be accessible using the system s AC power cord
7. in damage to the system s electrical circuitry TABLET DOCK SPECIFICATIONS Feature Details Dimensions Environmental 100 pin docking connector e VGA D sub 15 pin female connector DDC compliant Line Out Jack 3 5mm for head phones or external speakers DC input 16VDC IEEE 1394 4 pin standard connector USB Universal Serial Bus Ports quantity 3 LAN connector 100Base TX 10Base T 45 System Bay Accommodates CD ROM or DVD CD RW drive 16VDC with current of 3 75 Height 12 95 329mm Width 8 66 220mm Depth 10 35 263mm 5 95 Ibs 2 7Kg Operating Temperature 40 95 F 5 35 Storage Temperature 5 140 F 20 60 C Relative Humidity 20 80 Table 1 Tablet Dock Specifications 10
8. m s AC adapter into a wall outlet then into the Tablet Dock s DC Input jack 2 Set the ST4000 series system on the Tablet Dock with the system oriented in the same direction as the dock See Figure 3 for location The connector in the back of the system should be aligned with the interface connector on the Tablet Dock Figure 3 Docking the system 3 Carefully push the system towards the docking port until you hear a click The click indicates that the side latches are in place Note that the system is not yet locked into place until the following step is performed 4 Firmly pull the lock handle down as far as it will go This engages the back latches and side latches and locks the system in place 5 Your Tablet Dock is now ready for use You may now attach devices to it Tablet Dock User s Guide Point The front portion of the base should not be used as a handle It is designed to support the system when it is installed in the Tablet Dock but not as a handle UNDOCKING YOUR SYSTEM Use these instructions when you want to remove your system from the Tablet Dock Point The system can be removed from the Tablet Dock whether the system is operating or not 1 Press the lock release button on the top of the right slide above the lock handle While holding it down pull the lock handle upwards to unlatch the back latches from the system 2 Pull the system upwards away from the
9. ows you to connect the system s internal Fast Ethernet to a LAN or broadband devices such as a cable modem DSL or satellite internet 1 To attach a LAN device insert the plug into the LAN 45 jack on the back of the Tablet Dock Refer to the device manufacturer s installation and usage instructions for configuration instructions USING THE INTERNAL MEDIA DRIVE The Tablet Dock is outfitted with either a CD ROM drive or a Combo DVD CD RW drive depending upon the configuration of your dock A CD ROM drive allows you to access software data or audio CDs DVD CD RW combo drive allows you to access movies audio software data or audio DVD CDs and to write data onto recordable CDs Stylistic 574000 Series Tablet Dock CD ROM drive All of the software you need to run the CD ROM drive is already installed on the ST4000 series system The drive will work as soon as the system is docked and powered up Combo DVD CD RW drive Packaged with the Tablet Dock is a CD that contains the applications required to run the DVD and CD RW features The combo drive will only act as a CD ROM drive until you install the additional software To install the additional software refer to the instructions on the CD The instructions for installing and removing disks is the same for both drives For information about the software s features and capabilities refer to the help files associated with the relate
10. platform The system is now undocked ru Stylistic ST4000 Series Tablet Dock CHANGING SYSTEM ORIENTATION Microsoft Windows uses plug and play technology to automatically load the files necessary to operate your Tablet Dock and any attached devices Figure 5 Landscape Orientation To change the position of the display simply grasp the edge of the system and turn it in the direction shown in Figures 6 and 7 e Ifthe display is in portrait position turn the display to the right as shown in Figure 6 e If the display is in landscape position turn the display to the left as shown in Figure 7 Figure 6 Changing Display from Portrait to Landscape Mode Figure 7 Changing Display from Landscape to Portrait Mode Point When you change the orientation of the system the display does not change orientation To change the orientation of the display use the Orientation application button See your system User s Guide for more information CONNECTING DEVICES Once your system is installed in the Tablet Dock you are ready to attach external devices to the dock To Attach an External VGA Monitor This option allows you to use an external monitor with your system The only requirement is that the external device monitor projector is a VGA device Consult the instructions that come with the device 1 Securely insert the external monitor plug into the display port on the back
Download Pdf Manuals
Related Search