Fujitsu 280X1024@75Hz User's Manual
Contents
1. 1 Power Switch Digital control light touch switch used for turning on or off monitor power 2 Power Indicator When the monitor is under normal working condition the indicator will light green or blue if the monitor is under saving mode the indicator will light red or off And the indicator will turn off under the power off mode When the power indicator turns off it means that the monitor is under off mode but please pay attention that the adaptor is still in charge so please disconnect the adaptor when the monitor is not used for the purpose of safety Copyright Fujitsu Australia Ltd and its licensors 2007 page 7 OPERATION 3 Menu Button Activate OSD enter sub menu select items and confirm selection 4 AUTO Button Automatically set the screen display to optimum 5 gt Button Select and adjust the OSD items Increase the value 6 Button Select and adjust the OSD items Decrease the value 7 VOL Select VOL Volume Decrease Decrease the value 8 VOL Select VOL Volume Increase Increase the value Copyright Fujitsu Australia Ltd and its licensors 2007 page 8 OPERATION 3 2 OSD menu and operation menu introduction Press the MENU to call out the OSD menu main menu please see the illustration as below With gt or lt to select the desired items and then press the MENU button for adjustment with gt lt button to adjust the display items2. IMPORTANT PRECAUTIONS A WARNINGS 1 Before using this device please read all the instructions in this manual carefully 2 Please keep the manual carefully for future reference 3 Unplug this device from the wall outlet before cleaning Do not use liquid cleaners or aerosol cleaners Use a damp or wet cloth to clean Please use LCD screen detergent for cleaning if it is still dirty 4 Do not use the parts not recommended by the manufacturer otherwise it may cause a hazard 5 When unplugging the power cord of the monitor or adapter please hold the plug with your hand do not pull the cord directly 6 Do not place any object on the power cord Do not trample it either 7 Do not use the device near water sources e g bathtub basin kitchen sink or washing machine Do not place the device on a wet floor or near a swimming pool etc Do not touch the screen with your fingers or other hard objects 8 Slots and openings on the housing and its back or bottom are provided for ventilation To ensure reliable operation of the components and to protect them from overheating these openings must not be blocked or covered placing the device on a bed sofa rug or other similar surface The device should never be placed near or over a radiator or heater and should not be placed in a built in installation unless proper ventilation is provided 9 Make sure that the device is at least 5cm distance from the wall or other objects around when it
3. Volume use por lt to adjust the volume to optimum option Mute use or lt to select Mute Sound Return back to previous menu MENU Select Copyright Fujitsu Australia Ltd and its licensors 2007 page 10 OPERATION System setting menu Language use or lt to select desired language Menu display time use or lt to select the desired time for menu display Saving time use or lt to select desired time for display so as to meet your requirement Reset reset all the set value to factory setting Return back to previous menu Yo ES BS SL aty Return Language English OSD Timeout 60 Power Save 8 Reset AS OFF eee N 1 USER 1280X1024 75Hz Display mode when setting OFF it is display mode whensettingON it will be 4 3 display mode Exit and signal resource selection menu Select terminal input select input terminal for signal input option Exit exit OSD menu fay A a aw Exit of VGA 1 DVI AAi USER 1280X1024 75Hz Note Hot Key of volume brightness contrast Without OSD mode your may press 4 button to call volume adjustment directly when the volume menu is not exit please press MENU to call brightness and contrast adjustment you may use gt lt to adjust it to optimum Copyright Fujitsu Australia Ltd and Its licensors 2007 page 11 OPERATION 3 3 Safeguard When the video signal of your computer exceeds the frequ
4. display on the wall 1 3 Packing list Please make sure the following items are included with your LCD display before installation ALCD monitor with pedestal AVGA signal cable DVI D signal cable option An audio cable option A power cord A AC adapter User s manual qualification and warranty cards If any of there items are missing please contact with your dealer for technical support and customer service NOTE be sure to save original box and all packing material for transport in future if the display need Copyright Fujitsu Australia Ltd and its licensors 2007 page 4 INSTALLATION INSTALLATION 2 Installation 2 4 Power on E E Turn on the monitor and computer and then indicator will light green or blue when the screen is under normal condition Please check to see if there is any wrong with the connection of video signal cable if the indicator lights red 2 5 Self inspection If the monitor inspects there is no horizontal and vertical signal it will prompt to check the video input please refer to the illustration below and the monitor will enter into power saving mode after several Installation hole for wall hanging seconds the indicator will light red The En NO SIGNAL VGA signal input jack screen will restore to normal display once Dees receiving video signal 2 6 Image Adjustment Please adjust the image according to your need please re
5. licensors 2007 page 12 OPERATION 20 1280x1024 63 980 60 000 21 1280x1024 79 976 75 025 22 1440x900 55 935 60 000 23 1440x900 70 635 75 000 24 1680x1050 65 290 60 000 25 1600x1200 75 000 60 000 26 1920x1200 74 038 60 000 Note 22 LCD Monitor is applied to items 1 25 recommended mode 3 5 Power management system This monitor complies with EPA Energy Star and is compatible with VESA DPMS standard the saving mode is shown as below Mode Power Indicator Power Consumption 22 Normal Green or blue lt 50W Standby Saving Red or turn off lt 5W Power Off Turn off lt 3W Copyright Fujitsu Australia Ltd and its licensors 2007 page 13 TECHNICAL SPECIFICATION 4 1 22 TFT LCD monitor specification 22 Screen model 22 Active Matrix TFT LCD Dot pitch H x V 0 27675x0 27675mm Surface treatment Anti glare 3H Active display area H x V 464 94mm H x290 5875mm V Max Resolution 1680x1050 Contrast 1000 1 Typ Brightness 300cd m Typ Responsive time 5ms Typ Display color 16 7M 6bits Hi FRC Visible angle left right 70 70 or 80 80 up down 75 75 or 85 85 Input signal video signal synchronization RGB simulation 0 7V p p TTL positive or negative polarity Display format VGA SVGA XGA WSXGA Audio input terminal RCA terminal x2 option Signal connec
6. to optimum press again for confirmation and exit adjustment kJ Brightness use or lt to adjust the brightness to optimum Contrast use gt or lt to adjust the contrast to optimum Return back to previous menu Oe amp KF MENU Select Image adjustment menu Auto adjust with this button to adjust the display to optimum H position adjustment use or lt to adjust the horizontal position to optimum V position adjustment use or lt to adjust the vertical position to optimum Image position level clock set use or to adjust the image position level to optimum Phase adjustment use or lt to adjust the focus and definition to optimum Return back to previous menu 22a MENU Select Copyright Fujitsu Australia Ltd and Its licensors 2007 page 9 OPERATION EN Color adjustment menu Red Green Blue color adjustment use gt or lt to adjust the value of red green and blue to change the image color so as to meet your needs Color temperature use or lt to select desired color temperature 9300k 6500k USER Color adjustment it can be adjusted if under shadow mode If you are not satisfied with the color temperature set by manufacturer you may set the color temperature to USER mode it will light red at this time When enter adjust menu please use or lt to adjust R G B to change the color of image Return back to previous menu MENU Select Audio adjustment menu
7. User s Manual FUJITSU 22 inch Color LCD MONITOR Before operating the monitor please read th s manua thorough y and reta n tfor future reference Itw he piydu to operate youtlm dnitor easily All rights reserved Copyright Fujitsu Australia Ltd and Ita lloensors 2007 Table of Contents EMC COMPLIANCE 1 IMPORTANT PRECAUTIONS 2 1 Introduction 1 1 G6nelale snaar ers ee ee eR ee rn ean 4 1 2 Features ss 5 aan anaa ASRS RR aS S RS SES 4 1 3 Packing List Atr As 528229 S eRe SPSS eae See aoa 4 2 Installation 2 1 Connection of signal cable 7 7 r rrr rrr rrr rrr c rte 5 2 2 Connection of power cord 7 7 7 7 5 2 3 Connection of Audio cable 757 5575555555 5 24 Poweron 228s ons Sr eS eee a aS a a 6 2 5 Self inspection 6 2 6 Image Adjustment 7 rr rrr rrr rrr r ctr r rrr rrr 6 3 Operation 3 1 OSD DUI anasa A asin esas 7 3 2 OSD menu and operation menu introduction 9 3 3 Safegliand Sates oe Sra See ee eae 12 3 4 Power management system 7 7 7 7 7 7 7 7 77 7 7 7 12 3 5 Setting of display mode 7 57 5 r rrr rrr rrr rrr re 13 4 Technical specification 4 1 22 TFT LCD monitor specification 7 7 7 7 14 4 2 Pin assignment of signal c
8. able 15 4 1 Visual Inspection ss lt s2ss s2 sSoess aeaee sess es 15 5 Trouble Shooting 16 Copyright Fujitsu Australia Ltd and its licensors 2007 EMC COMPLIANCE EMC COMPLIANCE This device has been tested and found to comply with the standards for a class B digital device pursuant to Part 15 of FCC Rules Those standards are designed to provide reasonable protection against harmful interference in a residential installation This device generates and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications If this device does cause harmful interference to radio or television reception which can be determined by turning the device off and on user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the device and receiver Plug the device into a wall outlet different from that connected to the receiver Consult the dealer or an experienced radio TV technician for help CAUTION any change or modification not expressly illustrated in this manual may void the warranty NOTE any unshielded cable is not allowed to be used in the device Copyright Fujitsu Australia Ltd and its licensors 2007 page 1 IMPORTANT PRECAUTIONS
9. ctly 18 The power cord is the main facility to turn on off the device unplug it if the device is not used for a long period of time 19 Store the device at a place of good ventilation avoid strong sunlight high temperature or humidity 20 Store the device at a place at 20 C 55 C room temperature Otherwise it may cause permanent damage Copyright Fujitsu Australia Ltd and its licensors 2007 page 3 INTRODUCTION 1 Introduction 1 1 General Thank you for purchasing the latest model of LCD monitor with advantages of high display performance and light weight etc meanwhile with the power saving and no radiation features the latest LCD will bring you comfortable safe and environmental protection brand new visual experience Your purchase and use of this product is highly appreciated 1 2 Features High performance intelligent multi frequency scanning use active matrix Thin film transistor liquid crystal display TFT Micro Computer digital technology control no radiation no glare built in multimedia speaker system option Built in AV signal connection terminal and 8 terminal option Comply with VESA DPMS International Power Saving Regulation Support DDC 1 2B and Windows PNP Plug amp Play Microprocessor based with OSD On Screen Display control be able to adjust the image to optimum Built in hoisting hole complying with International Standard VESA which is able to hang the
10. ency range of monitor refer to product specification the micro computer of monitor will turn off the sync signal of horizontal and vertical for the purpose of monitor protection please refer to the illustration below The monitor will enter saving mode after few seconds and the power indicator will light red Please set the output frequency of your computer 1 OUT OF RANGE within the acceptable range of monitor so that the monitor can work normally 3 4 Setting of display mode With standard VESA and DDC function the monitor will scan frequency output power performance etc and transfer to PC after turning on when you use the video card with VESA DDC1 2B function And it will identify the connection mode of display and select the proper resolution The preset mode before leaving factory is as below Mode Resolution Horizontal KHz Vertical Hz 1 640x400 31 469 70 087 2 640x480 31 469 59 940 3 640x480 37 861 72 809 4 640x480 37 500 75 000 5 720x400 31 469 70 087 6 800x600 35 156 56 250 7 800x600 37 879 60 317 8 800x600 48 077 72 188 9 800x600 46 875 75 000 10 1024x768 48 363 60 004 11 1024x768 56 476 70 069 12 1024x768 58 038 71 918 13 1024x768 60 023 75 029 14 1024x768 48 019 60 000 15 1024x768 47 700 60 000 16 1152x864 67 500 75 000 17 1280x800 49 702 74 900 18 1280x800 62 795 60 000 19 1280x960 60 000 60 000 Copyright Fujitsu Australia Ltd and its
11. fer to the Operation in Section Three Audio input jack VGA signal input connect to computer VGA signal output jack DVI signal input connect to computer DVI signal output jack 3 Power jack connect to adaptor DC output jack 4 Audio input connect to computer sound card audio output jack 2 1 Connection of signal cable Before connecting your monitor and PC with signal cable please turn off your monitor and computer And then insert one end of the signal cable into the VGA or DVI jack on your computer and lock it with two fixed screw for ensured grounding Finally please insert another end of signal cable to the VGA or DVI signal input jack of monitor and lock it with fixed screw 2 2 Connection of power cord First insert one end of power cord into the input jack of adaptor and another end into power outlet then insert the output terminal of adaptor into the power input jack of monitor 2 3 Connection of Audio cable Please insert one end of audio cable into the sound card audio output terminal on your computer another end into the audio input terminal of monitor Copyright Fujitsu Australia Ltd and its licensors 2007 Copyright Fujitsu Australia Ltd and its licensors 2007 page 5 page 6 OPERATION 3 Operation 3 1 OSD button AUTO MENU gt 4 3 6 5 1 2 AUTO MENU lt gt I 4 3 2 1 6 5
12. gnal cable if there is any curved or broken pin please replace it Enter the OSD color adjustment menu to set the display color to the optimum Copyright Fujitsu Australia Ltd and its licensors 2007 page 16
13. is in use 10 The power supply must respond to that stated on the rating plate If you have any query about the power supply please refer to the dealer or local power supply provider 11 As a safeguard measure the monitor or adapter is equipped with a power cord with three terminal plug the third terminal is grounded If the plug cannot be inserted into the outlet please contact an electrical technician for replacing the original outlet while keeping the safeguard measure in effect 12 Ensure that the power socket and cord in use are able to take the sum of the rated currency of all the products 13 Do not put the device at the place where user is subject to mal operation Copyright Fujitsu Australia Ltd and its licensors 2007 page 2 IMPORTANT PRECAUTIONS 14 Observe all the warnings and instructions described in the manual 15 Do not overload the power outlet or use any extension cord otherwise it may cause fire or electric shock 16 Do not attempt to repair this device yourself since opening or removing covers may expose you to dangerous voltage or other hazards Refer servicing to qualified service personnel 17 Unplug this monitor or AC adaptor from the wall outlet and refer servicing to qualified service personnel under the following conditions a When the power cord or plug is damaged or worn b If the device has been dropped or its housing has been damaged c When the performance of the device deteriorates distin
14. k normally please refer to the follow methods for common problems quickly if you need assistance please call the dealer where you purchased the Monitor A There is no Screen Image LED no light Please check to see whether the power cord is securely connect to the monitor and wall outlet and whether the display is in power saving mode B There is no Screen Image LED light red Please to see whether the display card of PC is loosed and check the connection between signal cables and display C The display is not clear or the image is too large or too small Enter the OSD image adjustment menu and then select Auto Adjust to make the display to adjust automatically to optimum D The image is too light or too dark Enter the OSD brightness adjustment menu and then select the gt lt to adjust the brightness and contrast to optimum E The screen is overheated Please keep at least 5cm around the display for ventilation and do not place anything onto the monitor F Dark display after power on facula This is normal Due to the temperature difference the backlight will not give out light equably at the beginning of powering on but the backlight lamp will come to normal work after 20 minutes the darkness and facula will disappear at this time G The image is distorted to flash and shake Check the set of computer and choose the proper resolution then readjust and renovate the resolution H The color is abnormal Check the connection of si
15. tor 15 pin D sub or DVI D Option Panel button Power switch LED indicator OSD menu button auto setting OSD Function Contrast brightness auto adjustment image level phase image h position image v position OSD h position OSD v position color temperature RGB language Adaptor AC input 100V 240V 50 60Hz Adaptor DC output 12V 5A Max Power consumption 50W Working environment Temperature 0 cC C Humidity 20 80 Storage environment Temperature 20 C C Humidity 20 80 Packing dimension LxWxH 585X200X502mm Weight Kg N W 5 5 G W 7 5 Note all technical specifications in this manual and on the packing are subject to change without prior notice page 14 Copyright Fujitsu Australia Ltd and its licensors 2007 TECHNICAL SPECIFICATION 4 2 Pin assignment of signal cable Pin Signal D sub Pin Signal D sub 1 Red 9 DDC Power 2 Green 10 Ground 3 Blue 11 Ground 4 Ground 12 SDA FOR DDC 5 Test Cont 13 H sync 6 Red Ground 14 V Sync 7 Green Ground 15 SCL FOR DDC 8 Blue Ground 4 3 Visual Inspection Even the normal pixels on the LCD screen reach 99 99 or higher there may be 0 01 or less pixels showing dark or light while displaying page 15 Copyright Fujitsu Australia Ltd and ita licensors 2007 TROUBLESHOOTING 5 Troubleshooting If your monitor cannot wor
Download Pdf Manuals
Related Search