Fujitsu Siemens Computers Rugged Tablet Case User's Manual
Contents
1. and hold it by the edge opposite the battery Battery Rigid edge Figure 4 Inserting the system in the case Insert the battery edge of the system into the wide rigid edge of the case the side with the D rings Push it in until it is flush with the edge of the case Figure 4 Lift the flexible edge of the case sufficiently to allow the system to lie in the case then release the flexible edge Overlap the two halves of the hand strap so that they attach to each other Flexible edge Figure 5 Enclosing the system Figure 6 System in case Using the hand strap When you want to hold the case using the elastic hand strap first separate the two halves Place your hand in a comfort able position on the bottom of the system and re secure the strap against the back of your hand When not using the hand strap attach it snugly against the back of the computer Installing the handle To install the handle perform the following steps 1 Insert one end of the handle into the D ring with the buckle facing outwards Figure 7 FA D ring Handle strap Figure 7 Inserting handle strap 2 Bend the end of the handle strap towards the buckle and tuck it under the edge of the buckle Figure 8 3 Pull the strap taut then insert the end through the sec ond edge of the buckle Figure 9 4 Pull the end of the strap until it is taut Figure 10 Repeat the procedure above with the other end of2. strap is designed to let you hold your system securely when it is installed in the case Use of the hand strap is highly recommended The hand strap consists of two parts each of which has a Velcro strip on one end and a retaining bar at the other Note that the longer of the two strips with the fuzzy Velcro should be positioned in the top slot while the shorter strip with the hooks Velcro should be inserted in the bottom slot To install the hand strap perform the following proce dure 1 Position the case so that it is face down and the hand strap slots are facing up Figure 2 Insert the shorter of the two pieces of the hand strap into the bottom slots with the Velcro hooks strip fac ing up Figure 3 Pull it through until the retaining bar is snug against the case Retaining bar A Retaining bar Longer Velcro strip fuzzy side facing down L Shorter Velcro strip hooks facing up Figure 3 Inserting hand strap halves Insert the longer piece of the hand strap into the top slot with the fuzzy Velcro strip facing down Figure 3 Pull it through until the retaining bar is snug against the case Installing the system To install your system into the rugged tablet case perform the following steps 1 Position the case face down the same orientation as when you installed the hand strap Position the system in tablet mode with the display fac ing down
3. the handle Figure 8 Inserting strap into buckle Sp Figure 9 Pulling strap through buckle Figure 10 Tightening the strap Installing the shoulder strap To install the shoulder strap open the spring loaded clips on both ends and attach one to each of the D rings Figure 11 Figure 11 Installing the shoulder strap 10 Installing the pen tether To install the pen tether insert one end into one of the D rings then feed it through the loop on the other end Pull it snug against the D ring Feed the loose end of the tether through the hole on the end of the pen slide the loop over the tip of the pen then down the barrel Pull it snugly to tighten the loop Caring for the rugged tablet case The case is made of rugged materials and is designed to withstand daily use Treat the case as you would a briefcase or purse Occasionally the case may become soiled To clean it remove the system from the case if it is installed then use a clean cloth and warm soapy water to wash the soiled area 12 1250 E Arques Avenue M S 122 Sunnyvale California 94085 FU ITSU For more information call 1 877 372 3473 or visit our Web site at us fujitsu com computers For technical support call 1 800 8fujitsu 1 800 838 5487 or e mail us at 8fujitsu us fujitsu com Fujitsu the Fujitsu logo and LifeBook are registered trademarks of Fujitsu Ltd All other trademarks mentioned herein
4. Fujitsu Computer Systems Corporation Rugged Tablet Case User s Guide These instructions provide details on using the rugged tablet case with your Fujitsu LifeBook notebook when it is in tablet mode The case provides added protec tion when transporting using or storing the note book We recommend that you read these instructions prior to using the case with your computer Package Contents Included in the package are the following items Rugged tablet case Full size pen designed to fit in the pen holder on the front of the case This pen will not fit in the pen holder that is built into the system Pen tether Hand strap 2 pieces Case handle Shoulder strap D rings Pen Holder 2 places Built in microphone access Fingerprint sensor access Port slot access System status Application power suspend button access resume button access Figure 1 Rugged tablet case Front The pen which came with the system is too small to fit snugly in the pen slot so a full size pen is included with the case The pen holder on the top front of the case should be used to store the pen When the system is in the case the system pen slot is not accessible Figure 1 Use the pen which came with the case in the pen holder See note above Case handle PC Card access Hand strap slots Wile pE i Figure 2 Rugged tablet case back Installing the hand strap The hand
5. are the property of their respec tive owners Product description data represents Fujitsu design objectives and is provided for comparative purposes actual results may vary based on a variety of factors Specifications are subject to change without notice 2007 Fujitsu Computer Systems Corporation All rights reserved FPC58 1592 02
Download Pdf Manuals
Related Search