Fujitsu Siemens Computers FMW51DS1 User's Manual
Contents
1. Disconnecting the Docking Station To disconnect the docking station from your pen tablet 1 Suspend operation of your PenCentra 130 pen tablet 2 Turn off peripheral devices that are attached to the docking station 3 Push the latch button down to unlatch it from the pen tablet 4 Pull the pen tablet out of the docking station ina straight line Do not rock the components as you pull them apart You can resume system operation of your PenCentra 130 pen tablet PenCentra 130 is a trademark of Fujitsu Personal Systems Inc 1999 Fujitsu Personal Systems Inc 7 99 58 0677 00A2. FMW51DS1 Docking Station User s Guide PenCentra 130 These instructions provide details on using the PenCentra 130 Docking Station with your pen tablet The PenCentra 130 Docking Station is best suited for desktop computing tasks when a quick and temporary connection to peripheral computer equipment is needed and the pen tablet alone does not provide the necessary connectivity The docking station provides the following interfaces for connection to peripheral computer equipment see Figure 1 for locations e Serial port This port allows you to connect an external device with a serial interface Note The docking station serial port does not support the ring indicate feature e Pin 9 on the docking station serial port does not supply 5 volts as the pen tablet does e PS 2 style port This port allows you to attach a PS 2 style mouse or keyboard e USB port This port allows you to attach a Universal Serial Bus USB connector e DC input This port allows you to connect an AC Adapter to provide input power This input can be used for powering the system while it is running or for charging the system battery The following illustration shows the location of peripheral interfaces on the docking station Serial Port PS 2 style Port USB Port DC Input Figure 1 Docking Station Rear oe FUJITSU Caution Circuitry in the PenCentra 130 and the docking station is designed to be robust however
3. ctor screws if used to maintain consistent and reliable connections between the devices and the docking station PenCentra 130 is a trademark of Fujitsu Personal Systems Inc 1999 Fujitsu Personal Systems Inc 7 99 58 0677 00A 5 Install the PenCentra 130 in the docking station To do so press down and hold the latch button on the right side of the docking station see Figure 2 Latch Button Latch Docking Station Pivot Hole Figure 2 Installing the PenCentra 130 Tilt the pen tablet to the left and slip the pivot hole over the pivot point on the left inside of the docking station reference arrow 1 in Figure 2 While holding down the latch button reference arrow 2 in Figure 2 gently press the right side of the pen tablet into the docking station until it is resting on the base reference arrow 3 in Figure 2 Release the latch button and lift the pen tablet to make sure it is latched in properly 6 Turn on the peripheral devices attached to the docking station 7 Resume PenCentra 130 system operation If the required driver software for an attached peripheral device is not installed the device may not work or may work incorrectly Contact your local help desk or refer to the documentation provided with your peripheral device and install the driver software at this time oe FUJITSU You can now use your pen tablet with the peripheral devices attached to the docking station
4. the pen tablet and connected devices can be damaged if procedures given in these instructions are not followed when connecting devices To avoid damage to your hardware observe the following guidelines when using your docking station Do not touch connector pins or connector sockets on your equipment Electrostatic discharge can damage interface circuitry in your equipment Do not connect or disconnect any device when the system is running Always turn off devices and suspend system operation before connecting to or disconnecting peripheral devices Do not use corresponding connectors on the pen tablet and the docking station simultaneously Interfaces on the pen tablet are duplicated by the docking station Connecting devices to equivalent connectors on the pen tablet and docking station at the same time could damage equipment Do not jam or force component connections Installing the PenCentra in the Docking Station To install your PenCentra 130 into the docking station 1 Suspend the pen tablet operation by either pressing the suspend resume button or by shutting down from the Start menu 2 Turn off any peripheral devices you intend to connect to the docking station 3 Turn off any peripheral devices that are already connected to the docking station 4 If you are connecting or disconnecting peripheral devices to the docking station do so now When connecting peripherals tighten the conne
Download Pdf Manuals
Related Search