Frigidaire FRS6B5EEQ2 User's Manual
Contents
1. The two digital displays on the left half of the control panel indicate the current settings or temperatures of your freezer and fresh food compartments The models with a 2 digit temperature display are for reference only and do not display the current accurate compartment temperature Should you desire to see what the current accurate temperature is place a separate thermometer inside the freezer or fresh food compartment in the desired location Freezer Temp Fresh Food Temp Mod Yy Hiro G Temperature Display Features may vary Freezer Door Ajar Fridge On Off Green OK Yellow Order Red Change NOTE Cold Cold Freezer Freezer The advanced electronic control system in your refrigerator includes additional display modes that service professionals can use to rapidly diagnose performance issues Door Ajar Freezer Fresh Food On Off Colder e O 9 is coldest O Press amp Colder hold Allow 24 hrs for adjustments Single Digit Display Features may vary TEMPERATURE CONTROLS Freezer Temp Fresh Food Temp A A Vv of V To adjust the temperature to a higher or lower setting press the Up Cold or Down Colder button closest to the display The first time you press the button the display shows current setting you entered Each press of the button after that changes the setting by one The display shows your new setting momentarily then changes back to the curre2. See PROBLEM section TEMPERATURES ARE TOO WARM Turn on household water line valve If it is replace the ice amp water filter cartridge Move item and release wire signal arm Remove any ice cubes that are frozen together over the wire signal arm Ice maker is not separating the ice cubes Ice cubes are not being used frequently enough Ice cubes are hollow or smaller than normal Remove and shake ice container to separate cubes The ice amp water filter cartridge may be clogged Replace filter cartridge Ice has bad odor and taste Ice has picked up odor or flavor from strong food stored in refrigerator or freezer Water running to ice maker has poor taste or odor Ice not used frequently enough Cover foods tightly Discard stale ice Ice maker will produce fresh supply Add filter to water supply line Consult a water purifying company Discard stale ice ICE DISPENSER Dispenser will not dispense ice Ice storage container is empty Freezer temperature is set too warm Household water line valve is not open Freezer door is not closed Ice dispensing arm has been held in for more than 4 5 minutes When the first supply of ice is dropped into the container the dispenser should operate Turn freezer control to a higher setting so that ice cubes will be made When first supply of ice is made dispenser should operate Open household water line valve Allow sufficient time f
3. Stop ice production by lifting the wire signal arm to the up or OFF position side mounted or the ice maker s On Off power switch turned Off set to the O position rear mounted Remove ice container by lifting up and out Empty and carefully clean the container with mild detergent Rinse with clear water Do not use harsh or abrasive cleaners Allow ice container to dry completely before replacing in the freezer Remove ice chips and clean the shelf and chute that supports the ice container Replace the ice container Lower the wire signal arm on the ice maker to the down or ON position side mounted or the ice maker s On Off power switch is turned On set to the I position rear mounted and the ice maker will resume production a WARNING Do not use the ice chute as a handle when removing or replacing the ice storage bin Surfaces there may be sharp Do not put fingers up ice chute Surfaces there may be sharp 14 IMPORTANT When removing or replacing the ice bin do not rotate the auger in the ice bin If the auger is accidentally turned you must realign the auger by turning it in 90 turns until the ice bin fits into place with the drive mechanism Remove and empty the ice storage bin if 1 An extended power failure one hour or longer causes ice cubes in the ice storage bin to melt and freeze together and jam the dispenser mechanism The ice dispenser is not used frequently Ice c
4. Do not store or use gasoline or other flammable liquids in the vicinity of this or any other appliance Read product labels for warnings regarding flammability and other hazards e Do not operate the refrigerator in the presence of explosive fumes e Avoid contact with any moving parts of automatic ice maker e Remove all staples from the carton Staples can cause severe cuts and also destroy finishes if they come in contact with other appliances or furniture CHILD SAFETY Destroy or recycle the carton plastic bags and any exterior wrapping material immediately after the refrigerator is unpacked Children should NEVER use these items to play Cartons covered with rugs bedspreads plastic sheets or stretch wrap may become airtight chambers and can quickly cause suffocation PROPER DISPOSAL OF YOUR REFRIGERATOR OR FREEZER Risk of child entrapment Child entrapment and suffocation are not problems of the past Junked or abandoned refrigerators or freezers are still dangerous even if they will sit for just a few days If you are getting rid of your old refrigerator or freezer please follow the instructions below to help prevent accidents Before you throw away your old refrigerator freezer e Remove doors e Leave shelves in place so children may not easily climb inside e Have refrigerant removed by a qualified service technician a WARNING These Guidelines Must Be Followed To Ensure That Sa
5. Foods for Freezing e To minimize dehydration and quality deterioration use aluminum foil freezer wrap freezer bags or airtight containers Force as much air out of the packages as possible and seal them tightly Trapped air can cause food to dry out change color and develop an off flavor freezer burn e Wrap fresh meats and poultry with suitable freezer wrap prior to freezing e Do not refreeze meat that has completely thawed Loading the Freezer e Avoid adding too much warm food to the freezer at one time This overloads the freezer slows the rate of freezing and can raise the temperature of frozen foods e Leave a space between the packages so cold air can circulate freely allowing food to freeze as quickly as possible e Avoid storing hard to freeze foods such as ice cream and orange juice on the freezer door shelves These foods are best stored in the freezer interior where the temperature varies less 18 NORMAL OPERATING SOUNDS amp SIGHTS UNDERSTANDING THE SOUNDS YOU MAY HEAR Your new high efficiency refrigerator may make unfamiliar sounds These are all normal sounds and soon will become familiar to you They also indicate your refrigerator is operating A Evaporator The flow of refrigerant through the evaporator may create a boiling or gurgling sound B Evaporator Fan as designed Hard surfaces such as vinyl or wood floors walls and kitchen cabinets may make sounds more noticeable Listed bel
6. Ice maker is not making e Ice maker wire signal armis in e Move wire signal arm to the down or ON position any ice the up or OFF position side mounted e Ice maker power switch is Off e Turn power switch to On I position rear mounted e Household water line valve is e Turn on household water line valve not open e Freezer is not cold enough e See PROBLEM section TEMPERATURES ARE TOO WARM e Saddle valve on cold water e Turn off household water line valve Remove valve pipe is clogged or restricted by Ensure that valve is not a self piercing saddle valve foreign material Clean valve Replace valve if necessary e Check to see if the water e If not the ice amp water filter cartridge is clogged or dispenser is dispensing water restricted by foreign material and must be replaced 24 BEFORE YOU CALL CONTINUED PROBLEM CAUSE CORRECTION AUTOMATIC ICE MAKER CONTINUED Ice maker is not making enough ice Ice maker will not stop making ice Ice maker is producing less ice than you expect Freezer is not cold enough Household water line valve is not completely open Check to see if water dispenser is dispensing slower than normal Ice maker wire signal arm is being held down by some item in the freezer Ice maker should produce approximately 4 5 pounds of ice every 24 hours Extra Ice should produce up to 8 pounds of ice every 24 hours
7. filter please read the following use and care information This ice and water filter system filters water to your ice maker and water dispenser It is located in the upper right front corner of the fresh food compartment System Startup Water supply does not need to be turned off however do not use ice and water dispenser while installing filter The filter cartridge has already been installed in the filter housing at the factory Refer to the How The Water Dispenser Works section to properly fill the system with water Order new filter cartridges through the dealer where you bought the refrigerator contact the Consumer Assistance Center at 1 800 944 9044 or go to our web site at www frigidaire com It might be good to order some filter cartridges when you first install your refrigerator Be sure to ask for the FC 100 PureSource replacement cartridge Push In l and Click Push Button To Install To Release The PureSource2 Ice and Water Filter System NGFC 2000 with the PureSource2 cartridge FC 100 is tested and certified by NSF International the nationally recognized and respected not for profit certification organization for public health safety The PureSource2 Filter system is tested and certified to ANSI NSF Standards 42 and 53 See performance data sheet for specifications This system should not be used on water that is microbiologically unsafe or with water of unknown quali
8. s On Off power switch is turned ask for the RG 100 On set to the I position rear mounted PureSource TVSH Remove 10 Check for leaks Open refrigerator door Wipe any water droplets replacement cartridge from the filter cup Fill a glass with water If there is a leak unscrew filter cup and reinsert the filter cartridge Check The PureSource NGRG 2000 Ice and Water placement of large O ring Reinstall filter cup making certain it is Filter System with the RG 100 cartridge is tested tightened completely and certified by NSF International the nationally 11 To condition filter system and purge air from water line fill a recognized and respected not for profit glass with water Continue flushing the system for approximately certification organization for public health safety 3 minutes to assure that the purest water possible is stored in The PureSource system is tested and certified to ANSI NSF the water tank Standard 42 See performance data sheet for specifications IMPORTANT This system should not be used on water that is Resetting The Filter Status Light some models microbiologically unsafe or with water of unknown quality unless the water has been adequately disinfected before or after traveling through the filtration system After replacing the filter cartridge it will be necessary to press the Filter Status reset button located on the ice and water dispenser This will reset the Filter Status lig
9. temperatures fall below freezing e Chemicals from a malfunctioning softener can damage the ice maker If the ice maker is connected to soft water ensure that the softener is maintained and working properly IMPORTANT Ensure that your water supply line connections comply with all local plumbing codes Before Installing The Water Supply Line You Will Need Basic Tools adjustable wrench flat blade screwdriver and Phillips screwdriver Access to a household cold water line with water pressure between 30 and 100 psi A water supply line made of inch 6 4 mm OD copper tubing To determine the length of copper tubing needed you will need to measure the distance from the ice maker inlet valve at the back of the refrigerator to your cold water pipe Then add approximately 7 feet 2 1 meters so the refrigerator can be moved out for cleaning as shown A shutoff valve to connect the water supply line to your household water system DO NOT use a self piercing type shutoff valve A compression nut and ferrule sleeve for connecting the water supply line to the ice maker inlet valve NOTE Water line kit number 5303917950 available from your appliance dealer at additional cost contains 25 feet 7 6 meters of inch OD copper tubing a saddle type shutoff valve nonpiercing 2 4 inch brass compression nuts 2 ferrules sleeves and instructions for installing a water supply line To Connect Water Supply Line To Ic
10. the second set of tabs are free Continue this process until all tabs are free and the toe grille can be removed See graphic at top of page in right column LEVELING All four corners of your refrigerator must rest firmly on a solid floor Your refrigerator is equipped with adjustable front rollers to help level your unit To ensure proper door seal and assist door closing the refrigerator should be tilted 1 4 6 mm front to back To Level Your Refrigerator 1 Remove toe grille See To Remove Toe Grille 2 Use flat blade screwdriver or 3 8 socket wrench to adjust front rollers Cabinet NOTE The refrigerator doors are designed to shut by themselves within a 20 degree opening 3 Raise Pa O 0 q 3 Check both doors to be sure seals touch cabinet on all four sides oy INSTALLATION CONNECTING ICE MAKER TO WATER SUPPLY ZN WARNING To avoid electric shock which can cause death or severe personal injury disconnect the refrigerator from electrical power before connecting a water supply line to the refrigerator CN caution To Avoid Property Damage e Copper tubing is recommended for the water supply line Water supply tubing made of 1 4 plastic is not recommended since it greatly increases the potential for water leaks Manufacturer will not be responsible for any damage if plastic tubing is used for supply line e DONOT install water supply tubing in areas where
11. Freezer warm hours for temperature to stabilize temperature is satisfactory Temperature in the Meat e Meat Keeper Temperature e Adjust Meat Keeper Temperature Control to a colder Keeper is too warm some Control is set too warm setting models WATER MOISTURE FROST INSIDE REFRIGERATOR Moisture collects on inside e Weather is hot and humid e The rate of frost buildup and internal sweating of refrigerator walls increases e Door is slightly open e See PROBLEM section OPENING CLOSING OF DOORS DRAWERS e Door is opened too often or too e Open door less often long Open containers Keep containers covered Water collects on bottom e Vegetables contain and give e Itis not unusual to have moisture on the bottom side of side of drawer cover off moisture the cover e Move humidity control some models to lower setting Water collects in bottom of e Washed vegetables and fruit e Dry items before putting them in the drawer Water drawer drain while in the drawer collecting in bottom of drawer is normal WATER MOISTURE FROST OUTSIDE REFRIGERATOR Moisture collects on e Weather is humid e This is normal in humid weather When humidity is outside of refrigerator or lower the moisture should disappear between doors e Door is slightly open causing e See PROBLEM section OPENING CLOSING OF cold air from inside refrigerator DOORS DRAWERS to meet warm air from outside AUTOMATIC ICE MAKER
12. MPORTANT Resetting The Filter Status Light some models After replacing the filter cartridge it will be necessary to press the Filter Reset button located on the ice and water dispenser This will reset the Filter Status light Push the reset button until the green red and amber lights flash 10 15 seconds Please refer to the complete dispenser operating instructions attached to the inside of the freezer door White Westinghouse uses the name CrystalClear instead of PureSource but they are the same filter AUTOMATIC ICE AND WATER DISPENSER PURESOURCE MB ICE AND WATER FRONT FILTER filter before reinstalling the refrigerator The dispenser system SOME MODELS will also operate without filtration with filter cartridge removed and bypass installed NOTE To change filter If you purchased a refrigerator with a PureSource MB It is not necessary to turn the water supply off to change the Ice and Water front filter please read the following use filter and care information This ice and water filter system 7 s 1 Set ice maker wire signal arm to the OFF up position side filters water to your ice maker and water dispenser It is g up p located in the upper right front corner of the fresh food mounted x ne ice maker s On Off power switch turned Off set compartment to the O position rear mounted 2 Push the Filter Release Button located to the right of the System Startup filter cartridge to release the filt
13. NSES RESULTING FROM ANY BREACH OF THIS WRITTEN OR ANY IMPLIED WARRANTY Note Some states do not allow the exclusion or limitation of incidental or consequential damages so this limitation or exclusion may not apply to you Service calls which do not involve malfunction or defects in workmanship or material or for appliances not in ordinary household use The consumer shall pay for such service calls Damages caused by services performed by servicers other than Electrolux or its authorized servicers use of parts other than genuine Electrolux parts obtained from persons other than such servicers or external causes such as abuse misuse inadequate power supply or acts of God Products with original serial numbers that have been removed or altered and cannot be readily determined Keep your bill of sale delivery slip or some other appropriate payment record The date on the bill establishes the warranty period should service be required If service is performed it is in your best interest to obtain and keep all receipts This written warranty gives you specific legal rights You may also have other rights that vary from state to state Service under this warranty must be obtained by contacting Electrolux This warranty only applies in the 50 States of the U S A and Puerto Rico and Canada Product features or specifications as described or illustrated are subject to change without notice USA 800 944 9044 Electrolux Major Appl
14. PERS SOME MODELS The crispers located under the bottom refrigerator shelf are designed for storing fruits vegetables and other fresh produce Wash items in clear water and remove excess water before placing them in the crispers Items with strong odors or high moisture content should be wrapped before storing DELI DRAWER SOME MODELS Some models are equipped with a Deli Drawer for storage of luncheon meats spreads cheeses and other deli items MEAT KEEPER SOME MODELS Some models are equipped with a Meat Keeper Meat Keeper temperatures can be adjusted by sliding the Meat Keeper Temperature Control in either direction Use this pan for short term storage of bulk meat items If meats are to be kept longer than one or two days they should be frozen The Meat Keeper is fixed and cannot be moved up or down If fruits or vegetables are to be stored in the Meat Keeper set the Meat Keeper Temperature Control to a warmer setting to prevent freezing Crisper Drawer HUMIDITY CONTROL SOME MODELS The Humidity Control present on some models with crisper drawers allows you to adjust the humidity within the crisper This can extend the life of fresh vegetables that keep best in high humidity Colder Meat Keeper with NOTE Temperature Control Leafy vegetables keep best when stored with the Humidity Control set on Higher Humidity or in a drawer without a Humidity Control This keeps incoming air to a min
15. Side by Side Refrigerator With Electronic Controls Espanol 27 Welcome 00 2 Safety Instructions 3 Installation includes Connecting Ice Maker To Water Supply Door Removal Instructions 6 iene Ag Li ey ba Features at a Glance Temperature Controls 7 9 Looking Inside 10 11 Automatic Ice and Water Dispenser Food Storage amp Energy Saving Tips 18 opED 0 Normal Operating Sounds 19 Care amp Cleaning 20 21 Warranty 22 Before You Call Solutions to Common Problems 23 26 METES READ AND SAVE THESE INSTRUCTIONS P N 241660600 0505 WELCOME amp CONGRATULATIONS Congratulations on your purchase of a new refrigerator We here at Electrolux Home Products Inc are very proud of our product and we are completely committed to providing you with the best service possible Your satisfaction is our 1 priority Please read this Use amp Care Manual very carefully It contains valuable information on how to properly maintain your new refrigerator We know you ll enjoy your new refrigerator and Thank You for choosing our product We hope you consider us for future purchases PLEASE READ AND SAVE THESE INSTRUCTIONS This Use amp Care Manual provides specific operating instructions for your m
16. d Please order new one Red Air filter is 100 percent used Please change now TURNING THE COOLING SYSTEM ON AND OFF You can disable the cooling system in your refrigerator by pressing the On Off button located on the left side of the temperature control panel Freezer Temp Fresh Food Temp A To ensure that you do not accidentally turn off the cooling system the button does not work unless you press and hold it One for three seconds On Off While the cooling system is OFF the digital display will show OF OF for temperature display models and O F for numeric display models Once you disable the cooling system all refrigeration to the freezer and fresh food compartments stops To turn the cooling system back on you must again press and Cooling System On Off Button hold the On Off button for three more seconds IMPORTANT The On Off button only controls your refrigerator s cooling system Power to lights and other electrical components continue unless you unplug the power cord LOOKING INSIDE PIZZA SHELF SOME MODELS This shelf is attached to the freezer wall beside the ice dispenser container This convenient area allows for storage of pizza and other tall items placed vertically between the ice dispenser container and the freezer wall ICE CREAM SHELF SOME MODELS This shelf attaches to the top of the ice dispenser container It allows storage of both round and r
17. division of Electrolux Canada Corp Electrolux Home Products Inc and E servicer NORMAL RESPONSIBILITIES OF THE CUSTOMER 1 2 EXCLUSIONS IF YOU NEED SERVICE lectrolux Canada Corp are referred to in this warranty as Electrolux We authorize no person to change or add to any of our obligations under this warranty Our obligations for service and parts under this warranty must be performed by us or an authorized Electrolux This warranty applies only to products in ordinary household use and the consumer is responsible for the items listed below 3 4 5 6 Proper use of the appliance in accordance with instructions provided with the product Proper installation by an authorized servicer in accordance with instructions provided with the appliance and in accordance with all local plumbing electrical and or gas codes Proper connection to a grounded power supply of sufficient voltage replacement of blown fuses repair of loose connections or defects in house wiring Expenses for making the appliance accessible for servicing such as removal of trim cupboards shelves etc which are not a part of the appliance when it was shipped from the factory Damages to finish after installation Replacement of light bulbs and or fluorescent tubes on models with these features This warranty does not cover the following 1 4 CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL EXPE
18. e Maker Inlet Valve 1 Disconnect refrigerator from electric power source 2 Place end of water supply line into sink or bucket Turn ON water supply and flush supply line until water is clear Turn OFF water supply at shutoff valve 3 Unscrew plastic cap from water valve inlet and discard cap 4 Slide brass compression nut then ferrule sleeve onto water supply line as shown 5 Push water supply line into water valve inlet as far as it will go 14 inch Slide ferrule sleeve into valve inlet and finger tighten compression nut onto valve Tighten another half turn with a wrench DO NOT over tighten 6 With steel clamp and screw secure water supply line to rear panel of refrigerator as shown 7 Coil excess water supply line about 2 turns behind refrigerator as shown and arrange coils so they do not vibrate or wear against any other surface 8 Turn ON water supply at shutoff valve and tighten any connections that leak Reconnect refrigerator to electrical power source 10 To turn ice maker on lower wire signal arm side mounted or set the ice maker s On Off power switch to the P position rear mounted Plastic Water Tubing to Ice Maker 4 Steel x Fill Tube Clamp Brass Compression Nut Ferrule Sleeve d re Copper water line Water Valve Bracket Valve Inlet Water Valve Copper water line from household water supply Include enough tubing in loop to al
19. eaners Clean stainless steel front and handles with non abrasive soapy water and a Stainless Steel dishcloth Rinse with clean water and a soft cloth Wipe stubborn spots with an Models Only ammonia soaked paper towel and rinse Use a non abrasive stainless steel cleaner These cleaners can be purchased at most home improvement or major department stores Always follow manufacturer s instructions NOTE Always clean wipe and dry with the grain to prevent cross grain scratching Wash the rest of the cabinet with warm water and mild liquid detergent Rinse well and wipe dry with a clean soft cloth 20 CARE amp CLEANING CONTINUED CN caution Wear gloves when replacing light bulbs to avoid getting O fi cut REPLACING LIGHT BULBS 1 Unplug refrigerator 2 Wear gloves as protection against possible broken glass Refrigerator Light 3 Remove light cover if necessary Located behind 4 Unscrew and replace old bulb with an appliance bulb of control panel the same wattage 5 Replace light cover if necessary Refrigerator Light Replacement 6 Remember to plug the refrigerator back in Crisper Light Light Socket Crisper Light Cover Located Behind Cover Left Rear ate of Crispers g Light Socket Located Behind Left Rear of Crispers 7 or CP Light Socket Located Behind Right Light Bulb Rear of Ice Container Crisper Light Replacement Models may vary Freezer Light Replacement Vacation and Mo
20. ectangular cartons of your favorite ice cream TIP UP SHELF SOME MODELS A Tip Up shelf in the freezer section allows tall items to be easily stored Pizza Shelf lt a Ss i Ice Cream Shelf IN caution To avoid personal injury or property damage handle tempered glass shelves carefully Shelves may break suddenly if nicked scratched or exposed to sudden temperature change ADJUSTABLE DOOR BINS Some models have adjustable door bins that can be moved to suit individual needs To move door bins Lift bin straight up Remove bin Place bin in desired position Lower bin onto supports until locked in place PFoONs Adjustable Door Bin WhiteWestinghouse SpillFree 10 CANTILEVER SHELF ADJUSTMENT Refrigerator shelves are easily adjusted to suit individual needs Before adjusting the shelves remove all food Cantilever shelves are supported at the back of the refrigerator To adjust cantilever shelves Lift front edge up g Pull shelf out Replace the shelf by inserting the hooks at rear of the shelf into the wall bracket Lower the shelf into the desired slots and lock into position SpillSafe glass shelves some models catch and hold accidental spills In some models the SpillSafe shelves slide out for easy access to food and for fast cleaning The shelves slide out independently of their mounting brackets Just pull the front of the
21. er from the housing To Water supply does not need to be turned off however do not minimize the possibility of the filter falling out of the use ice and water dispenser while installing filter housing during removal it would be best to hold the filter as it moves out toward you The filter cartridge has already been installed in the filter housing at the factory Refer to the How The Water Dispenser NOTE Works section to properly fill the system with water Order new filter A small amount of water may be released during this cartridges through the operation You should have a paper towel or dish cloth dealer where you handy to wipe up any water that may drip out of the filter or bought the refrigerator housing Two small holes near the back of the housing contact the Consumer have been added for any excess water to escape It would Assistance Center at 1 be best to clear away any food near this area on the top 800 944 9044 or go to shelf in advance of removing the filter our web site at www frigidaire com It might be good to order some filter cartridges when you first install w Pull the old filter cartridge straight out of the housing 4 Discard the old filter 5 Remove the new filter cartridge from the packaging and Push In your regain Be and Ciok Push Button a ei the filter housing the same way the old one eae aoe 6 When the cartridge is almost in you will feel it stop against cartridge the c
22. erator is touching a wall or cabinet Food is touching shelf on top of drawer Track that drawers slide on is dirty Close both doors gently Ensure floor is level and solid and can adequately support the refrigerator Contact a carpenter to correct a sagging or sloping floor Ensure floor is level and solid and can adequately support the refrigerator Contact a carpenter to correct a sagging or sloping floor Keep less food in drawer Clean drawer rollers and track See Care amp Cleaning Chart in Care and Cleaning section Light bulb is not on e Light bulb is burned out Light switch is stuck No electric current is reaching refrigerator See Replacing Light Bulbs in Care and Cleaning section Light switch is located on side of refrigerator and freezer liners See PROBLEM section RUNNING OF REFRIGERATOR loss of power or a low voltage condition IF YOU HEAR 5 beeps e Adoor has been left open for 5 These beeps will repeat once every minute until the minutes or more door has been closed This is normal for the Door Ajar alarm 3 beeps e The refrigerator has experienced a This is normal when Power On Reset is activated 26
23. erature to stabilize See solution above Food stored in Meat Keeper freezes some models Meat Keeper Temperature Control set too cold Adjust Meat Keeper Temperature Control to a lower setting Meat should be stored at a temperature just below the freezing point for maximum fresh storage time It is normal for ice crystals to form due to the moisture content of meat Digital temperature displays are flashing Electronic control system has detected a performance problem 23 Call your Electrolux service representative who can interpret any messages or number codes flashing on the digital displays BEFORE YOU CALL CONTINUED PROBLEM CAUSE CORRECTION TEMPERATURES ARE TOO WARM Freezer Refrigerator e Doors are opened too temperature is too warm frequently or too long e Door is slightly open e Warm air enters the refrigerator whenever the door is opened Open the door less often e See PROBLEM section OPENING CLOSING OF DOORS DRAWERS e Clean condenser See Care amp Cleaning Chart in Care and Cleaning section e Condenser is dirty Freezer temperature is too e Freezer control is set too warm Refrigerator warm temperature is satisfactory e Set freezer control to a colder setting Allow 24 hours for temperature to stabilize Refrigerator temperature is e Refrigerator control is set too e Set refrigerator control to a colder setting Allow 24 too warm
24. ezer compartment After the refrigerator is installed properly and has cooled for several hours the ice maker can begin making ice within 24 hours Air in new plumbing lines may cause the ice maker to cycle two or three times before making a full tray of ice To begin ice production lower the wire signal arm to the down or ON position With no usage it will take approximately 2 days to fill the ice container The ice maker turns off automatically when the ice container becomes full To stop the ice maker lift the wire signal arm until it clicks and locks in the up or OFF position HOW THE ICE DISPENSER WORKS REAR MOUNTED The ice maker and container are located in the top of the freezer compartment After the refrigerator is installed properly and has cooled for several hours the ice maker can begin making ice within 24 hours Air in new plumbing lines may cause the ice maker to cycle two or three times before making a full tray of ice Ice production is controlled by the ice maker s On Off power switch Press the switch to the 13 q O position to turn it Off and press it to the I position to turn it On With no usage it will take approximately 2 days to fill the ice container The ice maker also has a built in wire signal arm which automatically stops ice production when the ice bin is full This signal arm should not be used to manually stop the ice maker The ice maker produces 4 to 6 pounds
25. fety Mechanisms In This Refrigerator Will Operate Properly ELECTRICAL INFORMATION The refrigerator must be plugged into its own dedicated 115 Volt 60 Hz AC only electric outlet The power cord of the appliance is equipped with a three prong grounding plug for your protection against electrical shock hazards It must be plugged directly into a properly grounded three prong receptacle The receptacle must be installed in accordance with local codes and ordinances Consult a qualified electrician Do not use an extension cord or adapter plug If the power cord is damaged it should be replaced by the manufacturer service technician or a qualified person to prevent any risk Never unplug the refrigerator by pulling on the power cord Always grip the plug firmly and pull straight out from the receptacle to prevent damaging the power cord Unplug the refrigerator before cleaning and before replacing a light bulb to avoid electrical shock Performance may be affected if the voltage varies by 10 or more Operating the refrigerator with insufficient power can damage the compressor Such damage is not covered under your warranty Do not plug the unit into an outlet controlled by a wall switch or pull cord to prevent the refrigerator from being turned off accidentally Avoid connecting refrigerator to a Ground Fault Interruptor GFI circuit IMPORTANT Pressing and holding the On Off button for 3 seconds located on the left side of
26. ht Push the reset button until the green red and amber lights flash 10 15 seconds Please refer to the complete dispenser operating instructions attached to the inside of the freezer Changing the Filter door On models without a Filter Status reset bution there is a set of Reminder Stickers included in the envelope that the Use amp Care Manual came in Choose a dated sticker that indicates 6 9 months depending on your water quality and usage from the date of installation Place the sticker on the front of the filter cup to remind you when it is time to change the filter e Rated Capacity 400 gallons e Rated service flow 5 GPM e Maximum Rated Pressure 100 PSI e Maximum Operating Temp 100 F Water conditions vary throughout the world but changing the water filter every 6 9 months normally will ensure the highest possible water quality The Filter Status light will turn red after 400 gallons of water has flowed through the ice and water dispenser some models Also if the filter has been in a refrigerator that has not been in use for awhile during moving for example change the filter before reinstalling the refrigerator White Westinghouse uses the name CrystalClear instead of PureSource but they are the same filter 15 AUTOMATIC ICE AND WATER DISPENSER PURESOURCE2 ICE AND WATER FRONT FILTER SOME MODELS NOTE If you purchased a refrigerator with a PureSource2 Ice and Water front
27. iances North America a division of Electrolux Home Products Inc P O Box 212378 Augusta GA 30917 Canada 800 265 8352 Electrolux Major Appliances North America a division of Electrolux Home Products Inc 5855 Terry Fox Way Mississauga Ontario L5V 3E4 22 BEFORE YOU CALL 1 800 944 9044 United States 1 800 265 8352 Canada Visit our web site at www frigidaire com PROBLEM CAUSE CORRECTION RUNNING OF REFRIGERATOR Compressor does not run Freezer control is set to OF Refrigerator is in defrost cycle Plug at wall outlet is disconnected House fuse blown or tripped circuit breaker Power outage Set freezer control See Temperature Controls section This is normal for a fully automatic defrost refrigerator The defrost cycle occurs periodically lasting about 30 minutes Ensure plug is tightly pushed into outlet Check replace fuse with a 15 amp time delay fuse Reset circuit breaker Check house lights Call local Electric Company Refrigerator runs too much or too long Room or outside weather is hot Refrigerator has recently been disconnected for a period of time Automatic ice maker is operating Doors are opened too frequently or too long Refrigerator freezer door may be slightly open Freezer control is set too cold control found in refrigerator section Refrigerator freezer gasket is dirty worn cracked or poorly fi
28. ice maker connect a water supply immediately or turn the Ice maker off by lifting the wire signal arm to the up or OFF position side mounted or the ice maker s On Off power switch turned Off set to the O position rear mounted I Drain Pan not removable You may hear water running into the drain pan during the defrost cycle J Condenser May create minimal sounds from forced air K Motorized Damper May produce a light humming during operation 19 CARE amp CLEANING Keep your refrigerator and freezer clean to prevent odor build up Wipe up any spills immediately and clean both sections at least twice a year Never use metallic scouring pads brushes abrasive cleaners or strong alkaline solutions on any surface Do not wash any removable parts in a dishwasher Always unplug the electrical power cord from the wall outlet before cleaning a CAUTION e When moving the refrigerator pull straight out Do not shift the refrigerator from side to side as this may damage the floor Be careful not to move the refrigerator beyond the plumbing connections e Damp objects stick to cold metal surfaces Do not touch refrigerated surfaces with wet or damp hands e Never use CHLORIDE to clean stainless steel NOTE e The On Off button on the Electronic Control only controls your refrigerators cooling system To turn off power to your refrigerator you must unplug the power cord from the wall outlet e Do not use razor blades or
29. imum and maintains maximum moisture content Wine Rack WINE RACK SOME MODELS The wine rack stores bottles of T UUU wine or single two liter plastic Higher umiai Lower Humidit bottles of juice or soda pop To as mamas install slide the Wine Rack onto the shelf with the curve facing in To remove slide the Crisper Humidity Control Wine Rack out Install on either side of shelf D 11 AUTOMATIC ICE AND WATER DISPENSER AUTOMATIC ICE amp WATER DISPENSER OPERATING INSTRUCTIONS 9 00000 cnc tute Cbe Crah Light etd 22000080 wictY Y WATER o o Features may vary according to model EXTREME To freeze food at a faster rate to preserve freshness push the Touch Pad 1 for 3 5 seconds to FREEZE activate this feature A green light will appear above the Touch Pad Push the Touch Pad again for 3 5 seconds to deactivate EXTRA To increase ice production for special occasions such as parties push the Touch Pad Oio ICE 3 5 seconds to activate this feature A green light will appear above the Touch Pad Push the Touch Pad 2 again for 3 5 seconds to deactivate CUBE Press the CUBE Touch Pad to get cubed ice A green light will appear above the Touch Pad Press glass against ICE dispensing paddle as far up as possible to catch all ice CRUSH Press the CRUSH Touch Pad to get crushed ice A green light will appear above
30. is stored in the water storage tank e Rated service flow 5 GPM e Maximum Rated Pressure 100 PSI e Maximum Operating Temp 100 F IMPORTANT Resetting The Filter Status Light some models Changing the Filter Water conditions vary throughout the world but changing the After replacing the filter cartridge it will be necessary to water filter every press the Filter Reset button located on the ice and water 6 9 months normally will ensure the highest possible water dispenser This will reset the Filter Status light Push the reset quality The Filter Status light will turn red after approximately button until the green red and amber lights flash 10 15 250 gallons of water has flowed through the ice and water seconds Please refer to the complete dispenser operating dispenser Also if the filter has been in a refrigerator that has not instructions attached to the inside of the freezer door been in use for awhile during moving for example change the White Westinghouse uses the name CrystalClear instead of PureSource but they are the same filter 17 FOOD STORAGE amp ENERGY SAVING IDEAS FOOD STORAGE IDEAS ENERGY SAVING IDEAS e Locate the refrigerator in the coolest part of the room out of direct sunlight and away from heating ducts or registers Do not place the refrigerator next to heat producing appliances such Fresh Food Storage e The fresh food compartment should be kept between 34 F and 40 F w
31. ith an optimum temperature of 37 F e Avoid overcrowding the refrigerator shelves This reduces the circulation of air around the food and results in uneven as a range oven or dishwasher If this cooling is not possible a section of cabinetry or an added layer of Fruits and Vegetables insulation between the two appliances will help the refrigerator e Storage in the crisper drawers traps moisture to help operate more efficiently preserve the fruit and vegetable quality for longer time e Level the refrigerator so that the doors close tightly periods e Refer to this Use amp Care Manual for the suggested Meat temperature control settings Periodic cleaning of the condenser will help the refrigerator run more efficiently See the Care and Cleaning Chart on page 20 e Do not overcrowd the refrigerator or block cold air vents e Raw meat and poultry should be wrapped securely so leakage and contamination of other foods or surfaces does not occur Frozen Food Storage Doing so causes the refrigerator to run longer and use e The freezer compartment should be kept at 0 F or lower more energy e A freezer operates most efficiently when it is at least 2 3 e Cover foods and wipe containers dry before placing them full in the refrigerator This cuts down on moisture build up inside the unit e Organize the refrigerator to reduce door openings Remove as many items as needed at one time and close the door as soon as possible Packaging
32. l you hear a click Filter should be flush with cabinet Water has an odd taste and or odor Water has been in the tank for a period of time Unit not properly connected to cold water line Tubing used in the household water supply and installation may affect water taste and odor Water has a high mineral content Draw and discard 10 12 glasses of water to freshen the supply and completely rinse out the tank Connect unit to cold water line that supplies water to the kitchen faucet For best results use copper tubing for water connections Contact water treatment plant for help Water pressure is e extremely low Cut off and cut on pressures are too low well systems only Reverse osmosis system is in regenerative phase Have someone turn up the cut off and cut on pressure on the water pump system well systems only It is normal for a reverse osmosis system to be below 20 psi during the regenerative phase ODORS IN REFRIGERATOR Interior is dirty Interior needs to be cleaned Food with strong odors is in refrigerator See Care amp Cleaning Chart in Care and Cleaning section Cover food tightly OPENING CLOSING OF DOORS DRAWERS Door s will not close e Drawers are difficult to move LIGHT BULB IS NOT ON Door was closed too hard causing other door to open slightly Refrigerator is not level It rocks on the floor when moved slightly Refrig
33. lip assembly in the back of the housing The clip assembly holds the filter cartridge firmly in place At this The PureSource MB Ice and Water Filter System point you wil neat to push tirmily uot the cartridge MBFC 2003 with the PureSource MB cartridge snaps fully in place When completely in place the front of NSF WF2CBMB is tested and certified by NSF the filter cartridge will be flush with the front of the housing International the nationally recognized and 7 Set ice maker wire signal arm to the ON down position side respected not for profit certification organization mounted or the ice makers On Off power switch is turned On for public health safety The PureSource MB Filter system is set to the 1 position rear mounted tested and certified to ANSI NSF Standards 42 and 53 See 8 performance data sheet for specifications This system should not be used on water that is microbiologically unsafe or with water of unknown quality unless the water has been adequately disinfected before or after traveling through the Fill a glass with water As you are doing this check for leaks at the filter housing There will be noticable spurts and sputters as the system pushes the air out through the system and out the dispenser nozzle This is normal filtration system 9 After you have run one glass of water continue to flush the system for approximately 3 minutes to assure that the e Rated Capacity 250 gallons purest water possible
34. low moving refrigerator out for cleaning IMPORTANT It takes approximately 24 hours for the ice maker to begin producing ice Air in new plumbing lines may cause ice maker to cycle two or three times before making a full tray of ice New plumbing may cause ice to be discolored or have poor flavor Discard ice made during the first 24 hours DOOR REMOVAL INSTRUCTIONS Top Hinge Top Hinge Screw Cover Screw Bottom Hinge Screw Cover Screw Top Hinge Cover Door Hinge Assembly TO DISCONNECT 1 Press outer ring against face of fitting OS es remove tube TO CONNECT meee Insert tube and push until mark touches face of fitting Tools Necessary Phillips head o Wrench Set Q i Ve x 38 Adjustable Fixed Wrench Wrench DOOR REMOVAL INSTRUCTIONS If it is necessary to move the refrigerator through narrow doorways follow these steps to remove the doors NOTE Before you begin turn Freezer and Fresh Food controls to OFF by pressing and holding the On Off button for 3 seconds and remove electrical power cord from wall outlet Remove any food from door shelves 1 Disconnect electrical supply 2 Open both doors then remove toe grille 3 Close doors To Remove Refrigerator Door 1 Remove top hinge cover screw on refrigerator door and remove cover 2 Trace around hinge with soft lead pencil This will make it easier to
35. m Shelf Ice Maker SpillProof Aspect Shelf Fixed Door Bin Water Filter CAUTION Do Not Remove m Magnet Behind Dairy Compartment Dairy Compartment Ice Container Door Bin i i SpillProof Shalt i Sliding Shelt i H Door Bin i i Tall Bottle Shelf i Retainer Tilt Out fj i Door Bin i Door Bin Small Basket i Special Item Rack Large Glide Out Meat Keeper Basket and Cover Tilt Out Can Rack Door Bin Large Basket Tilt Out Door Bin Y ALLOWING COOLING TIME BEFORE USE Toe Grille TEMPERATURE CONTROLS Crisper Pan and Cover Fixed Door Bin To ensure reliable food storage allow your refrigerator and freezer to operate with the doors closed for 8 to 12 hours before placing food inside During this cooling period you do not need to adjust the controls which are preset at the factory SETTING COOLING TEMPERATURES Your refrigerator comes with a state of the art electronic digital control system The system s control panel is located at the top of the the fresh food compartment
36. nt temperature CHOOSING FAHRENHEIT OR CENTIGRADE Depending on which temperature standard you prefer to use you can set your control panel to display in fahrenheit or centigrade To change between fahrenheit and centigrade press the Mode button located between the two digital temperature displays Freezer Temp Fresh Food Temp Press to alternate between Fahrenheit and Centigrade Temperature Adjustment Guide If Fresh Food compartment is too warm If Fresh Food compartment is too cold If Freezer compartment is too warm If Freezer compartment is too cold MAKING TEMPERATURE ADJUSTMENTS After running your refrigerator for 24 hours you can adjust temperatures as needed Make your adjustments small and gradual allowing time for temperatures to change and stabilize Refer to the following guidelines for temperature settings WHAT TO DO IF THE TEMPERATURE DISPLAYS FLASH If either display is continuously flashing it may indicate that the control system has detected a performance problem Call your Electrolux service representative who can interpret the flashing message Numeric Display Freezer ia Warmest 1 1 Factory Setting 6 6 Coldest 9 9 Temperature Display 2 Digit Freezer Fresh Food F C F C Warmest f 6 14 47 8 Factory Setting 0 18 I 37 3 Coldest 6 21 33 ili Adjust Fresh Food control one degree colder by pressing Down Colder button Adjust Fre
37. odel Use your refrigerator only as instructed in this manual These instructions are not meant to cover every possible condition and situation that may occur Common sense and caution must be practiced when installing operating and maintaining any appliance Please record your model and serial numbers below for future reference This information is found on the serial plate located inside the refrigerator compartment NOTE Use only soap and water to clean serial plate Model Number Questions 1 800 944 9044 United States 1 800 265 8352 Canada or visit our web site at www frigidaire com Serial Number Purchase Date Serial Plate Extend Your Warranty Protection With An Extended Service Contract CALL 1 800 944 9044 To Enjoy These Benefits e Total freedom from repair bills so unexpected repairs won t upset your budget e Fast convenient toll free service is just a phone call away e Top quality repairs by factory trained experts e Quick access to genuine replacement parts so you can rest assured your refrigerator is repaired with the proper components Please attach sales receipt here for future reference PLEASE COMPLETE AND MAIL IN THE PRODUCT REGISTRATION CARD INCLUDED WITH YOUR REFRIGERATOR IMPORTANT SAFETY INSTRUCTIONS a WARNING Please Read All Instructions Before Using This Refrigerator FORYOUR SAFETY e
38. of ice every 24 hours depending on usage conditions Ice is produced at a rate of 8 cubes every 75 to 90 minutes Because of new plumbing connections the first production of ice cubes may be discolored or have an odd flavor These should be discarded until the cubes made are free of discoloration and taste ICE AND WATER DISPENSER FEATURES The ice and water dispenser conveniently dispenses chilled water and ice cubes or crushed ice depending on the model To operate the ice dispenser select the ice option desired using the touchpad Press a glass against the dispensing paddle as far up as possible to catch all ice To stop dispensing ice pull glass away from dispensing paddle Do not remove the glass until the ice has completely dispensed Complete instructions for the dispenser operation are attached to the inside of the freezer door ICE DISPENSER TIPS e Ice cubes stored too long may develop an odd flavor Empty the ice container and ensure that the wire signal arm is in its down or ON position side mounted or the ice maker s On Off power switch is turned On set to the I position rear mounted The ice maker will then produce more ice Occasionally shake the ice container to keep ice separated Keep the wire signal arm in its up or OFF position side mounted or the ice maker s On Off power switch turned Off set to the O position rear mounted until the refrigerator is connected to the water
39. oper operation of your refrigerator Installation Clearances e Allow the following clearances for ease of installation proper air circulation and plumbing and electrical connections Sides amp Top 3 8 Back 1 DOOR OPENING NOTE If you refrigerator is placed with the door hinge side against a wall you may have to allow additional space so the door can be opened wider Your refrigerator should be positioned to allow easy access to a counter when removing food For best use of drawers and freezer baskets the refrigerator should be in a position where both the refrigerator and freezer doors can be fully opened TOE GRILLE INSTALLATION REMOVAL To Install Toe Grille 1 Open freezer and fresh food compartment doors 2 Line up toe grille at base of refrigerator making sure the four bottom tabs are resting through holes at base of cabinet 3 Starting from left side of toe grille press in on first top tab using your thumb and push toe grille forward until it snaps in place Continue this process until all tabs are snapped in place and toe grille is secured to refrigerator To Remove Toe Grille 1 Open freezer and fresh food compartment doors 2 Working from left side of toe grille slip your fingers between top of toe grille and cabinet Gently pull forward until first set of tabs are free Slide your hand down past the free tabs and pull forward again until
40. or the ice to be made When ice is made the dispenser should operate Ensure freezer door is closed Motor is overloaded Motor overload protector will reset in approximately 3 minutes Ice can then be dispensed Ice dispenser is jammed Ice has melted and frozen around auger due to infrequent use temperature fluctuations and or power outages Ice cubes are jammed between ice maker and back of ice container Ice cubes are frozen together Ice cubes are hollow or smaller than normal 25 Remove ice container thaw and empty the contents Clean container wipe dry and replace in proper position When new ice is made dispenser should operate Remove ice cubes that are jamming the dispenser Use the dispenser often so that cubes do not freeze together The ice amp water filter cartridge could be clogged Replace the filter cartridge Dispensing system operates best at 30 100 psi water pressure Well water pressures should fall within this range BEFORE YOU CALL PROBLEM CAUSE CORRECTION WATER DISPENSER Dispenser will not dispense water Household water line valve is not open Freezer door is not closed Ice amp water filter cartridge is clogged Front filter not fully installed if equipped Open household water line valve See PROBLEM section ICE MAKER IS NOT MAKING ANY ICE Ensure that freezer door is closed Replace filter cartridge Push filter in unti
41. other sharp instruments which can scratch the appliance surface when removing adhesive labels Any glue left from tape or labels can be removed with a mixture of warm water and mild detergent or touch the glue residue with the sticky side of tape you have already removed Do not remove the serial plate Care amp Cleaning Chart Part Wha Touse TipsandPrecautions Interior Door Use 2 tablespoons of baking soda in 1 quart of warm water Be sure to wring Liner excess water out of sponge or cloth before cleaning around controls light bulb or any electrical part Door Gaskets e Soap and water Wipe gaskets with a clean soft cloth Drawers Bins e Soap and water Do not wash any removable items bins drawers etc in dishwasher Glass Shelves Soap and water Allow glass to warm to room temperature before immersing in warm water Glass cleaner Mild liquid sprays Toe Grille Soap and water Vacuum dust from front of toe grille Remove toe grille See illustration on e Soap and water e Baking soda and water Mild liquid sprays page 4 Vacuum backside and wipe with sudsy cloth or sponge Rinse and Vacuum attachment dry Exterior and Soap and water Do not use commercial household cleaners ammonia or alcohol to clean Handles Non Abrasive Glass handles Use a soft cloth to clean smooth handles Do Not use a dry cloth to Cleaner clean smooth doors seg and jena water IAO Never use CHLORIDE to clean stainless steel andles Stainless Steel Cl
42. ow are descriptions of some of the most common sounds you may hear and what is causing them You may hear air being forced through the refrigerator by the evaporator fan C Defrost Heater During defrost cycles water dripping onto the defrost heater may cause a hissing or sizzling sound After defrosting a popping sound may occur NOTE Rigid foam insulation is very energy efficient but is not a sound insulator IMPORTANT During the automatic defrost cycle you may notice a red glow in the vents on the back wall of your freezer compartment This is normal during the defrost cycle D Automatic Ice Maker If your refrigerator is equipped with an automatic ice maker you will hear ice cubes falling into the ice bin E Cold Control amp Automatic Defrost Control These parts can produce a snapping or clicking sound when turning the refrigerator on and off F Condenser Fan You may hear air being forced through the condenser by the condenser fan G Compressor Modern high efficiency compressors operate much faster than older models The compressor may have a high pitched hum or pulsating sound H Water Valve If your refrigerator is equipped with an automatic ice maker you will hear a buzzing sound as the water valve opens to fill the ice maker during each cycle IMPORTANT Your ice maker is turned On at the factory so it can work as soon as you install your refrigerator To ensure proper function of your
43. owel or dish cloth handy to wipe up any water that may drip out of the filter or housing Two small holes near the back of the housing have been added for any excess water to escape It would be best to clear away any food near this area on the top shelf in advance of removing the filter 3 Pull the old filter cartridge straight out of the housing 4 Discard the old filter 5 Remove the new filter cartridge from the packaging and insert into the filter housing the same way the old one came out 6 When the cartridge is almost in you will feel it stop against the clip assembly in the back of the housing The clip assembly holds the filter cartridge firmly in place At this point you will need to push firmly until the cartridge snaps fully in place When completely in place the front of the filter cartridge will be flush with the front of the housing 7 Set ice maker wire signal arm to the ON down position side mounted or the ice maker s On Off power switch is turned On set to the 1 position rear mounted 8 Fill a glass with water As you are doing this check for leaks at the filter housing There will be noticable spurts and sputters as the system pushes the air out through the system and out the dispenser nozzle This is normal 9 After you have run one glass of water continue to flush the system for approximately 3 minutes to assure that the purest water possible is stored in the water storage tank I
44. purchase Costs of service calls that are listed under NORMAL RESPONSIBILITIES OF THE Pay all costs for repairing or replacing any parts of this appliance which prove to be defective in materials or date workmanship Excludes original and replacement Ice amp Water CONSUMER filter cartridges if equipped Original and replacement cartridges are warranted for 30 days parts only LIMITED 2 d_ 5TH Second through fifth Repair or replace any parts in the cabinet liner or sealed Costs for pickup and delivery of the appliance YEAR WARRANTY years from original refrigeration system compressor condenser evaporator required because of service Costs for labor parts Cabinet Liner and purchase date dryer or tubing which prove to be defective in materials or and transportation other than with respect to the Sealed System workmanship cabinet liner or Sealed Refrigeration System LIMITED Time periods listed All of the provisions of the full warranties above and the Costs of the technician s travel to the home and any WARRANTY above exclusions listed below apply costs for pick up and delivery of the appliance Applicable to the required because of service State of Alaska In the U S A and Puerto Rico your appl Inc In Canada your iance is warranted by Electrolux Major Appliances North America a division of Electrolux Home Products appliance is warranted by Electrolux Major Appliances North America a
45. realign doors when they are replaced 3 Remove top hinge and lift refrigerator door off bottom hinge pin Set door aside 4 Remove bottom hinge if necessary 5 Reverse this procedure to reinstall refrigerator door To Remove Freezer Door 1 Disconnect water line coming from lower hinge of freezer door at connection located under front of freezer Press outer ring against face of fitting then pull to remove tube 2 Remove top hinge cover screw on freezer door and remove cover 3 Disconnect wiring harness connector plug at top hinge place your thumbs on flat sides of each connector and bend both parts back and forth then with firm grasp pull both pieces apart 4 Trace around hinge with soft lead pencil This will make it easier to realign doors when they are replaced 5 Remove top hinge allowing wiring harness to pull through hinge and lift freezer door off of bottom hinge pin Lay door down flat to avoid kinking water line 6 Remove bottom hinge if necessary 7 Reverse this procedure to reinstall freezer door When both doors have been reinstalled connect water line by inserting tube and push until mark touches face of fitting replace toe grille and plug in electrical power cord Turn both temperature controls to center position Adjust settings as necessary Line Tubing Hinge Assembly Screws FEATURES AT A GLANCE Freezer and Refrigerator Controls Features may vary according to model Ice Crea
46. sh Food control one degree warmer by pressing the Up Cold button Adjust Freezer control one degree colder by pressing Down Colder button Adjust Freezer control one degree warmer by pressing the Up Cold button TEMPERATURE CONTROLS SYSTEM MONITORING ALARMS The electronic control system continuously monitors your refrigerator freezer for temperature consistency and doors left ajar Variances from normal operating conditions are r GALLERY communicated by audible tones and a set of two status indicator lights DoorAjar A Green OK RESPONDING TO ALARMS AUDIBLE TONES amp Filter nga INDICATOR LIGHTS Seton Your refrigerator s control system can convey the following information through audible tones and the alarm indicator lights Door Flashing Freezer or Fresh Food Close door to silence and reset alarm Ajar Green door has been open for over five minutes AIR FILTER INDICATOR amp STATUS LIGHTS Your refrigerator s fresh food air filter needs to be replaced from time to time You can monitor the need for replacement by referring to the status light while the air filter is ON To turn on the air filter press the Air Filter button To turn off the air filter press the Air Filter button To RESET the air filter press the Air Filter button and hold for 3 seconds Air Filter Status Light not available on all models Yellow Air filter is about 80 percent use
47. shelf forward Shelves can be extended as far as the stopper will allow but are not removable from their mounting brackets x Cantilever Glass Shelf DOOR STORAGE Cantilever Sliding Glass Shelf Door bins and shelves are provided for convenient storage of jars bottles and cans Frequently used items can be quickly selected Some models have door bins that can accommodate gallon sized plastic drink containers and economy sized jars and containers Some bins are adjustable for maximum storage capacity The dairy compartment which is warmer than the general food storage section is intended for short term storage of cheese spreads or butter Fixed Door Bin LOOKING INSIDE CONTINUED TALL BOTTLE RETAINER SOME MODELS SPECIAL ITEM RACK The Tall Bottle Retainer keeps tall containers in the bin from SOME MODELS falling forward when opening or closing the refrigerator door The innovative design of To install hold the retainer at the top and slide it over the the Special Item Rack outside wall of the bin as shown in the diagram The Tall allows you to store a six Bottle Retainer works best with a Bin Snugger pack of 12 ounce drink cans a bottle of wine a two liter soft drink bottle or a carton of eggs The Special Item Rack mounts on the left side of your refrigerator To install just slide the Special Item Rack onto any shelf as shown in the drawing CRIS
48. supply or whenever the water supply is turned off IMPORTANT Your ice maker is shipped with the wire signal arm in the ON position side mounted or turned ON rear mounted at the factory To ensure proper function of your ice maker hook up water supply immediately or turn ice maker OFF by lifting the wire signal arm until it clicks and locks in the UP position side mounted or turn the On Off switch to the Off O position If the icemaker is not turned off and the water supply is not connected the water valve will make a loud chattering noise AUTOMATIC ICE AND WATER DISPENSER a CAUTION If the dispensing paddle is pushed for more than 4 minutes the dispenser motor may overload and stop The overload protector will reset automatically after 3 or 4 minutes e Ifa large quantity of ice is needed at one time it is best to remove cubes directly from the ice container e The following sounds are normal when the ice maker is operating e Motor running e Ice dropping into ice container e Water valve opening or closing e Ice loosening from tray e Running water e Stop the ice maker when cleaning the freezer and during vacations e Ifthe ice maker will be turned off for a long period of time turn the water supply valve to the closed position CLEANING THE ICE DISPENSER Clean the dispenser and ice container at regular intervals particularly before you take a vacation or move or if the ice dispenser sticks 1
49. ter cartridge should come down with cup If cartridge remains in housing pull down gently while twisting filter back and forth 4 Rinse out cup under running water in the upper right back corner of the fresh food 5 compartment The large o ring that seals the filter system sets in the o ring groove down inside the cup Should the o ring fall out during filter cartridge replacement simply place it back in the groove prior to screwing the cup back in place If the o ring becomes 4 damaged you will need to order one from the Consumer dealer where you bought 5 ee Assistance Center the refrigerator contact WN ae Discard old filter cartridge Order new filter cartridges through the gt the Consumer J 7 Assistance Center at 1 iS ee SS G l 800 944 9044 or go to Remove new filter cartridge from packaging Place in cup The Small O ring aq 8 end with the small o ring should be up out of the cup o r website at T EAA a eo n 7 Not Use Wrench www frigidaire com It Filter Cartridge ie lo einstall Cup Fi er cartridge will self align as cup is SS tightened Be sure cup is completely tightened with might be good to order Lit a some filter cartridges Large Oring PureSource logo facing outward Do Not Tighten Past Stop when you first install your Filter Cup 7 U 9 Set ice maker wire signal arm to the ON down position side refrigerator Be sure to KI mounted or the ice maker
50. the Touch Pad Press glass against ICE dispensing paddle as far up as possible to catch all ice LIGHT Press the LIGHT Touch Pad to turn on dispenser light Press again to turn the light off The light also turns on automatically when ice and or water is dispensed Replace light bulb with an appliance bulb of the same wattage FILTER The FILTER STATUS indicator light above the Touch Pad QO will light up each time the dispenser STATUS is used The following filter light indications are Green The filter is still operating within its specified life cycle Amber The filter has reached approximately 80 of its useful life This is the recommended time to purchase a replacement filter Red The filter is 100 used up Change the filter as soon as possible After the filter cartridge has been changed press and hold the FILTER RESET Touch Pad 6 for 10 15 seconds NOTE The Green Red and Amber lights will flash when reset is completed LOCK The Ice amp Water Dispenser can be locked out to prevent unwanted use To Lock Out Press the LOCK Touch Pad Q for 3 5 seconds A Red light will appear above the Touch Pad To Unlock Press the LOCK Touch Pad Q for 3 5 seconds until the Red light above the Touch Pad goes out WATER To operate the water dispenser press a glass against the WATER dispensing paddle lt TO stop dispensing water pull the glass away from the dispensing paddle Dispensed water is not cold For colder water add crushed ice or c
51. the temperature control panel will disable your refrigerators cooling system but does not disconnect the power to the light bulb and other electrical components To turn off power to your refrigerator you must unplug the power cord from the wall outlet Grounding type wall receptacle Do not under any circumstances cut remove or bypass the grounding prong 3 prong grounded plug Power cord with INSTALLATION This Owner s Guide provides specific operating instructions for your model Use the refrigerator only as instructed in this Use amp Care Manual Before starting the refrigerator follow these important first steps LOCATION e Choose a place that is near a grounded electrical outlet Do Not use an extension cord or an adapter plug e f possible place the refrigerator out of direct sunlight and away from the range dishwasher or other heat sources e The refrigerator must be installed on a floor that is level and strong enough to support a fully loaded refrigerator e Consider water supply availability for models equipped with an automatic ice maker INSTALLATION a CAUTION Do Not install the refrigerator where the temperature will drop below 55 F 13 C or rise above 110 F 43 C The compressor will not be able to maintain proper temperatures inside the refrigerator Do Not block the toe grille on the lower front of your refrigerator Sufficient air circulation is essential for the pr
52. tted Condenser is dirty It s normal for the refrigerator to work longer under these conditions It takes 8 12 hours for the refrigerator to cool down completely Ice maker operation causes refrigerator to run slightly more Warm air entering the refrigerator causes it to run more Open doors less often Ensure refrigerator is level Keep food and containers from blocking door See PROBLEM section OPENING CLOSING OF DOORS DRAWERS Set refrigerator control to warmer setting until refrigerator temperature is satisfactory Allow 24 hours for temperature to stabilize Clean or change gasket Leaks in door seal will cause refrigerator to run longer in order to maintain desired temperatures Clean condenser See Care amp Cleaning Chart in Care and Cleaning section Compressor goes off and on frequently Thermostat keeps the refrigerator at a constant temperature TEMPERATURES ARE TOO COLD This is normal Refrigerator goes on and off to keep temperature constant Freezer temperature too cold Refrigerator temperature is satisfactory Refrigerator temperature too cold Freezer temperature is satisfactory Food stored in drawers freezes Freezer control is set too cold Refrigerator control is set too cold Refrigerator control is set too cold Set freezer control to a warmer setting Allow 24 hours for temperature to stabilize Set refrigerator control to a warmer setting Allow 24 hours for temp
53. ty unless the water has been adequately disinfected before or after traveling through the filtration system e Rated Capacity 400 gallons e Rated service flow 5 GPM e Maximum Rated Pressure 100 PSI e Maximum Operating Temp 100 F Changing the Filter Water conditions vary throughout the world but changing the water filter every 6 9 months normally will ensure the highest possible water quality The Filter Status light will turn red after approximately 400 gallons of water has flowed through the ice and water dispenser Also if the filter has been in a refrigerator that has not been in use for awhile during moving for example change the filter before reinstalling the refrigerator The dispenser system will also operate without filtration with filter cartridge removed and bypass installed To change filter It is not necessary to turn the water supply off to change the filter 1 Set ice maker wire signal arm to the OFF up position side mounted or the ice maker s On Off power switch turned Off set to the O position rear mounted 2 Push the Filter Release Button located to the right of the filter cartridge to release the filter from the housing To minimize the possibility of the filter falling out of the housing during removal it would be best to hold the filter as it moves out toward you NOTE A small amount of water may be released during this operation You should have a paper t
54. ubes before dispensing water A drip tray located at the base of the dispenser catches small spills and allows them to evaporate This drip tray is removable and dishwasher safe Do not pour water and excess ice in this area because there is no drain 12 AUTOMATIC ICE AND WATER DISPENSER HOW THE WATER DISPENSER WORKS The water tank located behind the drawers in the refrigerator compartment automatically fills as water is dispensed For proper dispenser operation the recommended supply water pressure should fall between 30 psi and 100 psi After the refrigerator is connected to the water supply fill the water tank by drawing one glass of water It may take about 1 minutes after activating the dispenser paddle before water begins to fill this first glass Continue flushing the system for 3 minutes to rid the tank and plumbing connections of any impurities The water dispenser has a built in shutoff device that will stop the water flow after 3 minutes of continuous use Simply release the dispenser paddle to reset the shutoff mechanism ZN cauTION Water pressure must not exceed 100 Ibs Excessive pressure may cause water filter to malfunction Chemicals from a malfunctioning softener can damage the ice maker If the ice maker is connected to soft water ensure that the softener is maintained and working properly HOW THE ICE DISPENSER WORKS SIDE MOUNTED The ice maker and container are located in the top of the fre
55. ubes will freeze together in the bin and jam the dispenser mechanism Remove the ice storage bin and shake to loosen the cubes ZN cauTION NEVER use an ice pick or similar sharp instrument to break up the ice This could damage the ice storage bin and dispenser mechanism AUTOMATIC ICE AND WATER DISPENSER PURESOURCE ICE AND WATER FILTER SOME The dispenser system will also operate without filtration with MODELS filter cartridge removed System Startup To change filter Water supply does not need to be turned off however do not It is not necessary to turn the water supply off to change the filter use ice and water dispenser while installing filter The filter 1 Open freezer door and leave open until filter change is cartridge has already been installed in the filter housing at the factory Refer to the How The Water Dispenser Works section to properly fill the system with water complete 2 Set ice maker wire signal arm to the OFF up position side mounted or the ice maker s On Off power switch turned Off set NOTE If you purchased a refrigerator with a PureSource Ice and Water filter please read the following use and care information This ice and water filter system filters water to your ice maker and water dispenser It is located to the O position rear mounted 3 Hold filter cup firmly and unscrew towards left Some water could leak out as you remove cup This is normal Fil
56. ving Tips Leave refrigerator operating during vacations of 3 weeks or less Short Use all perishable items from refrigerator compartment Vacations Turn automatic ice maker off and empty ice bucket even if you will only be gone for a few days Remove all food and ice if you will be gone one month or more Turn off automatic ice maker and turn water supply valve to closed position The On Off button on the Electronic Control only controls your refrigerator s cooling Long system To turn off power to your refrigerator you must unplug the power cord from the Vacations wall outlet Clean interior thoroughly Leave both doors open to prevent odors and mold build up Block doors open if necessary Remove all food and ice If using handcart load from side Adjust rollers all the way up to protect them during sliding or moving Pad cabinet to avoid scratching surface IMPORTANT If the refrigerator is going to be stored or moved in freezing temperatures the water in the ice and water system must be drained completely Failure to do so could result in water leaks when the refrigerator is put back into service Contact a service representative to perform this operation 21 WARRANTY INFORMATION REFRIGERATOR WARRANTY Your refrigerator is protected by this warranty WARRANTY PERIOD THE CONSUMER WILL BE RESPONSIBLE FOR THROUGH OUR AUTHORIZED SERVICERS WE WILL FULL ONE YEAR WARRANTY One year from original
Download Pdf Manuals
Related Search