Frigidaire FFTA0833Q1 Installation Instructions
Contents
1. A mi nil Va 1 8 Hole Grille amp Flange Installation Instructions FINISHING INSTALLATION 1 Install the 1 x 1 x 84 long stuffer seal between the wall sleeve and the unit A flat bladed screwdriver or putty knife is recommended 2 Assemble the trim frame by inserting top and bottom pieces into side pieces and snapping into place 3 Pull cord through trim frame then slide over unit until flush with wall NOTE For larger sleeves an accessory trim kit is available EA120T 142. Installation Instructions Wall Sleeve Brands 2 Fedders 19 3 4 Deep 1 Remove existing rear grille as shown on Page 3 of this manual and replace with provided louvered rear panel Install as shown here NOTE You may need to drill holes in flange of existing sleeve to match new rear grille 2 Attach 2 4 x 3 x 1 centering support blocks one on each side wall Place in center of side wall with the tapered end facing the 80 4 5 Rear Louvers 4 Top View X ye opening wo Cut 2 17 Tapered Spacer Blocks as shown below into two pieces a p y 4 3 4 Tapered Spacer Block Paf i ra t 1 Mi Here protection Paper Backing j 4 The 4 section is placed in front of the rib on base with the tapered end facing the back of the sleeve The remaining portion will be placed behind the rib again sloping toward the rear of the sleeve This helps induce a rearward slope on the unit 5 Attach 1 1 x 3 8 x 25 long seal in the center at the top of the sleeve Remove the backing paper and press into position 6 Attach 2 1 x 3 8 x 14 seals to the left and right sides of the sleeve 7 Cut 2 1 x 3 8 x 25 long seals to 14 long each and attach to the vertical sections of the grille as shown 8 Gently slide unit into sleeve 9 Before sliding all the way back remove 2nd screw from front on left side of unit 10 Remove the plastic washer
3. Installation Instructions Wall Sleeve Brands 6 Whirlpool 17 1 8 Deep 1 Remove existing rear grille as shown on Page 3 of this manual and replace with provided louvered rear panel Install as shown here NOTE You may need to drill holes in flange of existing sleeve to match new rear grille 2 Cut 2 17 Tapered Spacer Blocks as shown below into two pieces eee l 3 4 Tapered Spacer Block 1 to l Fe Cut Here protection Paper Backing w slope on the unit 4 Attach 1 1 x 3 8 x 25 long seal in the center at the top of the sleeve Remove the backing paper and press into position 5 Attach 2 1 x 3 8 x 14 seals to the left and right sides of the sleeve 6 Cut 2 1 x 3 8 x 25 long seals to 14 long each and attach to the vertical sections of the grille as shown 7 Center unit amp gently slide unit into sleeve 8 Before sliding all the way back remove 2nd screw from front on left side of unit 9 Remove the plastic washer from the screw 4 80 Ml 5 Rear Louvers a 80 t Top View Install to the floor of the sleeve as shown This helps induce a rearward 10 Screw and attach the other end of the ground wire from sleeve to the unit as shown in picture Make sure that the toothed washer is against the cabinet 11 Slide the unit completely to the rear to ensure a good seal making sure the ground wire does n
4. Conditioner must be in sound structural condition and have a rear grille that securely attaches to sleeve or rear flange that serves as a stop for the Air Conditioner e For new installations a Frigidaire Sleeve Kit EA108T is recommended amp CAUTION e When installation is complete replacement unit MUST have a rearward slope as shown in Fig 1 2 Remove old Air Conditioner from wall sleeve and prepare wall sleeve as follows Clean interior do not disturb seals Wall sleeve must be securely fastened in wall before installing Air Conditioner Drive more nails or screws through sleeve into wall if needed Retouch wall sleeve painted surface if needed 3 If not existing drill a 3 16 clearance hole for grounding screw through left side of wall sleeve in a clear area about 3 inches maximum back from front edge of sleeve using grounding screw and toothed washer Pull loose end of ground wire out front of sleeve and temporarily bend it down and around lower edge of sleeve Fig 2 This ground wire will later be attached to frame of air conditioner once it is installed Wall 1 4 to 5 16 al sleeve gt lt 4 3 16 al Wall sleeve to unit 16 sleeve grounding Hole UNIT BEAR o FRONT 1 o LEVEL Fig 1 Fig 2 Installation Instructions 4 Prepare the wall sleeve for installation of the new unit per the following Brand instructions 1 Emerson 15 Deep 2 Fedders 19 Deep 3 Fedders
5. Installation Instructions Wall Sleeve Brands 1 Emerson 15 Deep 1 Remove existing rear grille as shown on Page 3 of this manual and replace with provided louvered rear panel Install as shown here NOTE You may need to drill holes in flange of existing sleeve to match new rear grille 2 Attach 1 1 x 3 8 x 25 long seal in the center at the top of the sleeve Remove the backing paper and press into position 3 Attach 2 1 x 3 8 x 14 seals to the left and right sides of the sleeve 4 Cut 2 1 x 3 8 x 25 long seals to 14 long each and attach to the vertical sections of the grille as shown 5 Attach 2 4 x 3 x 1 centering support blocks one on each side wall Place in center of side wall with the tapered end facing the opening 6 Gently slide unit into sleeve 7 Before sliding all the way back remove 2nd screw from fron on left side of unit 8 Remove the plastic washer from the screw 9 Screw and attach the other end of the ground wire from sleeve to the unit as shown in picture Make sure that the toothed washer is against the cabinet 10 Slide the unit completely to the rear to ensure a good seal making sure the ground wire does not become tangled 11 Seal amp Frame the unit as described on the last page of these instructions 12 If you have difficulty with mounting the grill to the sleeve follow the instructions for direct mounting on Page 13 Rear Louvers Top View 4
6. as shown below into two pieces 17 PAR __ v Tapered Spacer Block 1 3 4 ease ah Cut Here ill 13 A protection Paper Backing 3 Install as shown with the tapered end 1 2 from the back of the sleeve This helps induce a rearward slope on the unit 4 Attach 1 1 x 3 8 x 25 long seal in the center at the top of the sleeve Remove the backing paper and press into position 5 Attach 2 1 x 3 8 x 14 seals to the left and right sides of the sleeve 6 Cut 2 1 x 3 8 x 25 long seals to 14 long each and attach to the vertical sections of the grille as shown 7 Center unit amp gently slide unit into sleeve 8 Before sliding all the way back remove 2nd screw from front on left side of unit 9 Remove the plastic washer from the screw 10 Screw and attach the other end of the ground wire from sleeve to the unit as shown in picture Make sure that the toothed washer is against the cabinet 11 Slide the unit completely to the rear to ensure a good seal making sure the ground wire does not become tangled 12 Seal amp Frame the unit as described on the last page of these instructions 13 If you have difficulty with mounting the grill to the sleeve follow the instructions for direct mounting on Page 13 Installation Instructions Wall Sleeve Brands 5 Sears or Carrier 51S Series 18 5 8 Deep 1 Remove existing rear grille as shown on Page 3 of this manual and replace wit
7. fins of the grill are pointed away from the unit 3 Align the top of the grille with the top of the unit The overhang on each side is equal 4 If the unit has not been pre drilled some models carefully drill 4 1 8 holes through the grille and into the side flange of the unit approximately 1 to 2 from the top and bottom as in Fig 2 3 Be careful not to drill into the copper heat exchanger coils 5 Install 4 8 self tapping screws to affix the grille to the unit 6 Insert the unit into the sleeve seal BY acer seal liad Fig 1 A Grille Screws KARR Lee
8. of this manual and Rear Louvers replace with provided louvered rear panel Install as shown here NOTE You may need to drill holes in flange of existing sleeve to match new rear grille Top View 2 Attach 1 1 x 3 8 x 25 long seal in the center at the top of the sleeve Remove the backing paper and press into position 3 Attach 2 1 x 3 8 x 14 seals to the left and right sides of the sleeve 4 Attach 1 1 x x 14 long seal vertically 3 5 from the left side of the sleeve Attach the other 1 x 3 4 x 14 long seal 3 from the right side of the sleeve 5 Center unit amp gently slide unit into sleeve 6 Before sliding all the way back remove 2nd screw from front on left side of unit 7 Remove the plastic washer from the screw 8 Screw and attach the other end of the ground wire from sleeve to the unit as shown in picture Make sure that the toothed washer is against the cabinet 9 Slide the unit completely to the rear to ensure a good seal making sure the ground wire does not become tangled 10 Seal amp Frame the unit as described on the last page of these instructions 11 If you have difficulty with mounting the grill to the sleeve follow the instructions for direct mounting on Page 13 t1 Installation Instructions Wall Sleeve Brands 9 f NOTE You may need to drill holes in flange of existing sleeve to match 80 new rear grille Because of the increased unit depth
9. Installation Instructions READ BEFORE INSTALLING UNIT For Through the Wall Air Conditioners INSTALLATION WARNINGS AND CAUTION x Carefully read the installation manual before beginning Follow each step as shown x Observe all local state and national electrical codes and by qualified licensed authorized personnel only x Pay attention to danger and safety notices To avoid risk of personal injury property damage or product damage due to the weight of this device and sharp edges that may be exposed Air conditioners covered in this manual pose an excessive weight hazard Two or more people are needed to move and install the unit Wear protective gloves whenever lifting or carrying the unit AVOID the sharp metal fins of front and rear coils To prevent injury or strain use proper lifting and carrying techniques when moving unit x Carefully inspect location where air conditioner will be installed Be sure it will support the weight of the unit overan extended period of time Handle air conditioner with care Make sure air conditioner does not fall during installation Do This First for existing sleeve Note that the air conditioner dimensions are 24 wide 14 high and 19 deep without front Install Air Conditioner according to these installation instructions to achieve the best performance Save these installation instructions for future reference amp NOTE e DO NOT USE ANY SCREWS OTHER THAN THOSE
10. SPECIFIED HERE Items in Kit You may not need all parts in the kit Discard unused parts No Hardware Qty No Hardware Qty 1 Tapered Spacer Blocks 17 Long 2 10 Trim Frame side legs 2 2 Centering Support Blocks 474 x 3 x 14 4 11 Trim Frame top amp bottom legs 2 3 Plastic Divider 4 x 4 4 x 14 2 12 Ground Wire green 1 4 Stuffer Seal 1 x 1 x 84 1 13 Toothed washer for grounding screw 2 5 seal 1 x1 x 25 3 14 Grounding Screw 1 6 seal 1 x1 x 14 2 15 Grille plastic 1 7 seal 1 x3 8 x25 3 16 Grille Aluminum 1 8 seal 1 x 3 8 x14 2 17 Nuts plastic 4 9 seal 1 x 3 4 x 14 2 18 Screw w washer 4 2020213A1639 1 Installation Instructions How to Install 1 Identify the wall sleeve brand for your installation from the chart below Brand Wall Sleeve Dimensions Width Height Depth White Westinghouse 25 15 16 17 2 or 22 Frigidaire 25 15 16 17 2 or 22 Carrier 52F Series 25 15 16 17 2 or 22 General Electric Hotpoint 26 15 15 Whirlpool 25 16 17 or 23 Fedders Emerson 27 16 16 or 19 Sears Kenmore 25 16 18 Emerson Fedders 26 15 15 Carrier 51S Series 25 16 18 Friedrich 27 16 16 For larger sleeves an adaptor trim kit EA120T is available IMPORTANT All wall sleeves used to mount the new Air
11. al over the solid vertical portion of the rear grille 10 Attach 2 4 x 3 x 1 foam blocks with the slot overlapping the seal above 1 Install the divider into the slots of the foam blocks You may need to trim the length to size 12 Repeat steps 9 11 for the other vertical shown portion of the grille as shown in the picture 1 w Attach 2 1 x 1 2 x 14 seals along the sides of the sleeve again making sure all seals are flush 14 Cut the 1 x 1 x 25 seal to fit the top of the sleeve The pieces must be fitted flush to the edge of the divider 15 Center unit amp gently slide unit into sleeve 16 Before sliding all the way back remove 2nd screw from front on left side of unit 17 Remove the plastic washer from the screw 18 Screw and attach the other end of the ground wire from sleeve to the unit as shown in picture Make sure that the toothed washer is against the cabinet 19 Slide the unit completely to the rear to ensure a good seal making sure the ground wire does not become tangled 20 Seal amp Frame the unit as described on the last page of these instructions 2 If you have difficulty with mounting the grill to the sleeve follow the instructions for direct mounting on Page 13 10 Installation Instructions Wall Sleeve Brands 8 White Westinghouse Frigidaire 16 17 1 2 Deep Carrier 52F Series 1 Remove existing rear grille as shown on Page 3
12. first try dry fitting using the method described below 2 3 Use these next steps if the unit requires extra extension into the room 8 9 10 11 12 13 14 15 16 17 18 19 20 Attach 1 1 x 1 x 15 seal to the left and right sides of the sleeve Cut 1 1 x 1 x 25 long seal to 14 long and attach it vertically to Attach 1 1 x 1 x 25 long seal in the center at the top of the White Westinghouse or Frigidaire 22 Deep Remove existing rear grille as shown on Page 3 of this manual and Rear Louvers replace with provided louvered rear panel Install as shown here 4 5 x 4 y 8 Q G nae Top View Place 2 1 x 1 x 14 seals against each side Gently slide unit in and check if amount extending from the sleeve is sufficient once the trim frame is attached If position is okay remove unit and Proceed to the next step If not go to step 8 the rear grill 3 5 from the left side Repeat and attach 3 from the right side sleeve Remove the backing paper and press into position Proceed to step 14 Attach 1 x x 14 long seal over the solid vertical portion of the rear grille Attach 2 4 x 3 x 1 foam blocks with the slot overlapping the seal above Install the divider into the slots of the foam blocks You may need to trim the length to size Repeat steps 8 10 for the other vertical shown portion of the grille as s
13. from the screw 1 Screw and attach the other end of the ground wire from sleeve to the unit as shown in picture Make sure that the toothed washer is against the cabinet 12 Slide the unit completely to the rear to ensure a good seal making sure the ground wire does not become tangled 13 Seal amp Frame the unit as described on the last page of these instructions 14 If you have difficulty with mounting the grill to the sleeve follow the instructions for direct mounting on Page 13 Installation Instructions Wall Sleeve Brands 3 Fedders or Friedrich 16 3 4 Deep 1 Remove existing rear grille as shown on Page 3 of this manual and Rear Louvers replace with provided louvered rear panel Install as shown here 45 a 4 NOTE You may need to drill holes in flange of existing sleeve to match 80 80 new rear grille Top View 2 Attach 2 4 x 3 x 1 centering support blocks one on each side wall Place in center of side wall with the tapered end facing the opening 3 Cut 2 17 Tapered Spacer Blocks as shown below into two pieces pis 4 4 t protection Paper Backing se 3 4 Tapered Spacer Block t Cut Here 12 1 2 4 The 2 section is placed in front of the rib on base with the tapered end facing the back of the sleeve Cut the remaining portion to 124 and place behind the rib again sloping toward the rear of the sleeve Th
14. h provided louvered rear panel Install as shown here NOTE You may need to drill holes in flange of existing sleeve to match new rear grille A 4 80 Sine 5 Rear Louvers 4 y Top View 2 Install 2 tapered spacer blocks to the floor of the sleeve as shown This helps induce a rearward slope on the unit 3 Install as shown with the tapered end 1 2 from the back of the sleeve This helps induce a rearward slope on the unit 4 Attach 1 1 x 3 8 x 25 long seal in the center at the top of the sleeve Remove the backing paper and press into position 5 Attach 2 1 x 3 8 x 14 seals to the left and right sides of the sleeve 6 Cut 2 1 x 3 8 x 25 long seals to 14 long each and attach to the vertical sections of the grille as shown 7 Center unit amp gently slide unit into sleeve 8 Before sliding all the way back remove 2nd screw from front on left side of unit 9 Remove the plastic washer from the screw 10 Screw and attach the other end of the ground wire from sleeve to the unit as shown in picture Make sure that the toothed washer is against the cabinet 11 Slide the unit completely to the rear to ensure a good seal making sure the ground wire does not become tangled 12 Seal amp Frame the unit as described on the last page of these instructions 13 If you have difficulty with mounting the grill to the sleeve follow the instructions for direct mounting on Page 13
15. hown in the picture Attach 2 1 x 1 x 14 seals along the sides of the sleeve again making sure all seals are flush Cut the 1 x 1 x 25 seal to fit the top of the sleeve The pieces must be fitted flush to the edge of the divider Center unit amp gently slide unit into sleeve Before sliding all the way back remove 2nd screw from front on left side of unit Remove the plastic washer from the screw Screw and attach the other end of the ground wire from sleeve to the unit as shown in picture Make sure that the toothed washer is against the cabinet Slide the unit completely to the rear to ensure a good seal making sure the ground wire does not become tangled Seal amp Frame the unit as described on the last page of these instructions If you have difficulty with mounting the grill to the sleeve follow the instructions for direct mounting on Page 13 12 Installation Instructions Direct Unit Mounting The previous directions are the preferable way to mount the new rear grill The unit s performance is slightly better and the possibility of draughts is reduced As a last resort direct mounting of the grille to the unit can be considered Note The grille must be installed prior to inserting the unit into the sleeve 1 Attach the 2 seal pieces 1 X3 8 X14 as shown in Fig 1 2 Position the grille over the rear of the unit making sure that a The double set of screw holes are at the bottom b The
16. is helps induce a rearward slope on the unit 5 Attach 1 1 x 3 8 x 25 long seal in the center at the top of the sleeve Remove the backing paper and press into position 6 Attach 2 1 x 3 8 x 14 seals to the left and right sides of the sleeve 7 Cut 2 1 x 3 8 x 25 long seals to 14 long each and attach to the vertical sections of the grille as shown 8 Gently slide unit into sleeve 9 Before sliding all the way back remove 2nd screw from front on left side of unit 10 Remove the plastic washer from the screw 11 Screw and attach the other end of the ground wire from sleeve to the unit as shown in picture Make sure that the toothed washer is against the cabinet 12 Slide the unit completely to the rear to ensure a good seal making sure the ground wire does not become tangled 13 Seal amp Frame the unit as described on the last page of these instructions 14 If you have difficulty with mounting the grill to the sleeve follow the instructions for direct mounting on Page 13 6 Installation Instructions Wall Sleeve Brands 4 General Electric Hotpoint 16 7 8 Deep 1 Remove existing rear grille as shown on Page 3 of this manual and replace with provided louvered rear panel Install as shown here NOTE You may need to drill holes in flange of existing sleeve to match new rear grille Rear Louvers 4 5 a y 80 Top View gt 2 Cut 2 17 Tapered Spacer Blocks
17. or Friedrich 16 Deep 4 General Electric Hotpoint 16 Deep 5 Sears or Carrier 51S Series 18 Deep 6 Whirlpool 17 Deep 7 Whirlpool 23 Deep 8 White Westinghouse Frigidaire 16 17 Deep Carrier 52F Series 9 White Westinghouse Frigidaire 22 Deep 5 Identify your wall sleeve type and follow the instructions for that type in the following pages IMPORTANT e This unit s increased performance characteristics result from having two rear air intakes e It is very important that these installation instructions are followed so your unit can operate at maximum efficiency If there is an existing sleeve and there is an existing rear grille it needs to be replaced by one that has been shipped with the unit in the accessory kit FOR INCREASED EFFICIENCY UTILIZE THE PROVIDED LOUVERED REAR PANEL Installation of new grille provided with unit Remove the existing grille Place the grille included with the new air conditioner towards the rear of the sleeve Mark through the hole positions Drill through the sleeve flanges with a 1 8 drill bit Attach the new grille with self threading screws and washers not included Itis VERY IMPORTANT that the grille is placed exactly as shown Most decorative exterior grilles may be left in place as long as the proper interior air direction grille is installed NOTE If the provided grill is not used it may lead to product damage and possible failure NOOR WN
18. ot become tangled 12 Seal amp Frame the unit as described on the last page of these instructions 13 If you have difficulty with mounting the grill to the sleeve follow the instructions for direct mounting on Page 13 Installation Instructions Wall Sleeve Brands 7 Whirlpool 23 Deep 1 Remove existing rear grille as shown on Page 3 of this manual and replace with provided louvered rear panel Install as shown here 4 5 NOTE You may need to drill holes in flange of existing sleeve to match E new rear grille Because of the increased unit depth first try dry fitting using the method described below 2 Place 2 1 x 1 2 x 14 seals against each side 3 Gently slide unit in and check if amount extending from the sleeve is sufficient once the trim frame is attached Rear Louvers Top View 4 4 If position is okay remove unit and Proceed to the next step If not go to step 9 5 Attach 1 1 x 1 x 25 long seal in the center at the top of the sleeve Remove the backing paper and press into position 6 Attach 2 1 x 1 x 14 seals to the left and right sides of the sleeve 7 Cut 2 1 x 3 8 x 25 long seal to 14 long each and attach to the vertical sections of the grille as shown 8 Attach the tapered spacer blocks to the floor of the sleeve Now go to step 15 Use these next steps if the unit requires extra extension into the room 9 Attach 1 x x 14 long se
Download Pdf Manuals
Related Search