Frigidaire FFRA0511Q1 Installation Instructions
Contents
1. into the room A Hold the side Panel in one hand and gently pull back the center to free the open end See FIG 1 B Slide the free end T section of the panel directly into the cabinet as shown in FIG 2 Slide the panel down Be sure to leave enough space to slip the top and bottom of the frame into the rails on the cabinet C Once the panel has been installed on the side of the cabinet make sure it sits securely inside the frame channel by making slight adjustments Slide the top and bottom ends of the frame into the top and bottom rails of the cabinet See FIG 3 ay D Slide the panel all the way in and repeat on the other side FIG 1 FIG 2 T section FIG 3 Top Rail n L NF Wi AE I Hit iy WW 4 Hah Hl LL il gt Bottom Rail Your air conditioner is designed to install in standard double hung windows with opening widths of 23 to 36 inches 584 mm to 914 mm FIG 4A FIG 4B Lower sash must open sufficiently to allow a clear vertical opening of 13 inches 330 mm Side louvers and the rear of the air conditioner must have clear air space to allow enough airflow through the condenser for heat removal The rear of the unit must be outdoors not inside a building or garage Fig 4B EXTERIOR WALL 23 to 36 584 mm to 914mm INTERIOR WALL Wooden Windows Vinyl Clad W2. Bottom Rail Hi ae Rail Wooden Window Vinyl Clad Window INSIDE See j OUTSIDE about 1 4 1 2 peel off the protective backing and plug any gaps if needed as shown FIG 13 Turn the air conditioner off and disconnect power cord Remove sash seal from between windows and unscrew sash lock Remove screws installed through frame and framelock Close slide side panels into frame Keeping a firm grip on air conditioner raise sash and carefully remove Be careful not to spill any condensate water while lifting unit from window Store parts WITH air conditioner 4
3. ED HERE e FOR SAFETY REASONS THE TOP RAIL MUST BE SECURELY FASTENED WITH ALL FOUR 4 sash lock 1 SCREWS weather seals 5 6 X3 4 X1 12 5 window sash seal foam 1 Some assembly is required Please read these instructions carefully Top Rail Hardware Qty TOOLS NEEDED 3 8 Screw 4 e Philips Screwdriver Top Rail 1 e Drill If pilot holes are needed Before installing the top rail must be assembled on the unit A Remove the air conditioner from the carton and place on a flat surface B Remove top rail from the rear of the packaging material as shown in Fig A C Align the hole in the top rail with those on the top of the unit as shown in Fig B D Secure the top rail to the unit with the 3 8 Screws as shown in Fig C Top Rail W 7 SS al Packaging A 2020211A2578 1 Installation LEFT RIGHT FILLER PANEL ASSEMBLY NOTE Top Rail and Side Panels at each side are offset to provide the proper pitch to the rear of 5 16 This is necessary for proper condensed water utilization and drainage If you are not using the Side Panels for any reason this pitch to the rear must be maintained Place unit on floor a bench or a table There is a Left and Right side Filler Panels be sure to use the proper al panel for each side When installed the flange for securing the panel in place to the window sill will be facing
4. Installation Instructions READ BEFORE INSTALLING UNIT OPP Window Mounting 5 000 6 500 BTU INSTALLATION WARNINGS AND CAUTION Carefully read the installation manual before beginning Follow each step as shown Observe all local state and national electrical codes and by qualified licensed authorized personnel only Pay attention to danger and safety notices To avoid risk of personal injury property damage or product damage due to the weight of this device and sharp edges that may be exposed Air conditioners covered in this manual pose an excessive weight hazard Two or more people are needed to move and install the unit Wear protective gloves whenever lifting or carrying the unit AVOID the sharp metal fins of front and rear coils To prevent injury or strain use proper lifting and carrying techniques when moving unit Carefully inspect location where air conditioner will be installed Be sure it will support the weight of the unit overan extended period of time Handle air conditioner with care Make sure air conditioner does not fall during installation A NOTE Mounting Hardware Qty I gt 1 2 screws J e SAVE CARTON and these INSTALLATION z INSTRUCTIONS for future reference The carton is ME lock frame 2 the best way to store unit during winter or when not You 3 For Wooden windows in use lock frame 2 e DO NOT USE ANY SCREWS OTHER THAN For Vinyl Clad windows THOSE SPECIFI
5. indows 2 Storm Window If the air conditoner is blocked by Storm Window add wood as Board shown in FIG 5 or remove storm window before air conditioner Storm window 1 1 2 min thickness as is installed frame or other 38 mm required for If Storm Window Frame must remain be sure the drain holes or obstruction proper pitch to slots are not caulked or painted shut Accumulated Rain Water lt y rear along or Condensation must be allowed to drain out L aa entire sill Fasten with nails or screws 2 Installation 3 Keep a firm grip on the air conditioner carefully place the unit into the window opening so the bottom of the air conditioner frame is against the window sill FIG 6A amp FIG 6B Carefully close the window behind the top rail of the unit FIG 6B FIG 6A INSIDE OUTSIDE INSIDE OUTSIDE Wooden Windows Vinyl Clad Windows Extend the side panels out against the window frame FIG 7A for wooden windows FIG 7B for Vinyl Clad windows FIG 7A FIG 7B aay window frame SS windows FIG 8B for Vinyl Clad windows FIG 8A FIG 8B 5 Place the frame lock between the frame extensions and the window sill as shown FIG 8A for wooden wooden windows Vinyl Clad windows O Drive locking screws A For wooden windows Drive 1 2 12 7 mm locking screws thr
6. ough the frame lock and into the sill FIG 9A NOTE To prevent window sill from splitting drill 1 8 3mm pilot holes before driving screws Drive 1 2 12 7 mm locking screws through frame holes into window sash FIG 9B B For Vinyl Clad windows Drive 1 2 12 7 mm locking screws through the frame lock and into the window sash FIG 9B NOTE Before driving the screws use a drill to drill 5 holes through the holes in the frame lock and frame extensions into the windows sash as shown FIG 9B FIG 9A cS Sas Installation NOTE It is difficult to lock the windows with the sash lock for Vinyl Clad windows so you can use lock by To secure lower sash in place attach right angle sash lock with 1 2 12 7mm screw as shown FIG 10 window itself 8 Cut foam window seal and insert it into the space between the upper and lower sashes FIG 11 FIG 10 FIG 11 FOAM SEAL O Check that air conditioner is tilted back about 1 4 to 1 2 tilted about 2 to 4 downward to the outside see 10 Trim the weather seal 6 X3 4 X1 12 with a proper length Removing the air conditioner From Window FIG 12A amp FIG 12B After proper installation condensate should not drain from the overflow drain hole during normal use correct the slope otherwise FIG 12A FIG 12B INSIDE H H1 H2 about 1 4 1 2 4 i as a H
Download Pdf Manuals
Related Search