Frigidaire FFPA1222R1 Owner's Manual
Contents
1. V buttons together for 3 seconds There is a 2 Second delay for the compressor shutting down when selecting FAN ONLY HEAT This is to cover the possibility of having to roll through to select another mode After a power outage the unit will memorize the last setting and return the unit to the same setting once power is restored Indoor operating temperature range for this product is 62 F to 95 F 17 C to 35 C CARE amp CLEANING Filter A Fig 24 Remove three screws and take the air intake grille Remove the filter B out from the grille lt Filter B Fig 26 2009 Electrolux Home Products Inc Clean your air conditioner occasionally to keep it looking new Be sure to unplug the unit before cleaning to prevent shock or fire hazards Air Filter Cleaning This unit has two filters they are filter A and B Grasp the upper panel tab and take off the filter A which behind the grill of the back panel Fig 24 Remove the lower filter B by loosening the screws Take down the air inlet grille then remove the air filter as shown in Fig 25 amp 26 Wash the filter using liquid dishwashing detergent and warm water Rinse filter thoroughly Gently shake excess water from the filter Be sure filter is thoroughly dry before replacing Or instead of washing you may vacuum the filter clean Replace the filter after the filter is dry Cabinet Cleaning Be sure to2. 3 and screw the hose to adaptor A Fig 4 2 Extend the other side of the hose and screw it to adaptor B Fig 5 3 Slide the assembly onto unit Fig 6 4 Affix the adaptor B into the window slider kit and seal Fig 7 amp 8 Vertical window Window Slider Kit Minimum 26 6 67 5cm Maxmum 48 5 123cm Window Slider Kit Minimum 26 6 67 5cm Maxmum 48 5 123cm The hose can be extended from its original length of 15 up to 59 but it is the best to keep the length to minimum required Also make sure that the hose does not have any sharp bends or sags Fig 9 6 2009 Electrolux Home Products Inc 4 Extend the side of hose Fig 3 1D Fig 4 I es sy ZN Fig 5 Slide onto y Fig 6 All rights reserved Installation I nstructions Installation I nstructions continued Installation in a double hung sash window 1 Cut the foam seals adhesive type to the proper lengths and attach them L to the window and stool Fig 10 2 Open the window sash and place the window slider kit on the window stool Foam Seale Fig 11 Attach the window slider kit to the window stool Adjust the length badhesie De of the window slider kit according to the width of window Screw down the two screws on the window slider kit See Fig 11 Cut the adjustable window Slider kit if the width of wind
3. be used 1 Press the MODE button until the Cool indicator lights 2 Press the V A Temp buttons for desired setting 3 Press the FAN button for desired fan speed In this mode you do not need to use the exhaust adaptor hose 1 Press the MODE button until the Heat indicator lights 2 Press the yA Temp buttons for the desired heat setting Under Heating mode you can not select the fan speed In this mode you do not need to use the exhaust adaptor hose BUT the water collected must be discharged See Drainage Section 1 Press the MODE button until the Dry indicator lights 2 The fan will run at low speed and the display will show the room temperature 3 Keep doors amp windows closed for best effect Always have the exhaust hose attached in this mode When you Set the air conditioner in AUTO mode it will automatically select cooling heating not applicable for cooling only models or fan only operation depending on what temperature you have selected and the room temperature The air conditioner will control room temperature automatically round the temperature point set by you Under AUTO mode you can not select the fan speed In this mode there is no need to use the exhaust hose or drainage hose However if you require stale or smokey air to be removed from the room hook up the duct accessories as described in the EXHAUSTING HOT AIR section 1 Press the MODE button until the Fan indicator lights 2 Press
4. is blocked by drapes blinds furniture etc restricts air distribution Clear blockage in front of unit Doors windows registers etc open cool air escapes Close doors windows registers etc Unit recently turned on in hot room Allow additional time to remove stored heat from walls ceiling floor and furniture Dirty air filter air restricted Clean air filter Outside temperature extremely hot Set FAN speed to a faster setting to bring air through cooling coils more frequently Air movement sound This is normal If too loud set to lower FAN setting Vibraion from uneven floor Move or support appliance correctly on even surface Set temperature too low Increase set temperature Set temperature too high Lower setting If These Solutions Fail Call 1 800 944 9044 For Frigidaire Service 12 2009 Electrolux Home Products Inc All rights reserved Major Appliance Limited Warranty Your appliance is covered by a limited one year warranty and a limited 2 5 year warranty on the sealed system the compressor condenser evaporator and tubing For one year from your original date of purchase Electrolux will pay all costs for repairing or replacing any parts of this appliance that prove to be defective in materials or workmanship when such appliance is installed used and maintained in accordance with the provided instructions From the second to the fifth year from your original purchase date Electrolux wi
5. DURATION OF IMPLIED WARRANTIES SO THESE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU THIS WRITTEN WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS YOU MAY ALSO HAVE OTHER RIGHTS THAT VARY FROM STATE TO STATE If You Need Keep your receipt delivery slip or some other appropriate payment record to establish the warranty period Service Should service be required If service is performed it is in your best interest to obtain and keep all receipts Service under this warranty must be obtained by contacting Electrolux at the addresses or phone numbers below This limited warranty only applies in the USA and Canada In the USA your appliance is warranted by Electrolux Major Appliances North America a division of Electrolux Home Products Inc In Canada your appliance is warranted by Electrolux Canada Corp Electrolux authorizes no person to change or add to any obligations under this warranty Obligations for service and parts under this warranty must be performed by Electrolux or an authorized service company Product features or specifications as described or illustrated are subject to change without notice USA Canada 1 800 944 9044 1 800 265 8352 Electrolux Major Appliances Electrolux Canada Corp 10200 David Taylor Drive rd Electrolux 5855 Terry Fox Way Mississauga Ontario Canada L5V 3E4 Charlotte NC 28262 2009 Electrolux Home Products Inc All rights reserved 1 3
6. FRIGIDAIRE Use amp Care TABLE OF CONTENTS Important Safety Instructions c ssccesscrsseresers 2 3 Air Conditioner Features ccccssesessseeeeaeeereeees 8 Product RegiStireltl Oni yr eeye scr ss eae ener meee enters 4 Operating Instructions s a ame aeaa aa AA E 9 11 Normal SOUIMGS Ji sii cate eteelt estes tein tent teetenene 4 Care and Cleaning cteccs nese scree ss seee tee eeeeeee een 11 Unit Description cvvianeseneocsee ete ttn antt nant 5 Before You Call cccccuac se a ane 12 Accessories Included ss sssnssssreerrrerrrenrreeerrrerre 5 Major Appliance Limited Warranty c0cccceeeee 13 Installation Instructions amea 6 7 600Z un f O8SzvrsSzozozZ www frigidaire com USA 1 800 944 9044 www frigidaire ca Canada 1 800 265 8352 I mportant Safety I nstructions Note This USE amp CARE MANUAL provides specific operating instructions for your model Use the Portable air conditioner only as instructed in this USE amp CARE MANUAL These instructions are not meant to cover every possible condition and situation that may occur Common sense and caution must be practiced when installing operating and maintaining any appliance D Note The power supply cord with this air conditioner contains a current detection device designed to reduce the risk of fire Please refer to the section Operation of Current Device for details In the event that the power supply cor
7. URE BUTTON Vv A FAN SPEED SELECTOR MODE SELECTOR MODE rv speen mmer ow TIMER BUTTONS SLEEP BUTTON SLEEP SWING rer oF t SWING BUTTON H ON OFF BUTTON RESET LOCK i f PIN BUTTONS FRIGIDAIRE Fig 22 Battery Size AAA Warning 1 Do not mix old and new batteries Do not mix alkaline standard carbon zinc or rechargeable nickel cadmium batteries 2 This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation D note e The RESET button is depressed when you want to return to the initial factory settings The LOCK button is depressed to lock the keypad so the settings cannot be changed The key symbol will appear in the display of the remote control depress the LOCK button again to release Use a small pin to depress these buttons e Heating function is for heating and cooling model only Q 2009 Electrolux Home Products Inc All rights reserved Operating I nstructions Operating I nstructions D note The following instructions represent the Control Panel the same instructions can be used for the Remote Control except timer function COOLING MODE HEATING MODE on some models DRY MODE AUTO MODE FAN MODE TIMER OPERATION In this mode the exhaust adaptor hose MUST
8. d is damaged it cannot be repaired It must be replaced with a cord from the product manufacturer WARNING Avoid fire hazard or electric shock Do not use an extension cord or an adaptor plug Do not remove any prong from the power cord Grounding type wall receptacle Do not under any a circumstances cut remove or bypass the grounding prong Power supply cord with 3 prong grounding plug and current detection device SAFETY PRECAUTIONS WARNING For Your Safety Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance Read product labels for flammability and other warnings WARNING Prevent Accidents To reduce the risk of fire electrical shock or injury to persons when using your air conditioner follow basic precautions including the following Be sure the electrical service is adequate for the model you have chosen This information can be found on the serial plate which is located on the side of the cabinet If the air conditioner is to be installed in a window you will probably want to clean both sides of the glass first Be sure the air conditioner has been securely and correctly installed according to the installation instructions in this manual Save this manual for possible future use in removing or reinstalling this unit WARNING Electrical nformation The complete electrical rating of your new p
9. e light bulbs air filters water filters other consumables or knobs handles or other cosmetic parts 11 Surcharges including but not limited to any after hour weekend or holiday service calls tolls ferry trip charges or mileage expense for service calls to remote areas including the state of Alaska 12 Damages to the finish of appliance or home incurred during installation including but not limited to floors cabinets walls etc 13 Damages caused by services performed by unauthorized service companies use of parts other than genuine Electrolux parts or parts obtained from persons other than authorized service companies or external causes such as abuse misuse inadequate power supply accidents fires or acts of God DI SCLAI MER OF IMPLIED WARRANTIES LI MI TATION OF REMEDIES CUSTOMER S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR OR REPLACEMENT AS PROVIDED HEREIN CLAIMS BASED ON IMPLIED WARRANTIES INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW BUT NOT LESS THAN ONE YEAR ELECTROLUX SHALL NOT BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE AND INCIDENTAL EXPENSES RESULTING FROM ANY BREACH OF THIS WRITTEN LIMITED WARRANTY OR ANY IMPLIED WARRANTY SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSE QUENTIAL DAMAGES OR LIMITATIONS ON THE
10. lay type or reset circuit breaker Control is OFF Turn Control ON and set to desired setting P1 appears in the display window Drain water as described in Drainage Section Shut off in Heat mode When the air outlet exceeds 158 F 70 C the automatic heat protection engages Romove any blockages and let appliance cool down Room Temperature lower than the set temperature Cool Mode Reset the temperature Room Temperature higher than the set temperature Heat Mode Reset the temperature Room temperature below 60 F 16 C Cooling may not occur until room temperature rises above 60 F 16 C Reset to a lower temperature Compressor shut off by changing modes Wait approximately 3 minutes and listen for compressor to restart when set in the COOL mode Outdoor temperature below 60 F 16 C To defrost the coil set FAN ONLY mode Air filter may be dirty Clean filter Refer to Care and Cleaning section To defrost set to FAN ONLY mode Temperature is set too low for night time cooling To defrost the coil set to FAN ONLY mode Then set temperature to a higher setting Exhaust duct not connected or blocked See EXHAUSTING HOT AIR Section Dirty air filter air restricted Clean air filter Refer to Care and Cleaning section Temperature is set too high Set temperature to a lower setting Air directional louvers positioned improperly Position louvers for better air distribution Front of unit
11. ll repair or replace any parts in the Sealed Refrigeration System compressor condenser evaporator and tubing that prove to be defective in materials or workmanship In years 2 5 the consumer will be responsible for diagnostic labor and parts costs as well as any removal transportation and reinstallation expenses which are incurred during service on components other than those covered under the Sealed Refrigeration System 5 year warranty Exclusions This warranty does not cover the following 1 Products with original serial numbers that have been removed altered or cannot be readily determined 2 Product that has been transferred from its original owner to another party or removed outside the USA or Canada 3 Rust on the interior or exterior of the unit Products purchased as is are not covered by this warranty Food loss due to any refrigerator or freezer failures Products used in a commercial setting Service calls which do not involve malfunction or defects in materials or workmanship or for appliances not in ordinary household use or used other than in accordance with the provided instructions Service calls to correct the installation of your appliance or to instruct you how to use your appliance Expenses for making the appliance accessible for servicing such as removal of trim cupboards shelves etc which are not a part of the appliance when it is shipped from the factory 10 Service calls to repair or replace applianc
12. n Gurgle Hiss Gurgling or hissing noise may be heard due to refrigerant passing through evaporator during normal operation High pitched Chatter Today s high efficiency compressors may have a high pitched chatter during the cooling cycle Vibration Unit may vibrate and make noise because of uneven floor 2009 Electrolux Home Products Inc All rights reserved Unit Description amp Accessories I ncluded Unit Description ROOM AIR DISCHARGE CONTROL PANEL AIR INTAKE CARRYING HANDLE BOTH SIDES DEHUMIDIFYING EXHAUST DRAIN OUTLET AIR OUTLET REMOTE SIGNAL RECEIVER AIR INTAKE REMOTE CONTROL CASTOR Fig 1 BOTTOM TRAY DRAIN OUTLET Accessories I ncluded 3 4 Screw Fig 2 Check all the accessories are included in the package and please refer to the installation instructions for their usage 2009 Electrolux Home Products Inc All rights reserved 5 Installation I nstructions Installation I nstructions EXHAUSTING HOT AIR In the COOLING Mode the appliance must be placed close to a window or Opening so that the warm exhaust air can be ducted outside First position unit on a flat floor and make sure there s a minimum of 12 clearance around the unit and is within the vicinity of a single circuit outlet power source 1 Extend either side of the hose Fig
13. n to let the louver swing automatically Press the SWING button again while you want the louver stop at desired angle CHECK FILTER FEATURE This feature is a reminder to clean the Air Filter See Care and Cleaning for more efficient operation The filter indicator will illuminate after 250 hours of operation To reset after cleaning the filter press the Filter button and the light will go off SELECTING FAN SPEED You can select the desired fan speed by pressing the FAN SPEED button The fan AUTO LOW speed will change in the sequence as the drawing on the left NOTE After choosing the fan speed as LOW MED or HIGH the cooresponding fan speed indicator light will illuminate After the AUTO fan speed HIGH lt MED is selected no fan speed indicator light will illuminate Under AUTO Heat Dry mode you can not select the fan speed FAULT CODE If the display reads EA the room temperature sensor has failed Contact your Authorized Frigidaire Service Center If the display reads ES the evaporator temperature sensor has failed Contact your Authorized Frigidaire Service Center If the display reads E4 the display panel communication has failed Contact your Authorized Frigidaire Service Center If the display reads P1 bottom tray is full Carefully move the unit to a drain location remove the bottom drain plug and let the water drain away Restart the machine until the P1 symbol disappears If erro
14. ow is less than 26 6 inches Fig 12 3 Close the window sash securely against the window slider kit Fig 13 4 Drive two 1 2 screws to secure the window slider kit to the window sash screws FIG 13 5 Secure the window slider kit to the window stool FIG 13 A For wooden windows Use 3 4 screws for securing B For Vinyl Clad windows Use 1 2 hex head cap screws for securing 6 To secure lower sash in place attach right angle sash lock with 1 2 12 7mm screw as shown FIG 14 NOTE It is difficult to lock the windows with the sash lock for Vinyl Clad windows so you can use lock by window itself 7 Cut the foam seal to an appropriate length and seal the open gap between the top window sash and outer window sash as shown in Fig 15 Fig 10 1 2 screws gA Foam seal Fig 15 hex head cap screws Window stool Fig 13 Foam seal a adhesive type Installation in a sliding sash window 1 Cut the foam seals adhesive type to the proper lengths and attach them to the window frame See Fig 16 2 Open the window sash and place the window slider kit on the window stool See Fig 17 Attach the window slider kit to the window stool Adjust the length of the window slider kit according to the height of window Screw TEEN l l l down the two screws on the window slider kit See Fig 17 Cut the adjustable ee eee ren window slider kit if the height of window is les
15. r repeats call for service DRAI NAGE During the dehumidifying mode you will need a garden hose sold separately to drain the condensate from the unit Remove the rubber stopper from the hose connector then screw ona garden hose to the connector as shown on fig 23 The hose may then A Discharge into a drain that is lower than the unit B Be connected to a condensate pump sold separately C During cooling mode please replace the rubber stopper to the hose connector to reach the maximum performance Remove the supplied rubber stopper Garden hose Fig 23 1 0 2009 Electrolux Home Products Inc All rights reserved Operating Instructions CARE amp CLEANING Operating I nstructions continued ADDITIONAL THI NGS YOU SHOULD KNOW Now that you have mastered the operating procedure here are more features in your control that you should become familiar with The Cool circuit has an automatic 3 minute time delayed start if the unit is turned off and on quickly This prevents overheating of the compressor and possible circuit breaker tripping The fan will continue to run during this time Temperature can be set between 62 F and 86 F 17 C and 30 C The control is capable of displaying temperature in degrees Fahrenheit or degrees Celsius To convert from one to the other and back press and hold the TEMP Up A and Down
16. rotable air conditioner is stated on the serial plate Refer to the rating when checking the electrical requirements Be sure the air conditioner is properly grounded To minimize shock and fire hazards proper grounding is important The power cord is equipped with a three prong grounding plug for protection against shock hazards Your air conditioner must be used in a properly grounded wall receptacle If the wall receptacle you intend to use is not adequately grounded or protected by a time delay fuse or circuit breaker have a qualified electrician install the proper receptacle Do not run air conditioner without outside protective cover in place This could result in mechanical damage within the air conditioner Do not use an extension cord or an adapter plug DANGER Avoid Serious I njury or Death e This air conditioner contains no user serviceable parts Always call an authorized Electrolux servicer for repairs Do not insert or place fingers or objects into the air discharge area on top of the unit e Do not start or stop the air conditioner by unplugging the power cord or turning off the power at the electrical box Do not cut or damage the power cord If the power cord is damaged it should only be replaced by an authorized Electrolux servicer e Inthe event of a malfunction sparks burning smell etc immediately stop the operation disconnect the power cord and call an authorized Electrolux servicer e Do not opera
17. s than 26 6 inches Fig 12 3 Close the sliding sash securely against the window slider kit Fig 18 screws 4 Drive two 1 2 screws to secure the window slider kit to the window sash Fig 18 26 6 48 5 5 Drive two 3 4 screws to secure the window slider kit to the window stool Fig 18 6 Cut the foam seal to an appropriate length and seal the open gap between the sliding sash and outer window sash as shown in Fig 19 7 To secure the sliding sash in place attach right angle sash lock with 1 2 12 7mm screw as shown Fig 20 Window stool Window slider kit Foam seal 3 4 screws 1 S ETA eT 1 2 screws Fig 19 Fig 20 Fig 18 2009 Electrolux Home Products Inc All rights reserved 1 Air Conditioner Features Air Conditioner Features CONTROL PANEL DISPLAYS CHECK FILTER TEMPERATURE TIME RESET BUTTON m m i a on m dry m m auto hi fa oF hi m m filter filter m sleep reset off m fan m m cool al m med m m low timer vV A fan speed sleep on off L temp timer J Ne a SWING TURNS UNIT ON OR OFF BUTTON SETS MODE ADJUSTS SETS FAN SPEED TEMPERATURE ACTIVATES TIMER OR TIME SLEEP MODE Fig 21 REMOTE CONTROL Ca MODE INDICATION ANN auto Aan N ve hi ts He FAN SPEED SELECTION eat o lt TEMPERAT
18. sition To set the delay stop timing first press TIMER OFF button on the remote control to go to delay stop setting then tap or hold the TIMER OFF button to change delay stop timer at 0 5 hour increments up to 10 hours then at 1 hour increments up to 24 hours After the desired setting is reached stop pressing the TIMER OFF button the control will confirm the setting automatically after 5 seconds and change the display back to previous 2009 Electrolux Home Products Inc All rights reserved o Operating I nstructions Operating I nstructions continued temperature display Use the same way as above to set the delay start timing by pressing TIMER ON button To cancel the timer setting simply tap TIMER ON or TIMER OFF button to change the timing to 0 0 SLEEP OPERATI ON In this mode the selected temperature will increase by 2 F 30 minutes after the mode is selected The temperature will then increase by another 2 F after an additional 30 minutes This new temperature will be maintained for 7 hours before it returns to the originally selected temperature This ends the Sleep mode and the unit will continue to operate as originally programmed The Sleep mode program can be cancelled at any time during operation by again pressing the Sleep button Note This feature is unavailabe under FAN or DRY modes SWI NG OPERATION When you turn on the unit the louver will swing and stop at a certain angle You can press the SWING butto
19. te the air conditioner with wet hands e Do not pull on the power cord e Do not drink any water that is drained from the air conditioner 2 2009 Electrolux Home Products Inc All rights reserved I mportant Safety I nstructions SAFETY PRECAUTIONS CAUTION Avoid Injury or damage to the unit or other property e Provide occasional ventilation during use Do not direct airflow at fireplaces or other heat related sources as this could cause flare ups or make units run excessively e Do not climb on or place objects on the unit Do not hang objects off the unit e Do not place containers with liquids on the unit e Turn off the air conditioner at the power source when it will not be used for an extended period of time e Periodically check the condition of the unit s installation accessories for any damage Do not apply heavy pressure to the radiator fins of the unit e Operate the unit with air filter in place Do not block or cover the intake grille discharge area and outlet ports e Ensure that any electrical electronic equipment is one yard away from the unit Do not use or store flammable gases near the unit READ THIS SECTION BEFORE ATTEMPTING TO OPERATE AIR CONDI TI ONER Unit must be upright for one hour prior to operating The power supply cord contains a current device that senses damage to the power cord To test Operation of Current your power supply cord do the following Device 1 Plug in
20. the Air Conditioner 2 The power supply cord will have TWO buttons on the plug head Press the TEST button You will notice a click as the RESET button pops out 3 Press the RESET button Again you will notice a click as the button engages 4 The power supply cord is now supplying electricity to the unit On some model this is also indicated by a light on the plug head D note Do not use this device to turn the unit on or off Always make sure the RESET button is pushed in for correct operation The power supply cord must be replaced if it fails to reset when either the TEST button is pushed or it cannot be reset A new one can be obtained from the product manufacturer If power supply cord is damaged it CANNOT be repaired It MUST be replaced by one obtained from the product manufacturer Plug in amp press RESET 2009 Electrolux Home Products Inc All rights reserved 3 Product Registration amp Normal Sounds Product Registration Record Your Model and Serial Numbers Record in the space provided below the model and serial numbers On all models the serial plate is located on the side of the cabinet Model No Serial No Register Your Product The self addressed PRODUCT REGISTRATION CARD should be filled in completely signed and returned to the Frigidaire Company Normal Sounds Sound of Rushing Air At the front of the unit you may hear the sound of rushing air being moved by the fa
21. the FAN button to choose the desired fan speed 3 The fan will run at the selected speed and the display will show the room temperature You can set both delay stop and delay start while unit is in ON position or OFF position When unit is in ON position first press TIMER button to go to delay stop setting then timer off light will illuminate tap or hold the UP arrow A or the DOWN arrow V to change delay stop timer at 0 5 hour increments up to 10 hours then at 1 hour increments up to 24 hours Then press the TIMER button to confirm the setting the control will confirm the setting automatically after 5 seconds and go to delay start setting Use the same way as above to set the delay start timing If you don t need to set delay start press the TIMER button again to exit After 5 seconds the control will automatically change the display back to previous temperature display If you want to check remain timing press the TIMER button The delay start operation automatically selects mode temperature and fan speed the same as last operation you set When unit is in OFF position press TIMER button will first go to delay start setting then timer on light will illuminate set the delay start and delay stop timing the same way as above To cancel the timer setting simply tap A or V button to change the timing to 0 0 You can set both delay stop and delay start by using the remote control while unit is in ON position or OFF po
22. unplug the air conditioner to prevent shock or fire hazard The cabinet and front may be dusted with an oil free cloth or washed with a cloth dampened in a solution of warm water and mild liquid dishwashing detergent Rinse thoroughly and wipe dry Never use harsh cleaners wax or polish on the cabinet front Be sure to wring excess water from the cloth before wiping around the controls Excess water in or around the controls may cause damage to the air conditioner Winter Storage If you plan to store the appliance during the winter cover it with plastic or return it to its carton All rights reserved 11 Before You Call Before calling for service review this list It may save you time and expense This list includes common occurrences that are not the result of defective workmanship or materials in this appliance OCCURRENCE Air conditioner will not operate Air from unit does not feel cold enough Air conditioner cooling but room is too warm ice forming on cooling coil behind decorative front Air conditioner cooling but room is too warm NO ice forming on cooling coil behind decorative front Air conditioner turns on and off rapidly Noise when unit is cooling Room too cold Room Too Hot SOLUTION Wall plug disconnected Push plug firmly into wall outlet Plug Current Device Tripped Press the RESET button House fuse blown or circuit breaker tripped Replace fuse with time de
Download Pdf Manuals
Related Search