Frigidaire FBD2400KB Installation Instructions
Contents
1. leaving elbow pointing toward rear of unit To prevent bending of bracket or breaking of valve avoid overtightening 6 If using 4 hose thread fitting do not use teflon tape tighten elbow Do not over tighten Cabinet Preparation As a precaution it is recommended but not required that the cabinets enclosing all sides of the dishwasher including the underside of the countertop be sealed with an oil based paint or moisture proof polyurethane to prevent possible steam moisture damage Roughing In 3 A WARNING Electric Shock Hazard Observe all local codes and ordinances for electrical and plumbing connections All electrical and plumbing work should be performed by qualified persons Failure to follow this warning could result in death or serious injury 1 Make sure your location has the right drain water and electrical outlets to make the connections Do not install unit under a cooktop range Damage to plastic tub will occur 34 4 min E 6 O 91 2 LE AN 217 a 24 Figure2 Electrical water and drain lines mustbeconfined toshadedarea Electrical IMPORTANT For proper operation and appearance of unit cabinet opening should have dimensions as shown in Figure 2 If unit is to be placed in a corner there must be at least a 2 inch side clearance to open door 2 Remove any carpet from area to provide motor clearance Floor should be flat and free of any obstruction IMP2. not included at box to stabilize wiring IMPORTANT Be sure electrical cable is not routed behind dishwasher s motor Through Al Floor Junction Box in place Figure 12 3 Inside junction box attach ground wire under head of grounding screw and tighten See Figure 13 4 Connect incoming black lead to dishwasher s black lead and incoming white lead to dishwasher s white lead with wire nuts or other suitable connectors not included Wire nuts should be tight Conduit Connector notincluded Ground Wire White Wire to White Wire Neutral Black Wire to Black Wire Hot Junction BoxCover Figure 13 5 Replace junction box cover See Figure 13 Securing the Dishwasher 9 The dishwasher must be secured to keep it from tilting when door is opened Choose one of the methods described below to secure unit Countertop Anchoring 1 Install the Cabinet Seal Kit Instructions included in Kit 2 Replace Kickplate See Figure 1 3 Adjust levelers see Step 5 so mounting brackets touch underside of countertop IMPORTANT Dishwasher must rest on floor do not hang from countertop See Figure 14 4 Tub needs to be even with the front of adjoining cabinets 5 Screw mounting brackets firmly to countertop using screws provided in literature packet 6 Open and close dishwasher door slowly If door hits mounting brackets lower the dishwasher in front and rear Note Open and clos
3. drain system Choose method that best suits your need Figure5 Sinkat Left 2 Drain Hose Hole 2 If you connect to a sink drain entry will need to be above trap A Y branch tailpiece and connector kit not included will make this method easier and includes all needed fittings and instructions See Figure 5 Figure6 RightSide Installation 3 If you connect to a sink trap local codes may require you to install an air gap kit not included The drain hose will be routed from dishwasher to air gap inlet as shown in Figure 6 An air gap kit is available from a plumbing supply store NOTE If the drain hose is installed through the floor an air gap is necessary 4 If you connect to a disposer the large end of drain hose will fit Figure 7 a The knock out plug must be removed from inside disposer inlet before making the final fit to drain hose See Figure 7 b Largerend ofhose fitsdisposer inlet fitting Drain Hose Drain Air Gap Sinkat Left Sinkat Right 2 Drain Hose Hole Figure 7 b 5 Before cutting drain hose access check both sides of selected area to avoid interference Cut a 2 diameter hole in shaded area shown in Figure 2 6 Ifthe cabinet wall is wood sand edges of hole until smooth and rounded If cabinet wall is metal cover all sharp edges with electrical or duct tape to avoid cutting drain hose Drying Vent Hose if equipped Care must be given during installat
4. remove two 2 screws from inner door Save screws to reassemble See Figure 16a 2 Close and latch door while holding both sides 3 Place one hand on Figure 16b each side of door and pull down at top approximately 4 Pull entire door assembly toward you to remove See Figure 16b Appearance ofconsoleanddoormay vary from your model 6 Place door where it will not get scratched or damaged while completing installation When ready to replace door fit the slots on each side of top door edge over the tabs on the metal liner Push on sides to insure the door is flat Push up from bottom until there is no gap between door and console See Figure 16c Figure 16c Appearance ofconsoleanddoormay vary from your model Unlatch door and open while supporting outer door on both sides at bottom to keep in place Align screw holes and replace screws Checking the Installation 77 check these items Drain hose is assembled to drain pump All packing materials and consumer literature have been removed from unit Dishwasher is level and securely fastened Open and close door to make sure it does not hit surrounding cabinet or countertop Water and drain lines have no kinks Wiring connections to junction box are tight Water supply is turned on Joints are free of leaks Replacing Door 4 Refer to Step 10 numbers 5 and 6 for replacing outer door Adjus
5. Dishwasher Installation Instructions INSTALLER Leave nstallation Instructions with owner OWNER Read your dishwasher Use and Care Manual it contains important safety information for operating this appliance It also has many suggestions for getting the best results from your dishwasher PN 154427301 G AW 154427301 007 5 14 Before You Begin Read all instructions before installing dishwasher For your safety please read and observe all safety instructions This guide will help you anticipate drain water and electrical connections and help you select the best location for the A WARNING Tip Over Hazard Printed in U S A Do not use dishwasher until completely installed Do not push down on open door Failure to follow this warning can result in serious injury Installation Tips Tools and Materials Needed for Installation e Drill Electric e Driver Socket 54 1 g2 tg 2 tig e Flaring Tool Tube Cutter for copper tubing e Flashlight e Gloves e Level e Pipe Joint Compound for iron pipe plumbing or Pipe Thread Tape for sealing threads e Pliers e Safety Glasses e Saw Keyhole or 1 to 2 Hole Cutters e Screw Drivers Slotted and 2 Phillips magnetic tip preferred e Tape Electrical or Duct e Tape Measuring e Wire Stripper or Utility Knife e Wrench Hex end e Wrenches 2 Adjustable for copper tubing or 2 Pipe wrenches for iron pipe plu
6. ORTANT Drain water and electrical lines should be roughed in before going any further A WARNING Electric Shock Hazard Electrical water and drain lines must be confined to shaded areas in Figure 2 Electric conductors water and drain could be damaged Failure to follow these instructions could result in fire or electric shock NOTE If dishwasher is installed at end of a cabinet line sides and back must be fully enclosed NOTE You can order a Cabinet Seal Kit Kit 154528701 by contacting your dealer or parts supplier This kit provides a seal between the unit and cabinets once installation is complete Connections For Electrical 4 Water and Drain IMPORTANT Do not cross drain water and electrical lines in front of dishwasher motor or frame Locating the Connections 1 Review dimensions in Figure 3 to locate dishwashers drain water and electrical connections 2 All connections must be made in shaded area in Figure 2 Figure 3 Front a LeftSide Right Side e 40 k 22 1 2 Doorin openposition EN 17 4 gt Fromrearto junctionbox From floor to water inlet valve Fromrearto centerof water inletvalve Junction Box not visible DIMENSIONS DO NOT INCLUDE INSULATION IMPORTANT Disconnect power before starting installation Electrical 1 The dishwasher operates on a 120 volt 60 Hz electrical supply Provide a separate circuit with a fuse or circuit breaker ra
7. e door to make sure it does not hit surrounding cabinets or countertop Use Phillips Head Screws 8 x included in the literature packet Figure 14 Floor Anchoring This procedure is difficult and should be used only if countertop mounting brackets cannot be used 1 Screw lag screws not included through holes provided in frame rail See Figure 15 2 Use expansion fasteners if floor is concrete Before starting the dishwasher Use Lag Screws notincluded Figure 15 Note If mounting your dishwasher to the countertop or to the floor is not a desirable option you can order the side mount kit 154806601 02 by contacting your dealer or parts supplier This allows you to install the dishwasher by securing it to the cabinets or partitions on either side of the unit The kit utilizes the front frame of the dishwasher to secure the unit to the cabinet or partitions Removing amp Replacing Door 10 A WARNING Electric Shock Hazard Disconnect electrical power at the fuse box or circuit breaker box before beginning installation Failure to follow this warning could result in death or serious injury A CAUTION Cut Hazard Metal color panels are sharp and should be handled with care Wear gloves to protect hands Failure to follow this warning may result in injury To Remove and Replace Outer Door Fi 1 1 Unlatch and open pane rag door Using a Phillips head screw driver
8. et valve clogs make sure water supply is off If using a 3 3 NPT valve remove four 4 screws at inlet end of valve and clean filter screen If using 4 hose thread fitting simply clean filter screen Finishing the Electrical 8 Connection A WARNING Electric Shock Hazard Make sure electrical power has been disconnected at fuse box or circuit breaker box The dishwasher must be connected to a grounded metal permanent wiring system The equipment grounding conductor must be run with the circuit conductors and connected to the appliance s equipment grounding terminal or lead It is the consumer s responsibility to contact a qualified installer to make sure the electrical installation conforms with the National Electrical Code and local codes and ordinances Do not connect the dishwasher to the power supply until the appliance is permanently grounded All wiring connections must be enclosed in the junction box This unit has copper lead wires Joining aluminum building wire to stranded copper wire should be done by a qualified electrician using materials recognized by UL and local codes Do not use an extension cord Such use can result in fire electrical shock or other personal injury Failure to follow these instructions could result in death or serious injury Electrical Supply 1 Remove junction box cover and pull house wiring into junction box See Figures 12 and 13 2 Usea UL listed conduit connector
9. he inner door See Figure 9a a l lN i SS if P A l E i gt i Figure 9a Figure 9b Remove lower rack to check that dishwasher is level from front to back by placing the level at the bottom of the tub at the lower rack wheel support See Figure 9b Adjust levelers up or down until dishwasher is level Finishing the Drain Connection A WARNING Electric Shock Hazard Plumbing material and drain hose must not come in contact with wiring or electrical components Failure to follow this warning could result in personal injury from exposed wiring Pull out unit and check to see if drain hose is correctly attached to the drain pump assembly If drain hose is not attached to drain pump follow the instruction sheet included with drain hose on how to correctly install the drain hose to the drain pump assembly Move unit back in place while routing drain hose through access hole Use caution to prevent damage to the dishwasher floor and cabinets IMPORTANT Make sure there are no sharp bends or kinks that might restrict drain flow Secure drain hose to sink drain disposer or separate trap with a clamp IMPORTANT Be careful not to overtighten clamp or you may damage end of hose Do not connect hose to horizontal pipe between sink drain and disposer Be sure unit does not res
10. ion and removal of the dishwasher to avoid disconnection of the vent hose that is attached to the top of the dishwasher Drying Vent Hose 1 Leveling Dishwasher within Cabinets Measure height of cabinet opening from underside of countertop to floor Check chart for height opening and suggested adjustment Leg Leveler Adjustment Chart Height of Number of Turns to Cabinet Opening Adjust Levelers 34 86 4cm 0 34 s 86 7cm 2 345 16 87 2cm 6 34 2 87 6cm 9 For additional height add shims under levelers Move dishwasher to front of installation area Loosen the front and rear leveling legs by turning counterclockwise Refer to chart for number of turns See Figure 8 Front levelers should allow 1 7 below underside of countertop 5 39 Socket Front Leveler Wrench Rear Leveler Figure 8 If levelers have to be removed make sure floor is free of obstructions Place dishwasher inside cabinet area so that it is centered in opening Use caution when moving dishwasher to prevent damage to dishwasher floor and cabinets Remove lower rack to check that dishwasher is level from side to side by placing a level on the bottom of t
11. mbing Parts You Will Need Not Included e Drain Hose Clamp 1 Diameter e Elbow 90 with a s National Pipe Thread or 4 Hose Thread Fitting e Conduit Connector e Wire Nuts two 2 for 12 14 gauge wire e Plumbers Tape If required Available at e Y Branch Tailpiece and Plumbing Supply Store Connector Kit See Step 4 e Air Gap Kit See Step 4 Plumbing Supply Store e Fasteners for floor Hardware Store anchoring See Step 9 NOTE Recommended to use Stainless Steel braded hose A WARNING Electric Shock Hazard Disconnect electrical power at the fuse box or circuit breaker box before beginning installation Failure to follow this warning could result in death or serious injury e Examine dishwasher and locate connections See Step 4 e Locate dishwasher where there is easy access to drain water and electrical lines The best location is on either side of the kitchen sink for access to existing plumbing and ease in loading dishes See Step 4 e Electrical water and drain connections are not the same for all age brands or models of dishwashers Check the location and length of home utilities See Step 4 e A 15 20 amp grounded 120 volt AC only electrical supply is required See Steps 4 and 8 e If dishwasher drain hose will be connected to a food disposer for the first time knock out plug located inside disposer inlet See Steps 4 and 6 e Kinked water or drain hoses ca
12. n cause problems See Step 6 e Dishwashers need to be connected to a hot water supply with enough water pressure to insure an adequate fill See Steps 4 and 7 e Each home installation differs You will need additional parts listed above to complete your installation See Steps 4 and 7 e Flush water line prior to making the final connection to prevent clogging of dishwasher s filter screen See Step 7 e The dishwasher will look sound and perform best when properly leveled See Step 5 NOTE If levelers are removed during installation make sure the floor is flat and free of any obstruction e Anchor the dishwasher See Step 9 Installation Preparation 1 Remove two 2 screws at front of the kickplate assembly using a 2 Phillips screw driver 2 Tilt and pull forward to remove See Figure 1 NOTE It is not necessary to remove the outer door for installation However you might find it more convenient to do so You can find directions for removing door in Step 10 Water Inlet BottomScrews Valve So Kickplate Insulation available some models Figure 1 3 Locate water inlet valve behind kickplate on bottom left underside of unit The valve has a s NPT or 3 4 hose thread fitting Note If using 4 hose thread fitting skip steps 4 and 5 4 Wrap 90 elbow not included with pipe thread tape or apply joint compound and thread it into water inlet valve 5 Tighten elbow with a wrench
13. t door springs to balance weight of door A correct spring setting allows door to remain horizontal in opened position yet will rise to close with slight lift of finger If necessary increase tension by moving springs to a hole toward rear of unit or decrease by moving them toward front Turn electrical supply on Operate the machine through at least one fill and pump out checking the following items At first fill make sure water completely covers filter surface Motor pump sound may be heard before water enters unit At pump out make sure all water is pumped out Check water connections again for leaks A WARNING Electric Shock Hazard If all connections are correct there are no leaks and unit runs properly replace the kickplate assembly before placing unit into operation Failure to follow this warning could result in electric shock
14. t on drain hose It should be free of electrical components and door springs Do not cut corrugated drain hose Pull excess through cabinet and place under sink Make sure hose does not come in contact with any sharp edges See Figure 10 Sinkat Left The drain hose loop must be atleast 32 high from the floor toinsure proper drainage Finishing the Water Connection A CAUTION Property Damage Do not solder within 6 of the water inlet valve Damage to the plastic parts in the valve may occur Use care that no sealer dirt or other objects enter the valve Damage to the filter screen may occur Be sure the dishwasher is placed where the water inlet valve will be kept from freezing If the valve freezes it may rupture and flooding may occur Water Line 1 Flush water line before connecting it to water inlet valve to prevent early clogging of filter screen Place a bunched towel over end of line to prevent splashing Open water supply valve for a few seconds and let water drain into a pan Turn off water supply at shut off valve Figure 11 a Through Wall Through Cabinet Route water line to water inlet valve as shown in Figure 11 While firmly pulling water supply line into 90 elbow tightly connect water supply to water inlet valve Supply line must be free of kinks scales chips and lubricants Turn on water supply and check for leaks If water inl
15. ted for at least 15 amps 20 amps if connected with disposer but not more than 20 amps 2 Note the locations of electrical supply and dishwasher s electrical junction box on right underside of unit behind kickplate assembly See Figure 3 3 Cut access hole in shaded area shown in Figure 2 4 Pull electrical cable through hole into installation area Water 1 Determine where you will connect to hot water supply Review Figure 3 and note the location of water inlet valve A CAUTION Property Damage Do not use the furnished drain hose or a rubber garden hose for the water supply line Either of these hoses can burst Flooding may occur and cause property damage 2 Be sure water inlet valve is protected from freezing If valve freezes and ruptures flooding may occur 3 Determine amount of tubing needed to connect hot water supply to the unit s water inlet valve Copper tubing must have a minimum 3 s OD High pressure and high temperature rated plastic tubing with a minimum inner diameter of 2 may be used A shut off valve installed outside dishwasher cabinet is best See Figure 4 Figure4 4 Cut water access hole in shaded area in Figure 2 5 Route water supply line into installation area IMPORTANT Incoming hot water temperature should be at least 120 F 49 C Water pressure should be between 20 120 psi Drain 1 Review Figures 5 6 and 7 to see the different ways to connect dishwasher to
Download Pdf Manuals
Related Search