Fortinet 3000B User's Manual
Contents
1. DB9 Serial LH ower connection ti connections eoio Ethernet Ethernet future use connections connections Connecting O O Connect the following to the FortiManager system Ensure the FortiManager system is placed on a stable surface or securely mounted in a 19 rack e Insert the hard disks included in the FortiManager package into the bays of the Power connections FortiManager unit starting in bay 1 Use the diagram on the front panel as a guide BG e Insert a network cable to port 1 Insert the other end to the router or switch connected i HAHAHAHAA AHAHHH to the network seecee cence secceceeccsces es s Connect hord t ly Connect the oth dt o e onnect one power chord to a power supply Connect the other power cord to an aE oS poi H alternate power source if available om amp W oM a z e Connect the Power Cord to a surge protected power bar or power supply Null modem cable connects g e Press the Power button to turn on the FortiManager unit to serial port on management T e The power LED appears blue and the hard disk icon LED flashes blue while the system computer Straight through Ethernet boots cable connects to hub or For more information see the FortiManager Install Guide switch on the network Configuration Tools Web based manager Command Line Interface CLI The FortiManager web based manager is an easy to use management tool The CLI is a full featured management tool Use it to configure2. EET The light flashes orange when packets are sent and received on p zt the Ethernet port 1 and 2 FortiManager 3000B Power indicator is blue when the FortiManager system is on oz The light flashes blue when reading the boot device Hard Disk Upper LED Blue when the hard disk is properly inserted into the drive bay and the FortiManager is plugged in to a power source Flashes blue when reading and writing to the hard disk Formmanrser 3000B Visit these links for more information and documentation for your Fortinet product m l l T Tms r A Copyright 2009 Fortinet Incorporated All rights reserved e Technical Documentation http docs fortinet com Products mentioned in this document are trademarks or registered trademarks e Fortinet Knowledge Center http kb fortinet com of their respective holders e Fortinet Technical Support http support fortinet com Sheard a a eae 02 40000 112745 20091027 _ e Training Services http campus training fortinet com 11 March 2010 Package Contents A Connection to the internal network Optional connection to the management computer Provides access to the command line interface Front LED Indicators Power Button Power Suppy Alarm Reset Button Forernmanraser 3000B FSRTINET Straight through DB 9 Serial Cable and cross over Ethernet cables CN KO FSRTINET m REGISTER hard disks Power Cables p
3. password Enter a new password in the New Password and Confirm Password fields Click OK OakWnN gt Adding an administration password using the CLI To add an administration password in the CLI enter the following commands config fmsystem admin user edit admin set password please input password value lt password gt General settings Beraut Gateway J Primary DNS Sera Secondary DNS semer oU A default gateway is required for the FortiGate unit to route connections to the Internet Network Settings Factory default settings Port 1 interface 192 168 1 99 Port 2 interface 0 0 0 0 Port 3 interface 0 0 0 0 DHCP server on Internal interface 0 0 0 0 To reset the FortiGate unit to the factory defaults in the CLI type the command execute factory reset Command Line Interface The unit has serial port Use the null modem cable to connect it to your management com puter To connect to the unit 1 Use a null modem cable to connect the serial port to the management computer serial port 2 Start a terminal emulation program such as HyperTerminal on the management com puter Use these settings Baud Rate 9600 Data bits 8 Parity None Stop bits 1 Flow Control None 3 At the login prompt type admin and press Enter twice The login prompt is preceded by the server default host name After connecting to the CLI you can configure the unit IP address DNS server IP address and defaul
4. t gateway to connect the unit to the network To configure the unit using the CLI 1 Set the IP address and netmask of the Port1 interface config fmsystem interface edit portl set ip lt intf_ip gt lt netmask ip gt end 3 Configure the primary and secondary DNS server IP addresses config fmsystem dns set primary lt dns server ip gt set secondary lt dns server ip gt end 4 Configure the default gateway config fmsystem route edit 1 set device lt interface gt set dst lt destination_ip gt set gateway lt gateway ip gt end Shutting down the unit When powering off the unit always shut down the unit using the following procedures before disconnecting the power supply Not following this procedure can increase the risk of damag ing the hard disk To power off the unit Go to System Settings gt General gt Dashboard In the System Operation list select Shut Down Click Go Once the indicates the shut down procedure has completed disconnect the unit from the power source Pon gt Shutting down the unit using the CLI Enter the following command at the prompt execute shutdown
5. the administrator password Use it to configure the administrator password the interface and default gateway addresses the interface addresses the default gateway address and the DNS server addresses To and the DNS server addresses configure advanced settings see the Tools and Documentation CD ROM Requirements Requirements An Ethernet connection between the FortiManager system and management computer The DB9 serial connection between the FortiManager system and management com e Aweb browser such as FireFox 2 0 and higher or Internet Explorer 6 0 and higher on puter the management computer e Aterminal emulation application HyperTerminal for Windows on the management computer Collecting Information Interface configuration C Cd C Cd Port 1 Interface Port 2 Interface C i C The interface IP address and netmask must be valid for the internal network Port 4 interface Configuring T Web based Manager Use the following procedure to connect to the web based manager for the first time Configu ration changes made with the Web Config are effective immediately without resetting the unit or interrupting service To connect to the web based manager 1 Connect the Port 1 interface of the unit to Ethernet port of the management computer Use a cross over Ethernet cable to connect the devices directly Use straight through Ethernet cables to connect the devices through a hub or switch 2 Config
6. ure the management computer to be on the same subnet as the Port 1 interface To do this change the IP address of the management computer to 192 168 1 2 and the netmask to 255 255 255 0 3 To access the web based manager in your browser go to https 192 168 1 99 remem ber to include the s in https 4 Type admin in the Name field and select Login After connecting to the Web based manager you can configure the unit IP address DNS server IP address and default gateway to connect the unit to the network To configure interfaces Go to System Settings gt Network gt Interface Click the edit icon to configure each interface Set the IP address and netmask for the interface Click OK PONS To configure the Primary and Secondary DNS server IP addresses 1 Goto System Settings gt Network gt DNS enter the Primary and Secondary DNS IP addresses click Apply To configure a Default Gateway 1 Goto System Settings gt Network gt Static Routing and select Create New 2 Set Gateway to the Default Gateway IP address and click OK Adding an administration password By default the admin user does not have a password To restrict access to the unit manage ment account add password for the admin user account To add the admin user account password Go to System Settings gt Administration gt Administrator Select the admin user name to edit the profile Select the Change Password checkbox Enter the old
Download Pdf Manuals
Related Search