Fluke 1060AM-NM-LRVAR User's Manual
Contents
1. Biomedical 1060AM NM LRVAR Local Remote and Flasher Alarms Operators Manual March 2005 Manual No 1060AMNMLRVAR 1 Rev 1 2004 2005 Fluke Corporation All rights reserved Printed in U S A All product names are trademarks of their respective companies Fluke Biomedical Radiation Management Services 6045 Cochran Road Cleveland Ohio 44139 440 498 2564 www flukebiomedical com rms Section 1 1 1 Section 2 Section 3 3 1 Appendix A A 1 Table of Contents Introduction een 1 1 Procedures Warnings and Cautions a 1 1 Instruction An Sen Sana San San Sana Len Ss E An Aa 2 1 General ERNEA 2 1 eziez 2 1 Receiving MSpeetNO AE 2 2 OVA alien ret ee dak ect AMAN AMAN AH e o m ee m en 2 2 Installations dada 2 3 Electrical aiei zlea 2 4 OPEN 2 5 Maintenance and Cleaning akan 3 1 TrouBleshooling ara 3 1 Applicable Drawings and Parts US A 1 Applicable Drawings and Parts Lis iaa A 1 Blank Page Introduction 1 Procedures Warnings and Cautions Section 1 Introduction 1 1 Procedures Warnings and Cautions The equipment described in this manual is intended to be used for the detection and measurement of ionizing radiation It should be used only by persons who have been trained in the proper interpretation of its readings and the appropriate safety procedures to be followed in the presence of radiation Although the equipment described in this manual is designed and manufactured in compli2. 2 6 Electrical interface The Local alarm 1060 024 requires power connections as follows See appendix A for the 1060 13 and 1060 024 drawings Terminate the input power to TB2 1 L1 of the Local alarm assembly at the end of this installation Earth ground to chassis lug items 17 and 18 in view A A of the local alarm assembly The L2 neutral connection white to TB1 8 Connect the 75 foot power interface male end cables 1060 022 to both J1 and J2 They are interchangeable Remove the dust cap and connect the 1060ds 24 ten foot cable assembly to J3 and connect the free end to the I O connector on the 1060am nm LR The Remote alarm 1060 034 require power connections as follows See appendix A for the 1060 023 and 1060 034 drawings 1 2 3 Earth ground to chassis lug items 21 and 22 in view A A of the remote alarm assembly The L2 neutral L2 connection white to TB1 8 Connect either female end of the power interface cable to P1 on the remote alarm chassis The Flasher alarm 1060 026 requires power connections as follows see appendix A for 1060 033 and 1060 026 drawings 1 2 Earth ground to chassis lug of the flasher alarm assembly Neutral L2 connection to ac flasher terminal 1 3 Connect the remaining female end of the power interface cable to P1 2 4 Instructions D Operation 2 7 Operation The red beacons and red leds are ON The flasher alarm is blinking
3. Connect the free end of the I O 1060ds 24 cable to the model 1060AM NM LR I O connector Connect the 1060AM NM 110 12 volt 500 mA power cube connector to the 1060AM NM LR power input The red beacons turn off and the green ones are on The green LED s are also on The flasher alarm is now off 2 5 1060AM NM LRVAR Operators Manual Blank Page Maintenance 3 Maintenance and Cleaning Section 3 Maintenance and Cleaning To prevent injury do not remove or insert lamp when unit is energized CAUTION To prevent damage to the lens do not use abrasive materials or cleaners Refer the parts lists for the required type of lamp After disconnecting power replace the lamp as follows 1 Insert a small flat blade screwdriver between the INSIDE locking mechanism and the lens Gently push down and then pry up while unseating the lens away from the mounting base Pull the lens up and off CAUTION To prevent property damage and injury do not touch glass with bare fingers Grasp glass with a soft clean cloth or with packaging supplied with the replacement lamp 2 Gently push down on the lamp twist and pull up to remove the lamp from the socket Install the new lamp by aligning the connector on the base of the tube with its mating socket then carefully press down into the socket Assemble the Lamp 3 Apply power to the signal and verify that the signal operates properly Periodically clean the beacons lens with
4. a soft cloth or sponge and water or a mild detergent solution to maintain optimum visibility Ensure that the lens is completely dry before assembling the unit Refer the parts lists for the required type of lamp After disconnecting power replace the lamp as follows 3 1 1060AM NM LRVAR Operators Manual 1 Slide the acrylic yellow panel out from either side of the chassis CAUTION To prevent property damage and injury do not touch glass with bare fingers Grasp glass with a soft clean cloth or with packaging supplied with the replacement lamp 2 Gently push in on the lamp twist and pull up to remove the lamp from the socket Install the new lamp s by aligning the connector on the base of the tube with its mating socket then carefully press down into the socket Slide out the yellow acrylic panel from the chassis flasher alarm Clean with a soft cloth or sponge and water or a mild detergent solution to maintain optimum visibility Ensure that the acrylic sign is completely dry before assembling the unit 3 1 Troubleshooting e Extreme care must be used when troubleshooting a system that has power applied e All standard troubleshooting precautions apply e Once a problem has been located remove all power before continuing with the repair e Personnel performing the following procedure must be familiar with the operation of the monitoring system and the location of each piece of equipment used in the system e I
5. must comply with Level B storage requirements as outlined in ANSI N45 2 2 1972 Section 6 1 2 2 The storage area shall comply with ANSI N45 2 2 1972 Section 6 2 Storage Area Paragraphs 6 2 1 through 6 2 5 Housekeeping shall conform to ANSI N45 2 3 1972 Level B components shall be stored within a fire resistant tear resistant weather tight enclosure in a well ventilated building or equivalent Storage of Fluke Biomedical instruments must comply with the following 1 Inspection and examination of items in storage must be in accordance with ANSI N45 2 2 1972 Section 6 4 1 2 Requirements for proper storage must be documented and written procedures or instructions must be established 3 In the event of fire post fire evaluation must be in accordance with ANSI N45 2 2 1972 Section 6 4 3 4 Removal of items from storage must be in accordance with ANSI N45 2 2 1972 Section 6 5 and 6 6 2 2 Instructions 2 Installation 2 5 Installation To prevent electrical shock ensure that power is disconnected before installing the alarms Installation of the 1060am nm Irvar consists of mounting the unit providing an electrical interface and performing an operational check The 1060 024 1060 034 and 1060 026 have four mounting holes inside each chassis with a 0 19 diameter clearance 1 Remove four sheet metal screws from the case assembly 1060 024 and 1060 034 Slide out the yellow acrylic panel from the chas
6. ance with all applicable safety standards certain hazards are inherent in the use of electronic and radiometric equipment WARNINGS and CAUTIONS are presented throughout this document to alert the user to potentially hazardous situations A WARNING is a precautionary message preceding an operation that has the potential to cause personal injury or death A CAUTION is a precautionary message preceding an operation that has the potential to cause permanent damage to the equipment and or loss of data Failure to comply with WARNINGS and CAUTIONS is at the user s own risk and is sufficient cause to terminate the warranty agreement between Fluke Biomedical Radiation Management Services and the customer Adequate warnings are included in this manual and on the product itself to cover hazards that may be encountered in normal use and servicing of this equipment No other procedures are warranted by Fluke Biomedical It shall be the owner s or user s responsibility to see to it that the procedures described here are meticulously followed and especially that WARNINGS and CAUTIONS are heeded Failure on the part of the owner or user in any way to follow the prescribed procedures shall absolve Fluke Biomedical and its agents from any resulting liability Indicated battery and other operational tests must be performed prior to each use to assure that the instrument is functioning properly If applicable failure to conduct periodic performance tests in acco
7. fa problem develops verify that the voltages at connection point inputs and outputs are present and that all wiring is secure Refer to Appendix A for drawings and parts lists e Ifa problem cannot be resolved using the drawings in the Appendix while applying the troubleshooting instructions found in this manual please contact Fluke Biomedical at 440 248 9300 for assistance 3 2 Appendix A Applicable Drawings and Parts List Appendix A Applicable Drawings and Parts List 4 1 Applicable Drawings and Parts List 1060 005 1060 005 1060 010 1060 010 1060 013 1060 024 1060 024 1060 023 1060 034 1060 024 1060 026 1060 026 1060 033 1060 022 1060DS 24 1060AMNMLRVAR 1 Main Assembly Main Assembly Parts List Alarm PCB Assembly Alarm PCB Parts List Local Alarm Schematic Local Alarm Assembly Local Alarm Parts List Remote Alarm Schematic Remote Alarm Assembly Remote Alarm Parts List Flasher Alarm Assembly Flasher Alarm Parts List Flasher Alarm Schematic Power Interface Cable I O Cable Assembly Manual Fluke Biomedical Radiation Management Services 6045 Cochran Road Cleveland Ohio 44139 440 498 2564 www flukebiomedical com rms
8. ngle male plug connector P1 to interconnect with the local alarms normally closed contacts Conduit fittings provide access for the neutral L2 and earth ground terminations The Flasher alarm includes an AC solid state timer that switches two 25W halogen lamps at a frequency of about forty flashes per minute 2 2 Specifications Dimensions Local Alarm Remote Alarm Flasher Alarm HxWxD pn 1060 024 Pn 1060 034 Pn 1060 026 9x 6 3 x 6 75 9 x 6 3 x 6 75 10 x 14x 2 in cm 22 9 x 16 0 x 17 1 22 9 x 16 0 x 25 4 x 35 6 x 5 1 17 1 Weight lbs Kg 3 Ib 1 4 2 5 Ib 1 1 3 lib 1 1 Operating 32 deg to 122 32 deg to 122 32 deg to 122 Temperature deg deg deg F C O deg to 50 deg Odegto50 deg O deg to 50 deg Relative Humidity 0 to 90 0 to 90 0 to 90 Non condensing 2 1 1060AM NM LRVAR Operators Manual Electrical Requirements 120 VAC 50 60 Hz 120 VAC 50 60 Hz 120 VAC 50 60hz 2 3 Receiving Inspection Upon receipt of the unit 1 Inspect the carton s and contents for damage If damage is evident file a claim with the carrier and notify Fluke Biomedical at 440 248 9300 2 Remove the contents from the packing material 3 Verify that all items listed on the packing list have been received and are in good condition If any of the listed items are missing or damaged notify Fluke Biomedical 2 4 Storage Storage of Fluke Biomedical instruments
9. rdance with ANSI N323 1978 R1983 Radiation Protection Instrumentation Test and Calibration paragraphs 4 6 and 5 4 and to keep records thereof in accordance with paragraph 4 5 of the same standard could result in erroneous readings or potential danger ANSI N323 1978 becomes by this reference a part of this operating procedure 1060AM NM LRVAR Operators Manual Blank Page Instructions 2 General Description Section 2 Instructions 2 1 General Description Refer to 1060 005 drawing located in Appendix A The Fluke Biomedical local remote and flasher alarms are used in conjunction with the Victoreen Model 1060AM NM LR The operating range of this system is 0 01 mR hr to 1R hr The red halogen lamps and the flashing yellow sign provides a remote 75ft and a local visual alarm indication The green incandescent lights operate at half power and indicate normal operating conditions while in a radiation field of less than 2mR hr 10 An efficient dual led red green operates in a similar fashion and shall alert personnel of a bulb burn out in either the local or the remote alarms The Local alarm also includes two female power connectors J1 and J2 each with a set of normally closed contacts J3 is a male connector with a dust cover that interfaces with the 1060am nm LR A inch conduit fitting is provided for the hot L1 neutral L2 and earth ground connections The Remote and Flasher alarm both have a si
10. sis from either side of the flasher alarm assembly 1060 026 2 Using a chassis as a template mark the mounting surface for hole positioning 3 Drill the necessary holes in the mounting surface 4 Secure the chassis with the appropriate screws 5 Determine a suitable location to mount the 1060am nm LR The alarm threshold is set at 2 mR hr A field between 10mr hr and a 100mr hr is good starting point Contact your radiation safety officer for your company requirements CAUTION If readings from a device s position indicates that the radiation rate is relatively high CAUTION should be observed when replacing or working on this unit High rates can quickly cause the operator s cumulative exposure to increase with the potential for injury 6 The 1060am nm LR may be queried for this radiation rate remotely with the RS 232 communications using the RRM command Read mR Hr averaged over 60 seconds Wait two minutes and repeat the command RRM as necessary See manual 1060am 1 for more information 7 A twenty five foot cable assembly pn 1060am nm 11 is available with a DB9F connector and a five pin circular connector If this length is inadequate use the connector kit supplied with the 1060am nm LR Select the 5 pin male and assemble your own Refer to the section labeled Connections 1060am nm NEMA 4 enclosure TXD RXD and GND are the signals required for RS 232 communications 2 3 1060AM NM LRVAR Operators Manual
Download Pdf Manuals
Related Search