Fisher LNS-T01Z User's Manual
Contents
1. W01Z LNS O LNS 1 C 1 z C C C C 1 1 1 1 111111 1 C L 4 L ICPWZ 1 AA6P1P2629 1 1 0 O 0 00 O 0 a 1 CJ cy Cd mo O U g O lO Cy LI lO El 11 1412 1 g mo 1 5 3 C4 d 1 1 1 oo oga a ag O CO oo oa Oooo LC C LC C LC C C C C C C2. C C C 1 2 0 1 11 111111 1 3 11 1 1 111111 1 1 111 1 100000000000 Bo 551000000000 FFT A 10 0 0 0 0 00 0 0 1 160 1 0000000 2000000060 1 1 1 1 1 11 1111111111 11111 3 00000 2 11 4 2 9000000000 8 0 0 0 0 0 8 8 9 8 0 0 0 0 0 8 8 8 0 0 410 00 7 U MD COC 1 1 1 6 11 1 1 1 00000000 Ull 000000 2 1 1 11111 11110 0 0 11 0 11 1 11 111
3. 11 30000 0 00000 0 0 00 00 00 0 g 11 111 1 aD C UJ 0000 000001 310 0 0 0000 0 0 0 004100 1 1 1111111111 1 1 1 1111111111 53 g o0 g H o 53 g H ooo 5 3 7 1 1 1111111111 400000000000000 05000 CJ CJ E CJ c 1 CJ El 1 1 1 5 7 0 0 0 0 0 0 0 0 m0 0 6000 1 11 11 11 11 lt CJ CJ E c CJ CJ CJ CJ E CJ CJ CJ E 1 E CJ E 1 1 CJ CJ E C4 N El CJ E Ed El CJ LCD PROJECTOR LENS MODEL NO LNS W01Z LNS T01Z LENS REPLACEMENT AND INSTALLATION PROCEDURES NOTES ON REPLACEMENT AND INSTALLATION The procedures and the needed pars for lens installation depend on the type of cabinet Before installing or replacing the lens make sure the type of cabinet and be sure to refer to the Installation Manual corresponding with your projector When installing or replacing the l
4. Some parts are not used for installation or replacement Keep these parts for later use Note Figures in this manual may be differ from the actual product LENS REPLACEMENT AND INSTALLATION PROCEDURE Perform the steps to for lens replacement and installation UPPER LENS COVER C REMOVE THE LENS COVER See figure 1 1 Remove screws 2 screws 2 Pull down the lower lens cover while pushing the part D then remove it 3 Remove screws B 2 screws 4 Remove screws C 2 screws and remove upper lens cover IN CASE OF MODEL WITHOUT LENS REMOVE THE COVER PLATE OF THE LENS COVER See figure 2 Remove 2 screws and pull down the plate At the step 4 insert the light block sheet alg the same position as the removed cover plate N has been placed Two screws not used Lo Set the light block sheet so that the large rounder side is set over the lens KA SCREWS COVER PLATE 4 IN CASE MODEL WITH LENS Figure shown inside of the cabinet LENS MOTOR REMOVE THE LENS See figure 3 1 Remove the connector K16B of the circuit board 2 Loosen the A B wire holder and remove the lens motor lead 3 Remove screws D 4 screws which fastens the lens and remove the lens LENS MOTOR LEAD Fig 2 CONNECTOR K16B INSTALL THE LENS See figure 4 1 Remove protective caps front an
5. d LENS MOUNTING BRACKET back on the lens 2 Mount the lens on mounting bracket of the main cabinet with 4 screws Use the screws included with the lens Use the driver included with the lens to fasten the screws After using save it for latter use INSTALL THE LIGHT BLOCK SHEET See figure 5 l FOCUS LENS LOCK SCREW Install the light block sheet around the lens as shown in the illustration Use the sheet included with the lens When this projector permanently install in the structure slide the picture obtain cor rect focus then lock the lens by Focus Lens Lock screw at this step Adjust focus by rotating the lens LIGHT BLOCK SHEET Fig 5 MOUNT THE LENS COVER See figure 6 When in install the both upper and lower UPPER LENS COVER lens covers install the light block sheet so that it should be placed in the guide slot place of the cover plate had been placed See figure 2 If the installation of light block sheet is incorrect it will be the cause of leakage of light or the dust entering at the main cabinet 1 Insert the upper part lens cover and fix them with screws A 4 screws 2 Insert the lower part lens cover and fix them with screws B 2 screws
6. ens make sure the Lens Model No matches with your projector Refer to the catalog or contact your sales dealer for the proper Lens Model No TYPE OF THE CABINET AND REFERENCE INSTALLATION MANUAL Refer to the Installation Manual corresponding to your projector See the chart below Type of the Cabinet Reference Installation Manual Refer to this manual Other than the above cabinet Refer to the Installation Manual design supplied with the Projector NOTES ON LENS INSTALLATION The ZOOM and FOCUS adjustment on the Top Control or the Remote Control can not be operated with this Lens Lens installation and replacement should be made by the qualified service per sonnel Be sure to install the lens following this procedure precisely e The lens cover is on the lens for protection Be sure to replace the lens cover before installation When installing or replacing the lens be careful not to stain scratch or damage the lens LIST OF CONTENTS Following parts are included in the packing e LENS 1 LENS MOUNTING SCREWS 2 pcs for spare e DRIVER 1 pe LIGHT BLOCK SHEET 1 pc BE SURE TO CHECK FOR SAFETY After installing or replacing the lens be sure to check the following for safety 1 Check the lens is securely fixed by 4 screws 2 Check no wiring is tangled on the gear of lens motor or the other mechanical parts 3 Check no part is missing or no mounting part is loose
Download Pdf Manuals
Related Search