Fisher-Price L3891 User's Manual
Contents
1. high chair pull the shoulder portions of the restraint system out and then fit them back through the desired shoulder strap slots in the seat pad and in the seat back e From behind the product attach the ends of the shoulder straps to the peg e You can remove the shoulder straps and use only the waist restraint From behind the product squeeze the restraint release tabs and remove the shoulder straps e From the front of the product pull to remove the shoulder straps from the seat back pad e Push to remove the shoulder straps from the waist restraint buckle slots e Store the shoulder straps in a safe in a safe place for future use Using the Trays WARNING Prevent serious injury or death from falls or sliding out Always use the restraint system for the upright and reclined positions of the seat Adjust restraint to fit your child snugly The tray is not designed to hold the child in the chair e You can adjust the base tray forward or backward While pulling the latches underneath the tray out adjust the base tray forward or backward 0 While pushing the release bar on the front of the base tray adjust the base tray forward or backward e While pulling the latches underneath the tray out slide it onto the armrests Release the latches to secure the tray in place Hint Before use thorougly wash all parts the trays that may contact food The base tray is not dishwasher saf2. IMPORTANT KEEP INSTRUCTIONS FOR FUTUREREFERENCE www fisher price com au Consumer Information WARNING Prevent serious injury or death from falls or sliding out e Always use the restraint system for the upright and reclined positions of the seat Adjust restraint to fit your child snugly The tray is not designed to hold the child in the chair e It is recommended that only children capable of sitting upright unassisted use the upright position of the high chair e Position the high chair away from steps hot surfaces electrical cords and other items that may cause injury to the child e Always leave wheels locked e Always keep child in view while in high chair e Never leave child unattended e Follow the manufacturer s instructions CAUTION This package contains small parts in its unassembled state Adult assembly is required IMPORTANT Place the high chair on a level stable surface away from electrical flexes Be sure to keep electrical flexes out of child s reach e Please read these instructions before assembly and use of this product e Adult assembly is required Tool needed for assembly Phillips screwdriver not included e Weight limit 22 7 kg 50 lbs e Product features and decorations may vary from photos Australia Mattel Australia Pty Ltd 658 Church Street Locked Bag 870 Richmond Victoria 3121 Australia Consumer Advisory Service 1300 135 312 e New Zealand 16 18 Wi
3. crotch belt e With the legs all the way open lower the seat to position 7 the lowest position e Pull the frame release latches forward and push the rear legs toward the front legs 2006 Mattel Inc All Rights Reserved and designate U S trademarks of Mattel Inc PRINTED IN CHINA Fisher Price Inc a subsidiary of Mattel Inc East Aurora New York 14052 U S A L3891pr 0729
4. adjusters and lift or lower the seat to the desired height e Make sure both sides of the seat are adjusted to the same height Push the seat bottom to be sure the seat is locked in place A aA A I BACK VI Hint Adjust the seat angle to any of three positions Upright Semi Recline or Recline To adjust the seat angle e Squeeze the seat back handle and push the seat back forward or pull it backwards to the desired position e Push the seat back to be sure it is latched in position e The pad frame and base tray may be wiped clean using a mild cleaning solution and a damp cloth Do not use bleach e The restraint system may be wiped clean or is machine washable Machine wash in cold water on the gentle ui cycle Do not use bleach Line dry l e The food tray teether toy and restraint system are also top rack dishwasher safe or use bottom rack without using the drying cycle To remove the pad e Remove the elastic loops from the pegs on the underside and back of the seat e From behind the product squeeze the restraint release tabs and remove the restraint system from the peg e From the front of the product pull to remove the restraint system e Unfasten the pad hooks from the front edge of the seat Lift the top of the pad off of the seat back e To replace the pad refer to Assembly steps 14 20 IMPORTANT Never use this product without the restraint system Replace the waist shoulder belts and
5. out Always use the restraint system for the upright and reclined positions of the seat Adjust restraint to fit your child Snugly The tray is not designed to hold the child in the chair Waist Shoulder Belt Waist Shoulder Belt e To tighten the waist straps Feed the anchored end of the waist strap up through the buckle to form a loop 0 Pull the free end of the waist strap e To tighten the shoulder straps Hold the adjuster and pull the shoulder strap down Crotch Belt e Place your child in the seat Position the crotch belt between your child s legs e Fasten both waist shoulder belts to each side of the crotch belt Make sure you hear a click on both sides e Check to be sure the restraint system is securely attached by pulling it away from your child The restraint system should remain attached To loosen the waist straps Feed the free end of the waist strap up through the buckle to form a loop Q Enlarge the loop by pulling on the end of the loop toward the buckle Pull the anchored end of the waist strap to shorten the free end of the waist strap To loosen the shoulder straps Lift the adjuster Note After adjusting the restraint system to fit your child make sure you pull on it to be sure it is securely fastened Secure Child To change strap slots e From behind the product squeeze the restraint release tabs and remove the shoulder straps e From the front of the Shoulder Straps
6. the seat bottom tubes move you have probably not fastened them properly Remove the screws and check to be sure the screw holes in the I ANTI JG seat bottom tubes and seat bottom plastic rings are aligned A Replace and tighten the screws Plastic Rings e Slide a seat bottom tube through each set of plastic rings on the seat bottom Assembly e Insert two 10 x 2 2 cm black screws through the footrest and into the seat bottom Tighten the screws Seat Back Pins e Turn the seat bottom assembly upright e Fit the seat back pins into the slots in the top side of the seat bottom assembly e Turn the seat assembly face down e Insert the hinge rod through the hinge on the seat back and seat bottom as shown e Insert a 10 x 2 2 cm black screw into the hinge rod Tighten the screw e Set the seat assembly aside for Assembly step 10 Frame Leg Lee e Pull the frame leg out on each frame to open Make sure it clicks into place Assembly Frame Decorated Side Back Base Screw Retainers e Position a frame so that the decorated side is outward e Insert the back frame legs into the back base e Fit a screw retainer over a hole in the back base as shown e Insert a 10 x 2 2 cm black screw through the screw retainer and back base Tighten the screw Repeat this procedure to fasten the other frame back leg to the other side of the back base Hint The 10 x 2 2 cm black screws may have been assemble
7. at bottom tubes e Insert a 8 x 1 9 cm screw through each seat height adjuster and the ends of the seat bottom tube Tighten the screws This may require extra force Assembly e Remove both shoulder straps from the seat back e Remove the crotch strap from the seat back Assembly Shoulder Straps Up Lowest Slot Crotch Strap Down e Fit the clips on the front edge of the pad onto the Hint Do not unbuckle the restraint system It is easier to seat bottom attach or re attach it to the product if it is buckled e Grasp the restraint system so that the shoulder straps are up and the crotch strap is down e Insert the end of the crotch strap through the lowest slot in the pad and the seat back e From behind the product attach the end of the crotch strap to the peg e Hook the elastic loops on each side of the pad onto the tabs in the seat back e From behind the product attach the end of the crotch strap to the peg Assembly Smaller Baby e Insert the ends of the shoulder straps Larger Baby e From the front of through the lower slots in the pad the product insert the ends of the shoulder From behind the product attach the ends of the shoulder straps to the peg straps through the upper slots in the pad and seat back e From behind the product attach the ends of the shoulder straps to the peg Secure Child WARNING Prevent serious injury or death from falls or sliding
8. d to the screw retainers Seat Height Adjusters Press Lever e While pressing the levers on the seat height adjusters lift them to position 4 on the frame front legs as shown Seat Assembly Seat Bottom Tubes e Fit the seat assembly between the two frames e Insert the seat bottom tubes into the sockets in each seat height adjuster Hints e Be sure the seat height adjusters are in the same position position 4 You may need to push the frames apart slightly to fit the seat bottom tubes into the seat height adjuster sockets Assembly Seat Height Adjusters Screw Retainers IN x OTT 7 Front Base Seat Bottom Tube Ends e Fit the frame front legs onto the front base e From the back and bottom of the assembly insert a 8 x 1 9 cm screw through both seat height adjusters and the ends of the seat bottom tube Tighten the screws This may require extra force e Fit a screw retainer over the hole in a front leg e Insert a 10 x 2 2 cm black screw through the screw retainer and front leg Tighten the screw e Repeat this procedure to fasten the other end of the front base with the remaining screw retainer and 10 x 2 2 cm black screw Hint The 10 x 2 2 cm black screws may have been assembled to the screw retainers e Squeeze the restraint release tabs together e Remove the ends of the restraint system from the peg e Push each seat height adjuster to be sure they are completely on the se
9. e e To remove the tray Pull one or both of the latches underneath the tray out and lift Q Push the release bar on the front of the tray and lift Using the Trays Food Tray Base Tray e Fit the food tray into the base tray as shown Hint Before use thorougly wash all parts the trays that may contact food The food tray is not microwave safe e Insert and snap the toy tab into either slot in the tray Hint To remove the toy press the tab and lift the toy Using the Brakes WARNING Prevent serious injury or death from falls or sliding out e Position the high chair away from steps hot surfaces electrical cords and other items that may cause injury to the child e Always leave wheels locked Wa Press Tab To Lock Press the tab on all four wheels down until vou hear a snap To Unlock Lift the tab on all four wheels up Adjusting the Seat WARNING Prevent serious injury or death from falls or sliding out Lul e Always use the restraint system for the soe FRUN Adjust upright and reclined positions of the seat Adjust restraint to fit your child snugly The tray is not designed to hold the child in the chair e It is recommended that only children capable of sitting upright unassisted use the upright position of the high chair Semi Recline Hint Adjust the seat beight to any of seven positions To adjust the seat height e Press the levers on both seat height
10. lliam Pickering Drive Albany 1331 Auckland e Asia Mattel East Asia Ltd Room 1106 South Tower World Finance Centre Harbour City Tsimshatsui HK China e Malaysia Diimport amp Diedarkan Oleh Mattel SEA Ptd Ltd 993532 P Lot 13 5 13th Floor Menara Lien Hoe Persiaran Tropicana Golf Country Resort 47410 PJ Tel 03 78803817 Fax 03 78803867 Seat Back 2 Frames Seat Bottom Back Base Front Base c Hinge Rod 2 Seat Bottom Tubes Food Trav Base Trav Note Tighten or loosen all screws with a Phillips screwdriver Do not over tighten the screws Qum jn 8 x 1 9 cm Screws 8 10 x 2 2 cm Black Screws 7 Shown Actual Size Assembly IMPORTANT Before assembly and each use inspect this product for damaged hardware loose joints missing parts or sharp edges DO NOT use if any parts are missing or broken Contact Mattel for replacement parts and instructions if needed Never substitute parts Footrest Seat Bottom e Place the seat bottom face down on a flat surface e At an angle fit the footrest to the seat bottom as shown Plastic Rings Seat Bottom Tubes e Align the holes in the plastic rings and the seat bottom tubes N if bl e Insert a 8 x 1 9 cm screw through each plastic ring and into ceci hi SA mi the seat bottom tubes as shown Tighten the screws This mav require extra force e Push the seat bottom tubes back and forth to be sure they are secured to the seat bottom If
Download Pdf Manuals
Related Search