Fisher-Price B8866 User's Manual
Contents
1. Seat Back Base Tray Seat Bottom Frame Hinge 10 x 2 2 cm 7 s8 Rod Black Screw 8 x 2 cm 4 Screws 2 Seat Bottom Tubes 3 4 x Screws Tee 4 Screw Retainers 10 x 2 2 cm 7 s Black Screw 4 Footrest 2 Bases i L 10 x 2 2 cm is j Black Screws 8 x 1 9 cm 3 4 Screw 8 SHOWN ACTUAL SIZE 10 x 2 2 cm 7 s Black Screw 7 N SHOWN ACTUAL SIZE y 3 Assembly IMPORTANT Before assembly inspect this product for damaged hardware loose joints missing parts or sharp edges DO NOT use if any parts are missing damaged or broken Contact Mattel for replacement parts and instructions if needed Never substitute parts Footrest Seat Bottom Align the holes in the plastic ay rings and the seat bottom tubes 8 1 9 cm 4 Screw 4 Insert a 8 x 1 9 cm 3 4 screw SHOWN ACTUAL SIZE into each plastic ring and tighten Push the seat bottom tubes back and forth to be sure they e Place the seat bottom face down on a flat surface are secured to the seat bottom If the seat bottom tubes At an angle fit the footrest on the seat bottom as shown move you have probably not fastened them properly Remove the screws and check to be sure the screw holes in the seat bottom tubes and seat bottom plastic rings are aligned Replace and tighten the screws Footrest 2 e Slide a seat bottom tube through each set of plasti2. FisherPrice Healthy Care High Chair Product features and decoration may vary from the photo above Model Number B8866 Please read these instructions before assembly and use of this product Adult assembly is required Tool needed for assembly Phillips Screwdriver not included A WARNING IMPORTANT KEEP INSTRUCTIONS FOR FUTURE REFERENCE Warnings and Caution Consumer Information Occasionally a consumer may experience a problem with one WARN f Ne of our products If this should happen please call us rather than return this product to the store Usually we can solve the problem over the telephone or send you replacement parts Please call 01628 500303 or write to Prevent serious injury or death Mattel UK Limited from falls or sliding out Mattel House e The child should at all times amal Uses Sac wear a safety harness correctly fitted and adjusted The tray is not designed to hold Vanwall Road Maidenhead Berkshire SL6 4UB the child in the chair Always keep child in view while in the high chair Never leave child unattended lt is recommended that the high chair be used in the upright position only by children capable of sitting upright unassisted A CAUTION This product contains small parts in its unassembled state Adult assembly is required Parts Note Tighten all screws with a Phillips screwdriver Do not over tighten the screws Food Tray
3. c rings A on the seat bottom 10 x 2 2 cm 7 8 e Insert two 10 x 2 2 cm 7 8 Black Screw 2 black screws through the foot SHOWN ACTUALSIZE gt rest and into the seat bottom Tq e Tighten the screws Assembly Frame Leg Seat Back Pin Opening Seat Bottom Assembly 5 e Pull the frame leg out on each frame to open Make sure it clicks into place e Turn the seat bottom assembly upright Fit the seat back pins into the openings in the top side of the seat bottom assembly A 10 x 2 2 cm 7 8 Black Screw SHOWN ACTUAL SIZE Turn the seat assembly face down e Insert the hinge rod through the hinge on the seat back and seat bottom as shown e Insert a 10 x 2 2 cm s black screw into the hinge rod and tighten e Set the seat assembly aside for Assembly step 10 Assembly Frame Decorated Side Seat Height Adjusters Press Lever aar o e While pressing the levers on the seat height adjusters lift them to position 4 on the frame front legs as shown Seat Assembly me D 10 x 2 2 cm 7 8 Black Screw 2 Screw Retainer 2 N SHOWN ACTUAL SIZE y E y e Position a frame so that the decorated side is outward e Insert the back legs of a frame into one of the bases e Fit a screw retainer over the hole in the base as shown e Insert a 10 x 2 2 cm 7 8 black screw into the screw retainer and ti
4. e crotch belt Make sure you hear a click on both sides e Check to be sure the restraint system is securely attached by pulling it away from your child The restraint system should remain attached 10 Securing Your Child mi Anchored To tighten the waist belts e Feed the anchored end of the waist belt up through the buckle to form a loop Q e Pull the free end of the waist belt e Repeat this procedure to tighten the other waist belt To loosen the waist belts e Feed the free end of the waist belt up through the buckle to form a loop Q Enlarge the loop by pulling on the end of the loop toward WYO the buckle Pull th RRP d of th mee orten the f To change shoulder belt slots e Pull the anchored end of the waist belt to shorten the free end of the waist belt From the back of the high chair push the shoulder portion of the waist shoulder belts through the seat back slots ic Fe m E ao En e Repeat this procedure to loosen the other waist belt Hold Shoulder _ Adjuster Portion Slide Pull Strap Adjuster Down D _ Down Tighten Loosen To tighten the shoulder belts Hold the adjuster and pull the front shoulder strap down To loosen the shoulder belts Slide the adjuster down e From the front of the high chair pull the shoulder portion of Note After adjusting the restraint system to fit your child the waist shoulder belts out and then fit them back
5. ghten e Repeat this procedure to fasten the other frame back leg to the other side of the base with a screw retainer and 10 x 2 2 cm s black screw Seat Bottom Tub Hint The 10 x 2 2 cm 7 s black screws may have been assembled to the screw retainers e Fit the seat assembly between the two frames e Insert the seat bottom tubes into the sockets in each seat height adjuster Hints Be sure the seat height adjusters are in the same position position 4 You may need to push the frames apart slightly to fit the seat bottom tubes into the seat height adjuster sockets Assembly Front Leg Holes Seat Bottom Tube Ends ANNAN 8 x 1 9 cm 3 4 Screw 2 SHOWN ACTUAL SIZE e Push each seat height adjuster to be sure they are completely on the seat bottom tubes e Insert a 8 x 1 9 cm 3 4 screw into each seat height adjuster and the ends of the seat bottom tube e Tighten the screws ae 8 x 1 9 cm 3 4 Base Cc Screw 2 s Ff T SHOWN ACTUAL SIZE E 10 x 2 2 cm 7 8 j T va Screw Retainer 2 Saa a Height Xo M rae a g SHOWN ACTUAL SIZE y Adjuster qe ep Adjuster e Insert a 10 x 2 2 cm 7 8 black screw into the screw retainer and tighten e Repeat this procedure to fasten the other end of the base with the remaining screw retainer and 10 x 2 2 cm 7 8 black screw Fit the frame front legs into t
6. he base tray latches onto the pegs on the back of the high chair frame Pull Frame Release Latch e With the legs all the way open lower the seat to position 1 the lowest position e Pull the frame release latches forward and push the rear legs toward the front legs 15 Fisher Price Inc a subsidiary of Mattel Inc East Aurora New York 14052 U S A 2003 Mattel Inc All Rights Reserved and designate U S trademarks of Mattel Inc Printed in China B8866a 0726
7. he other base e Fit a screw retainer over a hole in the base TA Oj Bottom AN Z _ 7 q N a at Tube Ends SS o Hint The 10 x 2 2 cm 7 s black screws may have been 1 3 assembled to the screw retainers Back and A Bottom View e From the back and bottom of the assembly insert a 8 x 1 9 cm 3 4 screw through both seat height adjusters and the ends of the seat bottom tube e Tighten the screws 7 Assembly Pad Front View Elastic Loops Back and Bottom View e Lift the assembly upright e From the front of the assembly place the pad onto the seat Lift the bottom of the pad Insert the two elastic loops on the pad through the holes in the seat bottom e From the back and bottom of the seat hook the elastic loops to the tabs on the seat 8 Insert the crotch belt through the slot in the pad Make sure the crotch belt is not twisted Shoulder Portion e Fold the top of the pad down e Remove the shoulder portion of the waist shoulder belts by feeding them through the slots in the seat back Assembly Upper Shoulder Belt Slots Shoulder Portion Lower Shoulder Belt Slots Lift the top of the pad e Thread the waist shoulder belts through the bottom slots in the back of the seat pad e Insert the shoulder portion of the shoulder waist belt through the slots in the pad and seat back Use the lower shoulde
8. l the tray base towards you and remove 13 Adjusting the Seat A WARNING Prevent serious injury or death from falls or sliding out It is recommended that the high chair be used in the upright position only by children capable of sitting upright unassisted Hint Adjust the seat height to any of seven positions Seat Height Adjuster To adjust the seat height e Press the levers on both seat height adjusters and lift or lower the seat to the desired height e Make sure both sides of the seat are adjusted to the same height Push the seat bottom to be sure the seat is locked in place Note Make sure there is nothing obstructing the seat height adjusters To adjust the seat angle e Squeeze the seat back e Push the seat back to be A PEN idan wo 2 A Hint Adjust the seat angle to any of three positions Upright Semi Recline or Recline Upright Semi Recline Recline handle and push the seat back forward or pull it backwards to the desired position sure it is latched in position Storage Care e The pad toy frame and base tray may be wiped clean using a mild cleaning solution and a damp cloth Do not immerse the base tray e The food trays are dishwasher safe Simply remove the food tray from the base tray and place in your dishwasher IMPORTANT Never use this product without the restraint system Replace the waist shoulder belts and crotch belt Fit the holes on t
9. r belt slots for a smaller baby Use the upper shoulder belt slots for a larger baby Fit the top of the pad over the seat back Fold the bottom edge of the pad under the edge of the seat bottom to fasten Assembly Securing Your Child IMPORTANT Handle Pad Strap e Before each use inspect this product for damaged hardware loose joints missing parts or sharp edges DO NOT use if any parts are missing damaged or broken Contact Mattel for Elastic i Loop replacement parts and instructions if needed Never substitute parts e Place the high chair on a level stable surface away from electrical flexes Be sure to keep electrical flexes out of child s reach yi EN WARNING Elastic Loop Tab Prevent serious injury or death and adjusted 19 he zeng Erai P i IO Waist Shoulder Waist Shoulder From behind the seat be sure the shoulder portion of the Belt Belt waist shoulder belts are secure in the seat back slots Fit the pad strap through the handle and press it to the fastener on the back of the seat e Hook the elastic loops on each side of the pad onto the tabs in the seat back I from falls or sliding out al The child should at all times wear a safety harness correctly fitted Back View mm Assembly is now complete Crotch e Place your child in the seat Position the crotch belt between your child s legs e Fasten both waist shoulder belts to each side of th
10. through make sure you pull on it to be sure it is securely fastened the desired shoulder belt slots in the headrest pad seat pad and the seat back Pull on the belts to be sure they are secure in the seat back 11 Using the Trays Hint The base tray can be adjusted for your child s comfort two ways see steps 7 and 8 A WARNING Prevent serious injury or death from falls or sliding out The tray is not designed to hold the child in the chair Base Tray s Fai Release Bar e While pushing the release bar on the front of the base tray adjust the base tray forward or backward Fit the base tray onto the seat armrests Push down until the base tray snaps into place Hint Before use thoroughly wash all parts the trays that may contact food e While squeezing the latches underneath the base tray adjust the base tray forward or backward 12 Using the Trays Hint The base tray can be removed two ways see steps 9 and 10 Food Tray oT pranan Ss Sew ew wn nnn ee r k Base Tray lt a lt ene eee r Squeeze Latch Squeeze Fit the food tray into the base tray as shown Hint Before use thoroughly wash all parts the trays that may contact food e Squeeze one or both of the latches underneath the base tray and lift e While pushing the release bar on the front of the base tray pul
Download Pdf Manuals
Related Search