Fisher & Paykel OB76 User's Manual
Contents
1. 688 757 608 675 718 570 38 530 724 762 681 693 575 Note If installing a cooktop above the oven ensure adequate clearance is provided for the cooktop as per the cooktop manufacturer s instructions G PRODUCT AND CABINETRY DIMENSIONS Double oven models 2 5mm _ Flush install 16 20 mm 16 20 mm dE E 25mm Ensure the cavity is completely sealed with no gaps Product and cabinetry dimensions mm overall height of product overall width of product overall depth of product without handle height of chassis width of chassis depth of chassis depth of oven frame and control panel excl knobs TO TMmMOd 0w0 gt depth of oven doors open measured from front of oven frame l minimum inside width of cavity l overall width of cabinetry J inside height of cavity J overall height of cabinetry K _ minimum inside depth of cavity 4 CABINETRY PREPARATION Double models featured for illustration purposes only ELECTRICAL CONNECTION Proud install Flush install Important Ensure you have created a 38 mm recess in cabinetry if flush installing AY OB76 Single Max current draw 19 4A Max load 4 6 kW OB76 Double Max current draw 38 3 A Max load 9 2 kW We recommend that the outlet for the power supply cable is located in the right rear corner of the cabinet cavity This allows the power supply2. Installation instructions Aerotech oven OB76 models Fisher amp Paykel innovative living Important SAVE THESE INSTRUCTIONS The models shown in this document may not be available in all markets and are subject to change at any time For current details about model and specification availability in your country please go to our website www fisherpaykel com or contact your local Fisher amp Paykel dealer 1 SAFETY AND WARNINGS A WARNING Very Heavy A WARNING Electrical hazard Always disconnect the oven from the mains electricity supply before carrying out any maintenance operations or repairs Do not attempt to lift this product unassisted Lifting unassisted may cause serious injury Failure to do so may result in electrical shock or death SINGLE OVEN MODELS A WARNING Cut hazard Take care panel edges are sharp Failure to use caution could result in injury or cuts Impor tant safe ety preca utions To avoid hazard follow these instructions carefully before installing or using this product Please make this information available to the person installing the product as it could reduce your installation costs This oven is to be installed and connected to the electricity supply only by an authorised person If the installation requires alterations to the domestic electrical system call a qualified electrician The electrician should also check that the socket cable section is
3. cable to sit inside the rear chamfered corner of the oven and prevents it being jammed between the cabinet wall and the rear of the oven A Important Ensure you remove the long trim from the packaging 7 SECURE THE OVEN TO THE CABINETRY AND REFIT THE DOOR S Ensure supplied spacer is fitted between oven and cabinetry Take care not to damage the lower trim of the oven FLUSH INSTALLATION ONLY REPLACE THE LOWER TRI SS gt N B i Unscrew and remove the installed lower trim Replace with the supplied long trim Please turn over gt 9 FINAL CHECKLIST OO O lt OO Make sure the appliance is level and securely fitted to the cabinetry and both oven doors open and close freely Make sure all the internal packaging has been removed from the oven cavity Make sure all oven vents and openings are clear and are free of any obstruction damage Important Failure to make sure all oven vents are unobstructed may result in poor product performance Turn the power to the oven on The clock should light up and flash 12 00pm Set the clock to the current time 1 Rotate the Push To A button until the correct time is showing 2 Press the CLOCK button to set the time or wait eight seconds and it will set automatically Turn t
4. he oven function knob to Bake and the oven temperature knob to 180 C Air should blow out of the vent at the bottom of the oven Inside the oven cavity all three oven lights should come on After five minutes open the oven door and the air inside should feel warm and the top element should be glowing red Turn both the oven function knob and oven temperature knob back to OFF and repeat for the other oven if the appliance is a double model TROUBLESHOOTING If the appliance is not functioning correctly after installation check the following Check that the circuit breaker has not tripped or the fuse blown Make sure that the electrical connections have been correctly made Make sure that power is being supplied to the oven Make sure the voltage is correct across all phases If a problem occurs consult the Troubleshooting section of the User Guide If after checking these points you still need assistance please refer to the OOOOOO Service amp Warranty book for warranty details and your nearest Authorised Service Centre or contact us through our website www fisherpaykel com 599510A NZAU 03 08
5. suitable for the electricity drawn by the oven The oven must be earthed To connect the oven to the mains do not use adapters reducers or branching devices as they can cause overheating and burning Installation must comply with your local building and electricity regulations Failure to install the oven correctly could invalidate any warranty or liability claims Before you install the oven please make sure that The oven will rest on a flat surface that can support its weight The benchtop and oven cavity are square and level and are the required dimensions The height from the floor suits the user The oven door can open fully without obstruction a suitable disconnection switch is incorporated in the permanent wiring mounted and positioned to comply with the local wiring rules and regulations A means of disconnection with at least a 3 mm air gap contact separation in all poles must be incorporated into the fixed wiring in accordance with the wiring rules unless the local wiring rules allow for the following variation A means of disconnection from the supply having and air gap separation in all active phase conductors must be incorporated into the fixed wiring the electrician provides sufficient free length of power supply cable to reach from the bottom rear of the cavity to at least 1 5 metres in front of the bottom edge of the opening The cable may enter the cavity from the side top or bottom but top entry must be a
6. t the rear of the cavity When you install the oven Do not seal the oven into the cabinetry with silicone or glue This makes future servicing difficult Fisher amp Paykel will not cover the costs of removing the oven or of damage caused by this removal Use the supplied screws and spacers to secure the oven to the cabinetry Do not over tighten the screws Do not stand on the door or place heavy objects on it Do not lift the oven by the door handle Take extra care not to damage the lower trim of the oven Use easy to clean finishes for the wall surfaces surrounding the oven so that cooking fume staining resulting from using the oven is easy to remove 2 PRODUCT AND CABINETRY DIMENSIONS Single oven models 2 5mm Installation diagrams for illustration purposes only Proud install 16 20 mm Flush install E p 1116 20 mm UM 2 5 mm Ensure the cavity is completely sealed with no gaps Product and cabinetry dimensions mm overall height of product overall width of product overall depth of product without handle height of chassis width of chassis depth of chassis depth of oven frame and control panel excl knobs depth of oven door open measured from front of oven frame TITO TM ON 8 S minimum inside width of cavity overall width of cabinetry inside height of cavity overall height of cabinetry A minimum inside depth of cavity sjepow S 9 90
Download Pdf Manuals
Related Search