Fisher & Paykel E522BLE5 Instruction Manual
Contents
1. Plug 880618 Ventilation Grill Not part of the kit order separately recommended for integration of 790 wide models Ventilation grill Not part of the Kit order separately 873917 Internal dimensions Model 525 Width A Depth B Height C PC FC Centre line D H Drawer E P120 RF120 600 600 840 C190 150 RF190 RF150 600 600 1228 C170T E1691 RF169T 600 600 1228 811 270 E210 RE270 RF210 600 600 1616 E2497 RE249T 600 600 1616 1200 E240B RF240B 600 600 1616 811 Model 635 E3317 RF331T 735 730 1446 D E373 C373 E308 735 730 1446 E381T RF381T 733 730 1616 1141 E372B RF372B 735 730 1616 652 F411T RF411T 735 730 1716 1240 402B RF402B 739 730 1716 652 E415H 735 730 1716 1240 480 450 C450 E388 735 730 1716 Model 680 E413T 780 730 1616 1141 E406B 780 730 1616 652 E440T 780 730 1716 1240 F442B 780 730 1716 652 Model 790 E521T 890 730 1716 1240 E522B 890 35 32 730 283 4 1716 679 16 652 251 16 Internal Dimensions width of the built in cabinet is as follows 790 680 635 models Cabinet internal width Product width 790 680 or 635 80mm 3 s hinge side and 20mm 3 4 door open side 525 models Cabinet internal width 600mm Product width 525mm 55mm hinge side and 20mm door open side Only 90 hing2. 14 Drawer outer panel as viewed from the back b gt Attach the 4 x angle brackets to the back of the outer drawer panel Assembly instructions for H drawer built in kits e The H drawer of this type of refrigerator is attached to the outer door panel of the built in cabinet by means of four angle brackets attached to the back of the outer drawer front 1 Fit the Refrigerator as previously instructed into the built in cabinet and attach the other door 2 Remove the H Drawer handle from the top of the H Drawer and discard Fit the endcap outer and end cap blanks provided in the H Drawer kit 3 Take and mark the position of the outer drawer front drawer panel against the H Drawer itself note the clearance needed between the Drawer front panel and the door above Masking tape is ideal to place over the area to be marked The H Drawer can be removed from the refrigerator completely by pulling it out to it stops and then lifting it up and pulling forward 4 Place and mark drawer front mounting brackets at each corner of the H Drawer position 5 Attach the mounting bracket to the back of the outer door panel Note Check the length of the mounting screw E so that ie doesnt go right through the outer drawer panel 6 The outer drawer panel can now be attached to the H Drawer itself by screwing through the side of the H D
3. all This will set a 20mm 3 4 gap between cupboard and refrigerator Adjust the product so it is parallel to the cabinet front to back and side to side This is obtained by the adjustment of the front levelling feet WARNING Please be advised that adjustment of glass shelves is not possible once the refrigerator has been integrated 10 DOUBLE DOOR REFRIGERATOR SINGLE DOOR REFRIGERATOR Diagram 8 Attach Slide bracket to Refrigerator Doors Attach the slide bracket to the side of the door opposite to the hinges 100mm 4 in from the edge On a two door refrigerator use one slide bracket per door If integrating a 790 model we recommend using 2 slide brackets per door one near the bottom of the door amp one near the top of the door to evenly distribute the weight The brackets should be attached to the opening side of the doors near the refrigerator and freezer compartments On a single door refrigerator use one slide bracket at each end of the door Screw brackets firmly into the steel door face using countersunk screw C Attach Slide Bracket to Cupboard Door a Open both cupboard and refrigerator door to 110 degrees 525 Compact models to 90 b Put slide bracket in retainer 120mm 43 4 approx past refrigerator door diagram 9 c Check that screw A supplied with kit will not penetrate front surface of cup board door diagram 10 d Screw slide bracket level into the cupboard door us
4. customer CAV Gog Integral Kit Instructions For Fisher amp Paykel Cabinet widths of 525 635 680 790 mm wide For curved door Models Series B C D amp G Manual 814980 Updated August 2008 IMPORTANT If your refrigerator has this type of front roller assembly as shown in diagram 1 then these are the INCORRECT Built in Kit instructions and dimensions you are following Please use Built in Kit instructions 873918 Pre June 1995 Post June 1995 Kit Part Number 874561 Kit Part Number 874560 H Drawer Kit 876811 H Drawer Kit 876811 1985 G H A J K L M P Q R series to June 1995 1995 R series July onward Curved Door Models If your refrigerator has this type of front roller assembly as shown in diagram 2 then these are the CORRECT instructions Kit Part Number 814990 H Drawer Kit 880800 1998 B series October onward Part Quantity Parts supplied with Built In kit Part No 814990 Description Part no 4 Rail slide 880791 Bracket slide 880792 Foot Integration 880793 Cap Elliptical for foot integration 880794 Spacers 20mm 880795 Screw A 8X 3 4 CSK POSI Screw B 48X30 CSK POSI 880796 880797 Screw C 8X40 CSK POSI 880798 Screw D 8X 2 PAN PH 900373 Endcap Blank RH 883715 Endcap Blank LH 883716
5. es are to be used See hinging section pg 5 For height dimensions of the doors don t forget to take into account the thickness of the material used in the floor and roof of the built in cabinet as the dimensions stated are all internal Note All dimensions shown are internal Installation dimensions Measure from surface the refrigerator rests on part No 873917 Diagram 3 For Insert Doors add 30mm 2 to A and B Cabinet Construction IMPORTANT NOTICE For a refrigerator to function to its optimum standard it requires a certain amount of air clearance around the cabinet With integration the cabinet is essentially sealed up As a result the products energy temperature and or basic performance could be affected as compared to a freestanding product If there are any issues with the products performance due to integration this is at the customers risk This diagram depicts the use of a ventilation grill We recommend the use of this grill when integrating 790 wide models This grill is not included in this kit and can be ordered as Part 873917 Hinges Illustrated below are some of the types of hinging that can be used 790 680 amp 635 Models It is recommended that 110 hinges having a low profile are used either full or half overlay such as the GRASS brand We recommend the use of hinges that can carry a high load especially when integrating 790 models For 525 Models we reco
6. handle Curved Door Models 1 Remove door end cap to expose the door handle plate 2 Remove screw which holds handle bracket as shown in Photo A 3 Remove plate Photo B pull handle away from door 4 Pull bottom of handle from door Elegance Inox Photo A 7 Photo B Flat door models Remove small screw from underneath of Designer the handle Refer Photo C Use a 2 75mm Allen Key Once screws have been removed handle bosses can be removed from the door Flat doors Designer 2 Handles Note The designer 2 Handle has a large handle end therefore uses a larger grub screw 1 Using a 2 75mm Allen key remove the grub screw refer Photo D from the underneath of the handles 2 Remove the handles 3 Remove handle bosses Photo D Tilt the product back and remove the levelling foot circular base insert from the front levelling feet a small flat blade screw driver can be used Lift the product into the cabinet 100mm 4 to Gasket face Lift the front edge of the product and slide the integration foot under the levelling foot Push the product back to allow the outer cabinet door to close This will be approximately 100mm 4 from the front edge of the built in cabinet to the gasket face of the refrigerator Align Refrigerator in Cupboard Slide the product toward the opening side of the cupboard The integrated foot should touch the cupboard w
7. ing screw A supplied with the kit e Check slide mechanism does not bind through swing of door f Repeat for second bracket Screw slide bracket in level IMPORTANT nee 120mm 48 4 Ensure that refrigerator doors are able to close fully and seal around the flexible gasket on the refrigerator freezer This is to prevent air leaks and icing problems Complete Installation a If installing a H model with a roll out humidity drawer then fit the outer door panel following the instructions in the next section b Otherwise complete the installation by screwing the foot integration into position using screw D supplied with the kit and the cap elliptical to cover the screws 11 12 Humidity Drawer Installation lt Measure from surface the refrigerator rests on Dimensions If 0 overlay doors are used add 30mm to dimension A and P Specification subject to change without notice Humidity Drawer Installation Additional humidity drawer kit Part No 880800 Part Quantity Description Part no h 4 Bracket 880801 g 12 Screw E 6X 1 2 PAN PH SP0008 2S 1 Endcap Blank RH white 883715 v 1 Endcap Blank LH white 883716 DOO est 1 Endcap Outer 635 white 883670 Diagram 12 Diagram 13 Humidity Drawer Installation
8. mmend only 90 hinges to allow fitment in 600 modular units Full overlay Half overlay Door closed Toas noa u do 100q Butt hinge u do 100q u do 100q Door closed Door closed Must add 30mm 2 to dimension A amp B 1 Prepare Refrigerator for Installation a Check that the internal cupboard dimensions are correct see page 3 we Unpack refrigerator protecting the floor and or paint work from damage Check that refrigerator door is hinged on desired side Refer to use amp care booklet for instructions to change hinge side Remove the door handles on models 635 680 amp 790 Fit the door end cap blank to the corner of the door Fit small plugs to the screw holes left when the door handle was removed Using screw B attach spacers to the side of the built in cabinet on the side without hinges They should be positioned approximately 100mm 4 from the top front 150mm 6 from the front edge and 75mm 3 rear corners of the refrigerator cabinet These spacers along with the foot integration bracket maintain an even gap of 20mm 3 4 between the cupboard and the refrigerator side How To Remove Refrigeration Handles Tasman Models 1 There are 3 screws on the PC door With Plastic Handles and two on the FC door that hold on the Tasman handles 2 Remove cap covering screws and remove screws as shown below 3 Remove
9. rawer 7 Adjustment in out is made by the slots in the brackets IMPORTANT Ensure that refrigerator doors are able to close fully and seal around the flexible gasket on the refrigerator freezer This is to prevent icing problems Humidity Drawer Installation
Download Pdf Manuals
Related Search