Fisher & Paykel DS602I User's Manual
Contents
1. supplied with the accessories is fitted Hose coupling must be tightened a further half turn after seal contact 2 2 3 If required the Drain Hose may be trimmed to a suitable length 2 2 4 If an air break option is not chosen then the Drain Hose Support must be used and positioned at least 13 4 350mm above the base of the DishDrawer to prevent siphoning of the water during the wash program See Step 1 4 Electrical Plumbing amp Drainage Information 2 2 5 When using a standpipe option hose should not extend further than 2 50mm down the standpipe in order to prevent siphoning 2 2 6 If required trim the Single Connector to the size which matches the waste tee or air break to be used There are ribs provided to guide cutting When using the Single Connector the hose should be pushed in firmly 5 clicks Remember to slip the Wire Clip over the Drain Hose before connecting to the Single Connector The supplied Wire Clip should be installed between the two positioning ribs on the Single Connector 2 2 7 Attach Single Connector to waste tee Ensure snug fit using the supplied hose clamp Ensure there is a power outlet in reach of the supplied flex If there is not a suitable outlet available then have one installed by a qualified electrician DO NOT modify the power plug supplied with the DishDrawer or use an extension cord adaptor plug or multiple outlet box 2 2 8 Alternativel2. 0 kpa Empty 62lb 28kg Prefinished May require the electronics to be Electrical 110 120VAC re programmed by a Service Person 3 pin socket outlet at the time of installation Drying Residual Heat amp Fan Assisted Recommended Hot 140 F 60 C Max Maximum 139 p s i 960 kpa Minimum 4 3 p s i 30 kpa Water Connection Water Pressure SECTION 1 WARNING Before installing the DishDrawer remove the house fuse or open the circuit breaker Ensure all water connections are turned OFF warninc The DishDrawer MUST be installed to allow for future removal from the enclosure if service is required Page DS_02 IMPORTANT Where the DishDrawer is in an under counter situation i e built into a kitchen unit it is recommended that bare wood surrounding the DishDrawer is sealed with an oil based paint or polyurethane to prevent possible steam damage 1 IMPORTANT If mounting the DishDrawer near the bottom of the cabinet ensure there is adequate room underneath the supporting cabinet to tighten bolts 1 IMPORTANT Ensure the cavity sides are plumb vertical as this will assist with leveling the DishDrawer 1 IMPORTANT Ensure the Services Hole is as close as possible to the rear corner of the cabinet The hole can be located on either side depending on the location of the services 1 IMPORTANT On corner installations ensure that there is a gap of 2 50mm
3. 232mm pagea drilling out holes for 6 a Drawer Front Mounting 160mm Panel 13 5 746 1475mm 171 5mm SS a eaution Ensure the drill does not damage the face of the Drawer Front These dimensions are important to ensure a 4 6mm airflow gap Page DS_14 SECTION 5 l a IMPORTANT To avoid electric shocks and damage to electronic components the integrated badge should be disconnected from the E DishDrawer when changing the badge CHE enclosure R A T E D P Button Badge Connection Runner Page DS_15 INTEGRATED DRAWER FRONT INSTALLATION STEP 5 1 CHANGING THE INTEGRATED BADGE ENCLOSURE There are several different colored Integrated badges to choose from They include black chrome satin amp brass Two color options are provided with your machine other options are available from your local Dealer There are five parts to the Integrated Badge Assembly They are as follows Integrated Badge Button Badge Light Pipe Electronics Board Badge Cover Wires oe ee N a STEP 5 2 DISASSEMBLING THE INTEGRATED BADGE ASSEMBLY 5 2 1 Remove Badge Cover from the Integrated Badge At the back of the Integrated Badge slide the Badge Cover away from the wire terminals 5 2 2 Remove Electronics Board Gently hold the wires to remove the Electronics Board Care should be taken not to handle the front or ba
4. A ff aAA FisherSPaykel MA Aaa eee Installation Instructions USA DishDrawer DS602 Prefinished DS6021 Integrated Models DS602 DS602I Part No 599066 D Section Section Section Section Section Section Section ee ee ee ae ee oe S aubkwRo 2 2 2 Single DishDrawer Table of Contents General Information Preparation Product Specifications amp Cavity Dimensions Options for Installing Multiple Products Electrical Plumbing amp Drainage Information Product Parts Additional Product Parts for Integrated DishDrawer Fitting the DishDrawer DishDrawer Mounting Hole Locations Connecting the Services Flexible Extrusion Attachment for 24 Cavity Inserting DishDrawer Into Cavity Information for Cabinet Maker for Integrated DishDrawer Integrated Drawer Front Dimensions Integrated Drawer Front Installation Changing the Integrated Badge Enclosure Disassembling the Integrated Badge Assembly Assembling the Integrated Badge Fitting the Badge Handle amp Mounting Panel to the Drawer Front Fitting the Drawer Front to the DishDrawer Final Fitting For Single DishDrawer Final Checks Installation Wet Test Troubleshooting Page DS_01 GENERAL INFORMATION STEP 1 1 PREPARATION NOTE TO THE INSTALLER m Be sure to leave these instructions with the Customer E Ensure this appliance is properly grounded NOTE TO THE CONSUMER m Keep these Installation Instructions with your Use a
5. CAVITY SECTION 3 Jwarnine DO NOT push against the middle of the drawer 3 1 1 Position product to suit joinery ensuring hoses are not kinked or cut DishDrawer Cabinet Align handle lt lt curve with lt cabinet front 3Ja2 esm 1 IMPORTANT Make sure the inlet and drain hose and main flex are not restricted or damaged by carefully pulling them through the Services Hole as the DishDrawer is being pushed back into the cavity Jwarnine The DishDrawer should not support any part of the kitchen cabinetry 3 1 2 Insert M8 bolts and washers through holes in shelf DishDrawer 3 1 3 Ensure product is correctly positioned and Counter top aligned before tightening Refer to Step 7 1 Installation Wet DishDrawer front Test Page DS_10 SECTION 4 1 IMPORTANT Recommended Drawer Front thickness for Integrated product is 5 s to 3 4 16mm 18mm 4 1 1 Fronts Use the following diagrams to work out the dimensions for the Integrated Panels for Drawer Width of Cavity l 3 3 732 732 2 5mm 2 5mm Minimum Minimum INFORMATION FOR CABINET MAKER FOR INTEGRATED DISHDRAWER STEP 4 1 INTEGRATED DRAWER FRONT DIMENSIONS 1 IMPORTANT Bench Top Drawer Front material must be suitable for damp conditions or adequately sealed to withstand moisture
6. Cabinetry Height from Top of Doors to Base Additional protection can be provided by using a Moisture Resistant Board 1 IMPORTANT Allow for any obstructions at the top of the cavity when allowing for space between the countertop and DishDrawer Front View of DishDrawer Drawer Front Width Width of Cavity 3 u ean 732 732 25mm _ 2 5mm l l Minimum Minimum Note The minimum Drawer Front Width is 234g 595mm Minimum Drawer Front Height from Top B Height Ao Doors to Base Ei Note The minimum Drawer Front Height is 1540 390mm Minimum Page DS_11 1 IMPORTANT A minimum clearance of 3 30 2 5mm must be maintained between the Drawer Front and existing cabinetry except between the underside of the Drawer Front and the 3 shelf where a 4 6mm BECH clearance is needed for Minimum product venting Bench Top Drawer Front gt 410mm Minimum Drawer Front Air Flow Chamfer Chamfer the back of the Drawer Front Panel at the bottom as shown to enhance air flow 16 Drawer front Side View of DishDrawer J 16 18mm 4 1 2 Use the following diagrams if installing the DishDrawer at floor level Bench TP SSS A Cabinetry Cabinetry Drawer Front 4 4 Top of 6mm Toe Kick Front View of DishDrawer Side View of DishDrawer Page DS_12 1 IMPORTANT 4 1 3 Cont
7. PLUMBING WATER SUPPLY a The water connection is to be made to a hot water supply only Ensure the water temperature is not greater than 140 F 60 C A readily accessible shut off valve must be installed in the supply pipe c The water supply pressure is to be between 4 3 p s i minimum and 139 p s i maximum d The inlet supply hose must be connected to the water supply using a s compression type water supply fitting e Ensure sealing washer supplied with connection hose is fitted PLUMBING DRAINAGE OPTIONS Option 1 D gt WASTE WASTE DISPOSAL UNIT gt lt HOT WATER a gt WASTE 8 200mm MINIMUM TO CONSTRAINING SURFACE Option 2 DishDrawer amp Waste Disposal DRAIN HOSE Ye ses SUPPORT a N 0 gt WASTE WASTE DISPOSAL D lt HOT WATER 8 200mm MINIMUM TO CONSTRAINING SURFACE Option 3 DishDrawer With Air Break WASTE DISPOSAL D lt HOT WATER 8 200mm MINIMUM TO CONSTRAINING SURFACE Note DS602 Prefinished Model is shown There is no variation in plumbing between DS602 Prefinished Model and DS6021 Integrated Model Options 1 and 2 are the preferred options 1 WARNING Improper connection of the equipment grounding conductor can result in a risk of electric shock Check with a qualified electrician or service representative if you are in doubt as to whether the appl
8. aw the cavity center line on the supporting cabinetry 2 1 2 Center Template in cavity using V notch on the front of the Template 2 1 3 Align front of Template to suit surround of cabinetry 2 1 4 Mark and drill four 15 32 9 6 12mm 14mm diameter holes as described on Template SECTION 2 eak Ensure the cavity is at least 227 s 580mm deep 1 IMPORTANT For Integrated product with door thickness other than 18mm the Template position must be adjusted forward or back to allow for this difference Page DS_06 WARNING STEP 2 2 CONNECTING THE SERVICES Ensure the edges of the Service Hole are smooth or covered See Step 1 2 Product Specifications amp Cavity Dimensions If the Services Hole is through a metal partition the hole must be protected with the Edge Protector provided 1 Jwarninc DO NOT adjust the length of the Inlet Hose TIP Turn the water valve ON to check for any leaks before pushing the DishDrawer back into its cavity 1 WARNING Attach the Drain Hose Support to the cabinet cabinetry to prevent siphoning and to keep the Drain Hose from kinking Page DS_07 2 2 1 Feed the Power Cord Inlet Hose and Drain Hose through the Services Hole Position the DishDrawer in front of the opening 2 2 2 Connect the Inlet Hose to the HOT WATER SUPPLY Ensure the sealing washer
9. ck of the Electronics Board or touch inside the wire terminals 5 2 3 Remove the Light Pipe Gently tap the Integrated Badge upside down on a hard surface until the Light Pipe comes away or insert a pen or pencil into the front side of the Integrated Badge to either one of the two small holes 5 2 4 Once you have removed the Electronics Board Badge Cover and Light Pipe you can assemble the electronics board into a badge of another color STEP 5 3 ASSEMBLING THE INTEGRATED BADGE 5 3 1 Insert the Button Badge into the back of the Integrated Badge Do not break any of the buttons away from the Connection Runner 5 3 2 Insert the Light Pipe into the Integrated Badge Insert the Light Pipe with the circular ends into the small holes 5 3 3 Insert the Electronics Board with care behind the Button Badge When installing the Electronics Board handle only the wires and do not touch the face or back of the Electronics Board or inside the wire terminals 5 3 4 Slide the Badge Cover into the slot on top of the Integrated Badge STEP 5 4 FITTING THE BADGE HANDLE amp MOUNTING WARNING PANEL TO THE DRAWER FRONT Care should be taken in the following steps 1 CAUTION Take care not to damage front surface of panel 5 4 1 Remove Drawer Front Mounting Panel by withdrawing pins from sides of drawers using long nosed pliers 5 4 2 Slide Mounting Panel off in a downwards and outwards motion Ensure al
10. iance is properly grounded Do not modify the plug provided with the appliance if it will not fit the outlet have a proper outlet installed by a qualified electrician 1 WARNING The Drain Hose Support must be at least 13 350mm above the base of the DishDrawer to prevent siphoning of the water during the wash cycle It is recommended that the Drain Hose Support is secured in place using the screw tab Ensure that the drain hoses are fully extended Page DS_04 Tools Needed To STEP 1 5 PRODUCT PARTS Install DishDrawer e Wooden Chopping Board e Level e Safety Glasses Utility Knife TEMPLATE Pencil Drill amp Drill Bits 3 32 ie amp 1 32 2 5mm 12mm 14mm Sandpaper Tape Measure Square Ruler Phillips Screwdriver Pliers Adjustable Wrenches x2 7 32 6mm Allen Key Integrated Models Router Integrated Models e Jigsaw Integrated Models ALIGN EDGE WITH FRONT OF CUPBOARD DOOR OR DRAWER e e Template Single 1 Single Connector 1 Drain Hose Support 1 Edge Protector 1 Screw 1 9 Flexible Extrusion 2 Wire Clip 1 Solderless Lug amp Washer 1 MB Bolts 4 Inlet Hose Washer 1 Washers 4 Hose Clamp 1 STEP 1 6 ADDITIONAL PRODUCT PARTS FOR INTEGRATED DISHDRAWER Mounting Bracket Nuts 4 Seal 1 Door Screws 4 Badge Kit 2 Page DS_05 FITTING THE DISHDRAWER STEP 2 1 DISHDRAWER MOUNTING HOLE LOCATIONS 2 1 1 Dr
11. ion 5 5 4 Ensure the slide hooks on slide are as far forward as possible as shown then insert pins to lock in place ensuring that the rib on the pin is vertical Check fit of the Drawer Front and adjust if required FINAL FITTING FOR SINGLE DISHDRAWER SECTION 6 6 1 1 Check final fit of DishDrawer in cavity Counter top DishDrawer front 6 1 2 Tighten M8 bolts DishDrawer Page DS_18 SECTION 7 Page DS_19 FINAL CHECKS STEP 7 1 INSTALLATION WET TEST Ensure product is level securely fastened to the floor and opens and closes freely e Ensure inlet hose to faucet connection is tightened to specification drilled out and the drain connection made correctly e Plug in and turn ON the power and water supply The DishDrawer should beep and light up Oo UO OU 3 Ensure any knockouts or plugs in the drain connection have been Open the drawers of the DishDrawer and check operation of Secondary Control Panel and check sprayarm is in place and free to rotate e Select Rinse program on the Secondary Control Panel and close the drawer e Start the Program by pressing the Start Pause button for water leakage Ensure machine has run and drained correctly OO OU g 7 8 After the program has finished check underneath the DishDrawer Check water supply and drainage connection for leakage Water underneath DishDrawer check the hose connections a
12. l cuts are straight and care is taken to avoid damage to the Drawer Front 5 4 3 Using an Allen Key screw in Mounting Bracket Nuts Remove Burrs Screw in flush with back surface 1 CAUTION Overtightening will damage the Drawer Front 5 4 4 Fit the Door Mounting Panels using the screws supplied 5 4 5 Feed wires through to the back and press badge into hole If needed adhere badge to Drawer Front with a glue or silicon sealant 5 4 6 Fit the customer supplied handle Refer to Step 4 1 3 Control Badge Position Page DS_16 Use a small amount of liquid soap along the lip of the seal to aid the Drawer Front to slide on easily against the seal 1 CAUTION The rubber seal between the Drawer and Drawer Front must be kept in place 1 WARNING The Electronics Board is an electrostatic sensitive device Ensure you are adequately grounded when connecting or disconnecting the badge by wearing a grounding strap or by grounding yourself to the DishDrawer WARNING Ensure the product is not plugged in View of Slide Hooks CORRECT INCORRECT Page DS_17 STEP 5 5 FITTING THE DRAWER FRONT TO THE DISHDRAWER Drawer front 5 5 1 Fit seal to Drawer 5 5 2 Plug the grounding wire into the panel Connect badge wires to integrated badge port on Electronics Board 5 5 3 Fit Drawer Front by sliding in an upwards and inwards mot
13. minimum between the adjacent cabinetry and sides of drawers m DishDrawer STEP 1 3 OPTIONS FOR INSTALLING MULTIPLE PRODUCTS Integrated or Prefinished Integrated or Prefinished di di Iho 2 5mm Spacing 1 aje gt ke fe a 2 5mm Spacing Integrated Models Only F A 345 2 5mm Spacing Ak STEP 1 4 ELECTRICAL PLUMBING amp DRAINAGE INFORMATION EEE ELECTRICAL Care should be exercised when the appliance is installed or removed to reduce the likelihood of damage to the power supply cord If the power supply cord is damaged it must be replaced by the Manufacturer it s Service Agent or a similarly qualified person in order to avoid a hazard The power supply receptacle for the appliance should be installed in a cabinet or on a wall adjacent to the under counter space in which the appliance is to be installed The power supply receptacle should be positioned between 6 and 18 150mm and 450mm from the cabinet opening of the DishDrawer GROUNDING INSTRUCTIONS This appliance must be grounded In the event of malfunction or breakdown grounding will reduce the risk of electric shock by providing a path of least resistance for electric current This appliance is equipped with a cord having an equipment grounding conductor and a grounding plug The plug must be plugged into an appropriate outlet that is installed and grounded in accordance with all local Codes amp Ordinances
14. mp Care Manual for future reference IMPORTANT E Read these Instructions completely and carefully m Observe all governing Codes and Ordinances WARNING These Instructions are intended as a guide only It is the responsibility of the plumber and electrician to ensure that each installation complies with all Codes and Ordinances Installation of this DishDrawer requires basic mechanical and electrical skills The installer is responsible for the DishDrawer installation Improper installation is not covered under the Express Warranty Form IMPORTANT m At the completion of the DishDrawer installation the Installer must perform Final Checks as per Section 7 of these Installation Instructions m Ensure the DishDrawer enclosure is prepared for installation E Remove all packaging and materials supplied with the DishDrawer m If you have any questions concerning the installation of this DishDrawer contact Fisher amp Paykel Customer Care Centre TOLL FREE 1 888 9 FNP USA TOLL FREE 1 888 9 367 872 Fax 949 829 8699 27 Hubble Irvine CA 92618 USA WWW FISHERPAYKEL COM STEP 1 2 PRODUCT SPECIFICATIONS amp CAVITY DIMENSIONS CABINETRY DIMENSIONS Height 16 30 410mm Width 23 600mm Depth 22 580mm Service Hole 115 38mm Service Hole Qj 146 2276 80mm sae Curvature E q 237e 595mm 16 Tho 407mm 520mm Drawer Open Weight Full 931b 42kg Prefinished Water pPreSSUTE below 7 psi 5
15. nd hose for leaks 2 Water around water supply and drainage connections check connections existing plumbing and hoses for leaks 3 Excessive water remaining above the filter plate after the rinse cycle check for kinked drain hoses or blocked waste connection 4 No water supply check water is on and there is water pressure e Ifa fault occurs consult the Problem Solver Section of the Use amp Care Manual 6 If unable to resolve contact Customer Care Center Ensure Power is connected and is switched ON Oo Oo 0 OA oO 0 aS Ensure the water supply is connected and ON LEAVE ALL LITERATURE WITH THE CUSTOMER
16. rol Badge Position All marking out to be Badge can be located anywhere within the Mounting Zone shown Handle position will need done on the back surface to be taken into account of the Drawer Front Record your Badge Position from Centre of Drawer here A Max 7o 188mm Record your Badge Position from Top of Drawer Front here e Min 1 e 43mm Max 4 3 121mm Available Control Badge 1 IMPORTANT Mounting Zone When mounting the handle ensure fastenings do not protrude beyond the back surface of the Drawer Front 1 IMPORTANT 4 1 4 Accuracy is essential when cutting the Badge Mounting Hole to ensure a neat fit to hold the Badge Cutout Dimensions Cut out Badge Mounting Hole in the chosen position see Control Badge Mounting Zone on diagram above A Control Badge Template Part No 526253 is available on request from Fisher amp Paykel or alternatively a Template can be found on the Mounting Bracket enclosed badge with the product 7 2 p 56 5mm gt 1 n 14 28 5mm The Badge Mounting Hole is an ellipse shape Page DS_13 4 1 5 Drawer Front Mounting Bracket Nut Holes Using a 32 8 5mm diameter drill bit drill out the four screw holes in each door panel to a depth of 16 14mm Remove burrs P warina Use of a depth gauge is recommended when 10 257mm go 242mm 9
17. y the DishDrawer may be permanently connected to flexible conduit Remove the flex and cable clamp Fit suitable cable clamp for the conduit and terminate the wiring as shown Use the solderless lug and washer supplied with the product parts to terminate the ground wire Ground ED warnina The Product MUST NOT be plugged in at this stage 1 WARNING If permanently connecting ensure power is isolated Page DS_08 Pg Wiring Plumbing and Services should be completed before attaching the flexible extrusion Page DS_09 STEP 2 3 FLEXIBLE EXTRUSION ATTACHMENT FOR 24 610mm CAVITY DishDrawer Flexible Extrusions Chassis Trim 2 3 1 Flexible Extrusions are supplied to enable the installer to help fill any excess space between the sides of the DishDrawer and the cavity The two lengths of Flexible Extrusion supplied should be attached before pushing the DishDrawer into the cavity for final installation This Extrusion is designed to fit a 24 610mm width cavity 2 3 2 Open the drawers exposing the chassis trim 2 3 3 Remove backing from adhesive tape on Flexible Extrusion 2 3 4 Apply as per drawings ensuring the curved edge of the Flexible Extrusion fits around the corner of the chassis trim 2 3 5 When checking final fit ensure DishDrawer is centered and there are even tolerances between DishDrawer and cavity INSERTING DISHDRAWER INTO
Download Pdf Manuals
Related Search