Fisher & Paykel DD36STI User's Manual
Contents
1. to install the Dishdrawer panels correctly could invalidate any warranty or liability claims 2 PANEL PREPARATION Installation diagrams for illustration purposes only height of panel 3 min 6 8 Air gap The following calculations assume the top of the panel is aligned with the top of the adjacent cabinetry width of the panel Measure A the width between adjacent door drawer fronts and write it in the first box below then complete the equation A door clearance panel width eg 35 7e 2x Te 35 Va 900 mm 2 5 mm 895 mm A door clearance panel width i Ea min Ve 2 5 mm min 33 16 855 mm height of the panel Measure B door drawer height or equivalent and write it in the first box below then complete the equation B panel height eg 18 76 Ve 2 mm Air gap TOP M 18 5 480 mm 5e 8 mm Air gap BOTTOM 470 mm panel height B Ye 2 mm Air gap TOP 3 e 8 mm Air gap BOTTOM min 18 470 mm Note when the top of the DishDrawer has to be lower than the adjacent cabinetry the panel can be increased in height Front Panel material a 1H 6 18 20 mm panel thickness Adequately sealed to withstand moisture 122 F 50 C 80 RH 3 PARTS SUPPLIED Supplied separately Attached to product fi i HHI WR Panel mounting Integrate2. Front panel preparation Integrated models only DishDrawer DD36STI DD90S H TI models Important SAVE THESE INSTRUCTIONS The models shown in this document may not be available in all markets and are subject to change at any time For current details about model and specification availability in your country please visit our local website listed at the end of this document or contact your local Fisher amp Paykel dealer SAFETY AND WARNINGS WARNING Electrical shock hazard WARNING To reduce the risk of electric shock fire or injury to persons the installer must ensure that the DishDrawer is completely enclosed at the time of installation Before fitting the front panel and connecting the integrated badge make sure that the DishDrawer is completely enclosed by cabinetry and disconnected from the power supply The integrated badge must be electrically connected by a suitably qualified installer Failure to follow these warnings may result in electrical shock injury or fire A WARNING Cut hazard Take care panel edges are sharp Failure to use caution could result in injury or cuts Fisher amp Paykel Important safety instructions Read these instructions completely and carefully Ensure the product is not plugged in Installation of DishDrawer panels requires basic mechanical and electrical skills Installation must comply with your local building and electricity regulations Failure
3. d rectangular badge 1 Panel bracket 1 Integrated door seal 1 screws 14 Satin chrome supplied ZONE REQUIRED FOR BADGE A WARNING Electrical Shock Hazard Before continuing ensure that the product is disconnected from the power supply Failure to follow this warnings may result in electrical shock injury or fire 5 127 mm 4 10 Ye 255 mm 6 ROUTE BADGE THROUGH PANEL 7 SECURE PANEL BRACKET TO PANEL Important Use all 14 screws provided as shown 56 16 mm Vs Important Ensure the rubber seal between the drawer and panel is kept in place D EE DK Ny Push the panel lectrical Shock Hazar in then up t Connect the integrated badge ground earth wire SS I ta p to to one of the two tabs provided on the panel bracket ocate To ground earth the panel bracket connect the ground earth wire from the product to the other tab Failure to follow these warnings may result in electrical shock injury or fire www fisherpaykel com www fisherpaykel ca www fisherpaykel co nz www fisherpaykel com au www fisherpaykel co uk www fisherpaykel ie 590018A US CA NZ AU GBIE 03 10 Front panel adjustment Prefinished models only f DishDrawer Fisher amp Paykel DD36SDFTX DD90SDFTM DD90SDF H TX mothe Important SAVE THESE INSTRUCTIONS The models shown in thi
4. ock injury or fire RECONNECT THE POWER SUPPLY www fisherpaykel com www fisherpaykel ca www fisherpaykel co nz www fisherpaykel com au www fisherpaykel co uk www fisherpaykel ie 590018A USCANZAUGBIE 03 10
5. p Failure to use caution could result in injury or cuts 2 DISCONNECT FROM POWER SUPPLY 3 REMOVE FRONT PANEL Failure to follow this warning may result in electrical shock injury or fire o o o Lie the door panel flat on its front on a protected surface Be careful not to damage the handle Loosen these screws Remove these fixing screws Loosen these screws SLIDE BRACKETS TO SUITABLE HEIGHT SETTING O TIGHTEN PANEL BRACKETS There are three pre drilled height settings Slide brackets to lt Tighten these screws ________ je preferred height setting mM Replace these fixing screws gt Pe Tighten these screws _ _ _ gt Low setting Factory setting High setting o 1 5 mm o 1 5 mm RECONNECT CONTROLS 9 REATTACH PANEL Important Ensure the rubber seal between the drawer and panel is kept in place A WARNING Push the Electrical Shock Hazard panel in then up to locate Connect the ground earth wire of the controls to one of the two tabs provided on the panel bracket To ground earth the panel bracket connect the ground earth wire from the product to the other tab Failure to follow these warnings may result in electrical sh
6. s document may not be available in all markets and are subject to change at any time For current details about model and specification availability in your country please visit our local website listed at the end of this document or contact your local Fisher amp Paykel dealer If after installation the front panel of your DishDrawer is not correctly aligned with the front panels of surrounding cabinetry it can be adjusted as follows T SAFETY AND WARNINGS A WARNING Important safety instructions Electrical shock hazard Read these instructions completely and carefully WARNING To reduce the risk of electric shock fire or injury to persons the Ensure the product is not plugged in installer must ensure that the DishDrawer is completely enclosed at the time of a Installation of DishDrawer panels requires basic mechanical and electrical skills installation a Installation must comply with your local building and electricity regulations Before fitting the front panel and connecting the controls make sure that the a Failure to install the Dishdrawer panels correctly could invalidate any warranty or liability claims DishDrawer is completely enclosed by cabinetry and disconnected from the power supply The controls must be electrically connected by a suitably qualified installer Failure to follow these warnings may result in electrical shock injury or fire A WARNING Cut hazard Take care panel edges are shar
Download Pdf Manuals
Related Search