Fisher & Paykel CG302D User's Manual
Contents
1. height of product excluding burners dials pan supports 64 64 64 64 64 64 64 B overall width of product 300 450 600 600 750 900 900 C overall depth of product 530 530 530 530 450 450 530 D height of chassis below top of bench 59 59 59 59 59 59 59 E width of chassis 256 406 555 555 706 856 856 F depth of chassis 486 486 486 486 410 410 486 G overall width of cutout 265 415 560 560 715 865 865 H overall depth of cutout 490 490 490 490 410 410 490 corner radius of cutout max 10 max 10 max 10 max 10 max 10 max 10 max 10 J distance from top of bench to centre of gas inlet on product 30 30 30 30 30 30 30 K distance from edge of chassis to gas inlet on product 21 21 21 21 21 21 21 5 CLEARANCE DIMENSIONS Clearance dimensions mm H l minimum clearance from left edge of cutout to nearest combustible surface minimum clearance from right edge of cutout to nearest combustible surface minimum clearance from rear edge of cutout to nearest combustible surface nearest non combustible surface minimum height of non combustible material when used on adjacent walls minimum clearance from glass surface to rangehood any other overhead exhaust fan downward facing combustible surface downwards facing tiled or fire resistant surface minimum clearance below top of benchtop to combustible surface Fisher amp Paykel oven or nearest non combustible surface minimum distance from right edge of cooktop to gas connecti2. ERATION L Do all burners ignite both individually and in combination L Are the flames consistent and appropriately sized L Have you demonstrated the basic operation to the customer www fisherpaykel com
3. INSTALLATION INSTRUCTIONS Gas on glass cooktop CG302D CG451D CG603D CG604D CG752D CG903D amp CG905D models NZ AU Fisher amp Paykel 590149D 02 13 1 SAFETY AND WARNINGS A WARNING Electrical shock hazard Before carrying out any work on the electrical section of the appliance it must be disconnected from the mains electricity supply Connection to a good earth wiring system is absolutely essential and mandatory Alterations to the domestic wiring system must only be made by a qualified electrician Failure to follow this advice may result in electrical shock or death AA WARNING Cut hazard Take care some panel edges are sharp Failure to use caution could result in injury or cuts IMPORTANT SAFETY INSTRUCTIONS Particular attention shall be given to the relevant requirements regarding ventilation Read these instructions carefully before installing this product Please make this information available to the person installing the appliance as it could reduce your installation costs This appliance is to be installed and serviced only by an authorised person Installation must comply with your local building and local gas authority codes and electricity regulations Incorrect installation for which the manufacturer accepts no responsibility may cause personal injury or damage and could invalidate any warranty or liability claims These appliances are registered in New Zealand at www energysa
4. al thread 1 3 GAS RATE SUMMARY MODELS SEMI RAPID SEMI RAPID DUAL WOK DUAL WOK AUX SEMI RAPID CELDA CG451D CG603D SEMI RAPID SEMI RAPID DUAL WOK DUAL WOK MINI WOK CG604D CG752D SEMI RAPID SEMI RAPID DUAL WOK DUAL WOK SEMI RAPID DUAL WOK CG903D CG905D 3 GAS RATE SUMMARY All appliances are factory set for Natural gas or LPG and are not convertible Check the appliance data label Jet size mm BURNER LPG 2 75 Jet size mm BURNER LPG 2 75 ii Nominal pressure with at least one large burner on High CG302D AUX Nominal ratin MJ h SEMI RAPID Nominal Jet size ratin mm CG451D DUAL WOK Nominal rating MJ h Jet size mm CG603D SEMI RAPID Nominal rating MJ h Jet size mm CG604D CG752 CG903 amp CG905 SEMI RAPID Nominal Jet size rating RAPID Nominal Jet size rating MINI WOK Jet size Nominal rating MJ h Jet size mm DUAL WOK Nominal ratin MJ h Jet size mm DUAL WOK Nominal rating MJ h 4 PRODUCT amp CABINETRY DIMENSIONS A NY TOP TOP Note Gas inlet connection is located in the rear right corner FRONT REAR SIDE Product and cabinetry dimensions mm a a n Q Q Q Q Q Q Q w A a a N o ro o N 9 gt N 9 o o o o
5. ating at highest ON i i highest setting setting I ALL Models mm m Make sure the connection point will be accessible with the cooktop installed m Toenablethe gas supply to be readily shut off by the customer make sure the connection is fitted with an isolating valve close to the cooktop Ifconnecting the gas with a flexible hose Ensure the hose is long enough to allow for removal of cooktop for servicing Make sure the connector is located as shown in step 5 CLEARANCE DIMENSIONS The hose assembly must be AS NZS 1869 Class B or D certified with an Rp 2 ISO 7 1 female thread connection The hose assembly must be no longer than 1 2 min length with minimum internal diameter of 10 mm and comply with relevant AS 5601 NZS 5261 requirements The hose must not be kinked subjected to abrasion or permanently deformed The hose must not be near or in contact with any hot surfaces e g base of metal hotlplate flue or chassis of underbench oven etc AFFIX DUPLICATE DATA LABEL SOMEWHERE ACCESSIBLE 8 PLUG COOKTOP IN Duplicate data label 17 TEST OPERATION To check that the ignition system operates correctly light each burner by itself then all burners in combination Check for a well defined blue flame without any yellow tipping Ifany abnormality is evident check that the components of the burner assembly are located properly If proper operation cannot be obtained contact Customer Care or your
6. ed recess max 2 max 2 max 2 max 2 max 2 max 2 max 2 M height of routered recess 5 5 5 5 5 5 5 minimum clearance below top of benchtop to N combustible surface 75 75 75 75 75 75 75 Fisher amp Paykel oven or nearest non combustible surface 70 70 70 70 70 70 70 6 FLUSH MOUNTING INSTALLATION RECOMMENDED ROUTER THE BENCHTOP TO THE FIT THE CLAMPING BRACKETS MASK OFF THE AREA TO BE SPECIFIED DEPTH SILICONED 2221 lt AJ Z view from below A A Choose most appropriate slot for benchtop 4 WIPE OFF EXCESS SILICONE IF REMOVING PRODUCT CUT AROUND THE SILICONE TO REMOVE PRODUCT 2 N Ensure silicone does not leak underneath glass 7 DISCARD PACKAGING Floating nut Fibre washer Elbow 1 2 BSP external thread REMOVE THE TWO TRANSIT SCREWS SSS Te L Repeat on the other side 10 LOWER GENTLY INTO THE CUTOUT AX l 10 FIT CLAMPING BRACKETS BASED ON THE 12 SECURE TO BENCHTOP P BENCHTOP THICKNESS Repeat on all the other sides 13 CONNECT TO GAS SUPPLY 44 CHECK ALL CONNECTIONS FOR GAS LEAKS NG Models LPG Models m Make sure to fit the supplied m Make sure to fit the supplied m mm regulator test point adaptor GAS Lp 9 m Adjustto obtain a test point m Make sure the supply pressure pressure of 1 kPa with all O is regulated to 2 75 kPa with all pog 1 burners operating at burners oper
7. fety govt nz and Australia with SAI Global at www saiglobal com This gas appliance is suitable for connection only to the gas type for which it was set at the factory as declared on the appliance data label It is not convertible for use on any other gas type If in doubt refer to the local gas network operator or gas supplier to confirm gas type at installation site Do not modify this appliance Donot use or store flammable materials on or near this appliance Do not spray aerosols in the vicinity of this appliance while it is in operation Packing elements eg plastic bags polystyrene foam staples packing straps etc and tools should not be left around during and after installation especially if they are within easy reach of children as these may cause serious injuries You must remove the transit screws before installing the cooktop See step 8 of installation instructions Before you install the appliance please make sure that the local distribution conditions nature of gas and pressure and the adjustment of the appliance are compatible For adjustment conditions for this appliance see Gas rate summary a suitable disconnection switch is incorporated in the permanent wiring mounted and positioned to comply with the local wiring rules and regulations A means of disconnection with at least a 3 mm air gap contact separation in all poles must be incorporated into the fixed wiring in accordance with the wiring ru
8. h mounting the cooktop The owner must ensure the cooktop has Q been cut out from the benchtop before servicing can be carried out Fisher amp Paykel will not be liable for any costs associated with removing or replacing a flush mounted and or sealed in product nor for repairing any damage that may be incurred by doing this TOP Note Gas inlet connection is located in the rear right corner e 5 To REAR SIDE Product and cabinetry dimensions mm a a a a n n Q Q Q Q Q Q Q w amp a a N ro N w gt o o o ie A overallheight of product excluding burners dials and pan supports 64 64 64 64 64 64 64 B overall width of product 300 450 600 600 750 900 900 C overall depth of product 530 530 530 530 450 450 530 D height of chassis below top of bench 64 64 64 64 64 64 64 E width of chassis 256 406 555 555 706 856 856 F depth of chassis 486 486 486 486 406 406 486 G overall width of routered recess 305 455 605 605 905 905 G width of cutout 265 415 560 560 715 865 865 H overall depth of routered recess 535 585 535 535 455 455 535 H depth of cutout 490 490 490 490 410 410 490 l corner radius of cutout max 10 max 10 max 10 max 10 max 10 max 10 max 10 J distance from top of bench to centre of gas inlet on product 35 35 35 35 35 35 35 K distance from edge of chassis to gas inlet on product 21 21 21 21 21 21 21 L corner radius of router
9. les unless the local wiring rules allow for alternative means the appliance is connected to a 220V 240V 50Hz 10 A power supply only and earthed via the power supply cable there is a power outlet within reach of the power supply cable 900 mm from the centre rear of the product This must be accessible after installation The power supply cable should not touch any metal parts a if the power supply cable is damaged it is replaced only by the special cable Part no 534050 Flex Terminal Block Assy NZ AU obtainable from authorised Fisher amp Paykel Service Agents the supply connection point gas shut off valve is accessible after installation benchtop is made of a heat resistant material the installation complies with all the requirements of Australian and New Zealand Gas Installation Standards AS NZS 5601 1 2010 including that the product has to be installed so that the surface temperature of any nearby combustible surface will not exceed 65 C above ambient See step 5 Clearance Dimensions When you install the appliance We do not recommend you flush mount or seal this appliance into the bench with silicone or glue Doing so will make future servicing difficult Fisher amp Paykel will not be liable for any costs associated with removing or replacing a sealed in appliance nor for repairing any damage that may be incurred by doing this f installed with an approved flexible hose the hose should not co
10. me in contact with the bottom of the appliance or any sharp edges Flexible hose assemblies should be AS NZS 1869 Class B or Class D certified Seal exposed bare edges of the cutout with an oil based paint or moisture proof polyurethane to prevent possible moisture creeping between the cooktop trim and the benchtop Take extreme care not to chip crack or break the top glass surfaces during installation A heavy metal tool or part accidentally dropped on the glass could damage it If after following the instructions given correct performance cannot be achieved please contact your nearest Fisher amp Paykel Authorised Service Centre Customer Care or contact us through our website listed at the end of this document 2 PARTS SUPPLIED Dual Wok Pan support Pan support Mini wok Pan Small pan support 1 Models with a Dual Wok only not supplied with support 1 some models only Dual Wok only models CG604D only T Clamping LPG test point NG regulator 1 brackets 4 adaptor 1 NG models and screws 4 LPG models only only Installing multiple products lt gt Wok stand 1 Note if installing multiple products adjacent to each other within the same cutout a separate joining strip kit is required for installation The kit is available from the nearest Fisher amp Paykel Authorised Service Centre or our website listed at the end of this document Fibre washer 1 e Elbow 1 9 BSP extern
11. nearest F amp P Authorised Service Centre The cooktop must not be used by the customer until proper operation has been achieved yellow tip 000 good flame 16 FIT PAN SUPPORTS Ensure the pan supports are located securely and in the correct orientation refer to User guide 12 FINAL CHECKLIST i Y TO BE COMPLETED BY THE INSTALLER Installers name O Have you installed the clamping brackets O Have you verified that the type of model factory set for NG or LPG Installation C matches the type of gas at the site of installation Date of installation 444 L Have you used the fibre washer supplied L Have you leak tested all connections LEAVE THESE INSTRUCTIONS WITH THE CUSTOMER L Is the appliance set to the correct working pressure Important L Have you affixed the supplied duplicate data plate label on an adjacent SAVE THESE INSTRUCTIONS surface accessible to the customer The models shown in this document may not be available in all markets and are subject to change at any time For current details about model and specification availability in your country please visit our local website listed at the end of this document or contact your local Fisher amp Paykel Is the cooktop earthed dealer Have you checked that the power supply cable is NOT touching the cooktop OP
12. on point on wall if using a flexible hose distance from floor to gas connection point on wall if using a flexible hose maximum overall depth of overhead cabinetry Qqcot55 120 120 160 45 150 650 800 650 500 70 65 250 min 800 max 850 600 e u o 85 45 150 650 800 650 500 70 65 250 min 800 max 850 600 lt 0992 115 115 160 45 150 650 800 650 500 70 65 250 800 850 600 160 45 150 650 800 650 500 70 65 250 800 850 600 125 45 150 650 800 650 500 70 65 250 800 850 600 lt 0692 115 115 125 45 150 650 800 650 500 70 65 250 800 850 600 as065 130 115 160 45 150 650 800 650 500 70 65 250 min 800 max 850 600 Note Ensure there is an earthed power outlet within 900 mm of the centre rear of the product The gas connector on the wall should be 800 850 mm H above the floor and to a distance of at least 250 mm G outside the width of the product on the right hand side It should be accessible with the product installed 6 FLUSH MOUNTING INSTALLATION RECOMMENDED A WARNING We do not recommend flush mounting and sealing as servicing requires the cooktop to be removed from the benchtop The owner carries all risk for flus
Download Pdf Manuals
Related Search