Faria Instruments MG2000 User's Manual
Contents
1. 3 COG 265 1 Mag LAT LONG 40 42N 173 35W GPS Speed 16 7 Page 3 Heading Displays the GPS heading received from the GPS NMEA0183 signal if installed and connected The display will be in TRUE or MAG heading based on the SET GPS COG DISPLAY setting selected in the edit mode Note If magnetic bearing is not available from the GPS unit the operator will be unable to select MAG in the set GPS COG display function In addition the screen display will change to WARNING 265 1 True LAT LONG 40 42N 173 35W GPS Speed 16 7 The display will continuously flash at a slow rate to ensure that the operator is aware that the displayed COG is being presented in relation to true north not magnetic north Lat Long Displays the GPS latitude and longitude of the current location received from the GPS NMEA0183 signal if installed and connected GPS Speed Displays GPS Speed Over Ground SOG speed Screen 4 Air Temp 70 4 F Water Temp 60 8 F CLOCK 10 13 Air Temp ANALOG INPUT Displays current air temperature Water Temp Page 4 From bus or an Analog input Displays current water temperature Clock Displays time received from the GPS NMEA0183 signal if installed and connected The display will be in 12 or 24 hour format based on the set clock type setting selected in the edit mode LCD Display Screens In the Normal mode p2. CLOCK 10 13 AM Fuel Level AAA ADO COG 265 1 Screen 2 GPS Speed 16 7 Trip Log 320 5 Miles Range 185 5 Miles Screen 3 COG 265 1 Mag LAT LONG 40 42N 173 35W GPS Speed 16 7 Screen 4 Air Temp 70 4 F Water Temp 60 8 F Barometer 30 50 PSI Note The Air Temp is not displayed when the paddle wheel signal is selected Description The MG2000 Speedometer receives digital data via the Faria Serial Bus from the MG2000 Tachometer If the speed signal is available on the bus then that will be sent to the speedometer If there is no speed signal on the engine bus then the analog inputs are used Analog inputs are provided for two sensors a paddle wheel speed sensor or an air temperature sensor and a water temperature sensor A direct pressure port allows monitoring of pitot pressure for the speedometer The Faria MG2000 Speedometer will turn on when the ignition key is turned on and will turn off when the ignition key is turned off The unit will power up showing the default screen selected by the user prior to shut off The instrument has three push buttons M Mode Down and Up that control the functions available The M Mode button is used to change the function of the LCD display and to access submenus and adjustable settings The Down and Up buttons are used to modify the settings a F In the Normal operation mode pressing th
3. INSTRUMENTS Wu Z cr lt Owner s Manual MG2000 Speedometer rev B ecr 5668 08 2005 12 19 2005 Index Description Figure 1 Default Screens page 1 Description page 1 Normal Mode page 2 Contrast and Lighting page 2 Displayed Functions page 2 LCD Display Screens page 3 Screen 1 page 3 Screen 2 page 3 Screen 3 page 3 Screen 4 page 4 LCD Display page 4 Figure 2 Screen Sequence page 4 Figure 3 Modes page 5 Fuel Functions page 6 COG Course Over Ground page 7 Edit Mode page 8 Select Default Screen page 8 Display next screen page 8 Reset Trip Log page 9 Organize user screens page 9 Organize screen 1 page 9 Speedometer Calibration page 10 Select Speedometer Signal page 10 Adjust Clock Offset page 11 Select Set Clock Type page 11 Select Adjust COG Type page 11 Select Self Test page 12 Select Software ID and Revision page 12 Available Functions for Display in MG2000 Speedometer page 13 MG2000 Speedometer Manual The MG2000 Speedometer combines the features of a speedometer and several digital instruments into one unit The MG2000 Speedometer is analog in appearance butis driven by a stepper motor for digital accuracy The high resolution LCD screen displays information for many other functions and the various screens can be configured as the user wishes As received the screens are configured as shown in Figure 1 Figure 1 Screen 1
4. d and connected The display will be in 12 or 24 hour format based on the set clock type setting selected in the edit mode Fuel Level ANALOG INPUT Displays setting of the analog fuel level sender Data is received via the Faria Bus from the tachometer Heading Displays the GPS heading received from the GPS NMEA0183 signal if installed and connected The display will be in TRUE or MAG heading based on the set GPS COG display setting selected in the Edit mode Note If the magnetic bearing is not available from the GPS unit the operator will be unable to select MAG in the set GPS COG display function In addition the screen display will change to CLOCK 10 13 AM Fuel Level AAAMOOO Warning 265 1 True The display will continuously flash at a slow rate to ensure that the operator is aware that the displayed COG is being presented in relation to true north not magnetic north Screen 2 GPS Speed 16 7 Trip Log 320 5 Miles Range 185 5 Miles GPS Speed Displays GPS SOG speed received from the GPS NMEA0183 signal if installed and connected Trip Log Displays the travel distance since last reset Range Displays the distance that can be traveled with the current amount of fuel as measured by the fuel left set in the Tachometer and the current GPH being used by the engine as received via the Faria Bus from the ECU tachometer Screen
5. ds to select Speedometer Calibration Press Up or Down to select another function or Mode to return to Normal mode NOTE To calibrate the speedometer another reference must be available This can be the GPS speed SOG a radar gun or some other source of accurate speed indication Maintain a constant speed and heading to allow the reference and the speedometer to stabilize before attempting to calibrate the speedometer Calibration accuracy is best if the speedometer is calibrated at mid range on the dial Press the Up or Down button while observing speedometer pointer When speedometer pointer indicates the same speed as the reference press and hold Up and Down for 2 seconds to save the calibration and return to Edit mode Press Up or Down to select another function or Mode to return to Normal mode Select Speedometer Signal NOTE This function is normally only used by OEMs and dealers Do not change this selection without ensuring that the correct selection is being made Consult your dealer before changing this selection This signal may come from the bus in which case that signal is used in lieu of these inputs Press and hold the Up and Down for 2 seconds to select Speedometer Signal Press Up or Down to select another function or Mode to return to Normal mode Pres
6. e Software Id and revision Press Up to select another function or Mode to return to Normal mode Page 12 OJJAN gt ND AJO D Select Self Test The Self Test Mode Is in Operation Software Id and Revision Mini gateway PGFXXXX X Available Functions for Display in MG2000 Speedometer Screens The functions listed below can be displayed in the user configured screens All of the functions may not be available in your installation If a function is selected for display and that function does not appear on the screen the function does not exist in this installation A function is selected for display by selecting it s number from the list below Clock COG Course Over Ground GPS Speed LAT 8 LONG Fuel Level Barometer Air Temperature Analog input to MG2000 Speedometer from air temp sender 8 Water Temperature from bus 9 Trip 10 Odometer 11 Range NOaORWN gt Page 13 Copyright 2005 by the Thomas G Faria Corporation Uncasville CT No part of this publication may be reproduced in any form in an electronic retrieval system or otherwise without the prior written permission of the company Faria is the trademark of the Thomas G Faria Corporation
7. e Mode button and then pressing Down or Up causes the display to cycle between the available screens Press the Mode button to exit the Screen Selection mode and return to Page 1 Normal mode If no buttons are pushed for 4 seconds the current screen will stay selected and the unit will return to Normal mode see Figure 2 amp 3 From the Normal mode press the Mode and Up buttons to change to the Edit menu see Figure 3 3 When the Edit menus have been selected pressing the Mode button causes the instrument to return to Normal mode Press the Down or Up to cycle between the available Edit functions Press and hold the Down and Up buttons for two 2 seconds to select an Edit function to change Within each editing function the Down or Up buttons select settings or sub functions Follow the instructions in the Edit mode section of this manual to save the new settings after you select adjust them Normal Mode When the MG2000 Speedometer is Page 2 turned on the unit enters a Self Test mode The screen will display The Self Test Mode Is In Operation for 10 seconds The warning lights and back lights will flash When this is complete the user selected Default screen will appear Note The information below applies to the MG2000 S
8. e fuel remaining Each filled block represents 1 8 of a tank and when the fuel tank is empty only empty blocks will be displayed For best accuracy the fuel level sender should be calibrated as described in the MG2000 Tachometer manual Manual settings The Fuel Left and Range display values are dependant on accurately setting the values for Fuel Tank Size and either Fuel Tank Full or Amount of Fuel in the MG2000 Tachometer Fuel Left is calculated based on the amount of fuel entered in these settings the amount of fuel the operator indicates is in the fuel tank and the fuel flow of the engine Range is calculated based on Fuel Left fuel flow and current speed COG 265 1 Mag LAT LONG 40 42N 173 35W GPS Speed 16 7 WARNING 265 1 True LAT LONG 40 42N 173 35W GPS Speed 16 7 COG Course Over Ground If deviation information is not available from the connected GPS the COG display will default to the display shown at left This is the normal display with COG indicated as it would be displayed on a compass If desired True North data can be displayed by selecting it in the set GPS COG display in the edit mode If deviation information is available from the GPS the COG display can be selected to display the screen shown at left The display will flash slowly to ensure the operator is aware that the display is showing True North bearing True Nort
9. h bearing is different from Magnetic North bearing by the amount of magnetic bearing deviation at the boat s current location Please ensure that the local magnetic deviation is taken into account if this display is to be used for navigation Page 7 Edit Mode The Edit mode is used to adjust or set the values of functions and options in the MG2000 Speedometer The procedure below specifies the steps to be taken in the Edit mode to adjust set each option To enter Edit mode press Mode and Up button while in Normal mode To return to Normal mode press Mode button once while in Edit mode Functions that are set or adjusted in the Edit mode 1 Select Default Screen 2 Reset Trip Log 3 Organize User Screens 4 Speedometer Calibration 5 Select Speedometer Signal 6 Adjust Clock Offset 7 Set Clock Type 8 Adjust COG Type 9 Select Self Test 10 Software ld and Revision O O Displa 1 Select Select Default Screen 2 Default 3 Screen Press and hold the Up and Down for 2 seconds to select the Default Screen Press Up or Down to select another function or Mode to return to Normal mode 1 Default Display Screen 1 is the Default at first turn on 2 Display 3 Screen 1 Press and hold the Up and Down for 2 seconds to select screen 1 as the Default Screen and exit 1 Default Pres
10. peedometer as if received with no user changes to the screen selections Display Contrast In the Normal operating mode the instrument display contrast and display mode can be adjusted by pressing the Down and Up buttons a 9 With the display in Positive mode black on white pressing the Down button decreases the contrast Pressing the Up button increases contrast Continuing to press the Up button causes the display to reverse to the Negative mode white on black The contrast in this mode is controlled the same way as the Positive mode To return to Positive mode continue to press the Down button until the display reverses The instrument lighting intensity is controlled by the lighting adjustment in the MG2000 Tachometer Lighting level signals are received via the Faria bus Displayed Functions MG2000 Speedometer The MG2000 Speedometer is a digital instrument with the appearance of an analog instrument The MG2000 Speedometer receives it s input from a paddle wheel speed sensor OR a pitot pressure input The Edit mode allows selection of the paddle wheel or pitot inputs calibration of the speedometer A microprocessor controlled stepper motor moves the pointer to display speed Screen 1 CLOCK 10 13 AM Fuel Level AAAMOOO COG 265 1 Clock Displays time received from the GPS NMEA 0183 signal if installe
11. ress the Mode button once to enter screen q Select mode Use the Up or Down buttons to move between screens Figure 2 Screen 1 Default Screen 2 Screen 3 Screen 4 Figure 3 LCD Display Screens 3 Increase decrease contrast l 40 sec 4 sec Auto Auto Return Return I I Select Q RA to move 1 or between screens Mode v See Figure 2 1 I I l 1 I I I I I I I I I I I l l I 1 Use to move between A or Edit Functions y 1 Select Default Screen 2 Reset Trip Log 3 Organize User Screens 4 Speedometer Calibration 5 Select Speedometer Signal 6 Adjust Clock Offset 7 Set Clock Type 8 Adjust COG Type 9 Select Self Test 10 Software Id amp Revision Use to change To cha nge settings o Edit Function Dashed lines indicate Auto Return to the Normal Mode after the indicated number of seconds with no button activity Page 5 Fuel Level Sender CLOCK 10 13 AM Fuel Level I 7 7 7 ADO Heading 265 1 Speedometer Manual Settings in the MG2000 Tachometer Fuel Fuel Tank Full Tank or Size Amount of Fuel Fuel Left GPS Speed 47 3 GAL 16 7 Fuel Used Trip 21 6 GAL 320 5 Fuel Avg Range 11 6 GPH 185 5 Page 6 Fuel Functions Fuel Level Sender This display is the equivalent of a standard fuel gauge and should be used as the reference for th
12. s Up or Down to select another screen 2 Display 3 Screen 2 Press and hold the Up and Down for 2 seconds to select this screen as the Default Screen and exit Press Up or Down to select another screen 1 De zul Repeat until desired Default screen is selected 2 Display p 3 Screen Press Up or Down to select another function or Mode to return to Normal mode 1 Reset Reset Trip Log 2 Trip 3 Log Page 8 Press and hold the Up and Down for 2 seconds to reset Trip Log to zero 0 Automatically resets trip log to zero and returns to Edit mode Press Up or Down to select another function or Mode to return to Normal mode Organize User Screens Press and hold the Up and Down for 2 seconds to select Organize User Screens Press Up or Down to select another function or Mode to return to Normal mode Organize screen 1 Press and hold the Up and Down for 2 seconds to select Organize Screen 1 Press Up or Down to select another screen or Mode to return to Edit mode Refer to the list of available functions in the owner s manual Press and hold the Up or Down to select the number of the function to be displayed in screen 1 line 1 Press and hold the Up and Down for 2
13. s the Up or Down button to scroll through the selections When correct choice is next to the selection arrow press and hold Up and Down for 2 seconds to save the selection and return to Edit mode Press Up or Down to select another function or Mode to return to Normal mode NOTE IF PITOT IS SELECTED WITH NO PITOT SIGNAL AVAILABLE THE SPEEDO WILL SHOW MAXIMUM SPEED AT ALL TIMES Page 10 Speedometer Calibration Calibrate Speedometer Select Speedometer Signal gt Pitot Tube Paddle wheel Adjust Clock Offset Press and hold the Up and Down for 2 seconds to select Clock Offset Press Up or Down to select another function or Mode to return to Normal mode OR Press Up or Down while observing clock When the clock display matches local time press and hold Up and Down for 2 seconds to save clock offset and return to Edit mode Note If the local time zone changes this adjustment must be repeated Press Up or Down to select another function or Mode to return to Normal mode Select Set Clock Type Press and hold the Up and Down for 2 seconds to enter Set Clock Type Press Up or Down to select another function Press Up or Down to scroll through the selections When the correct choice is nex
14. seconds to save selection for Screen 1 line 1 and advance to Screen 1 line 2 Press Mode to exit with no change made Refer to the list of available functions in the owner s manual Press and hold the Up or Down to select the number of the function to be displayed in screen 1 line 2 Press and hold the Up and Down for 2 seconds to save selection for Screen 1 line 2 and advance to Screen 1 line 3 Press Mode to exit with no change made Refer to the list of available functions in the owner s manual Press and hold the Up or Down to select the number of the function to be displayed in screen 1 line 3 Press and hold the Up and Down for 2 seconds to save selection for Screen 1 line 3 and advance to view new screen 1 Press Mode to exit with no change made Press and hold the Up and Down for 2 seconds to save new Screen 1 an exit Press Mode to exit with no change made Repeat this process for each of the remaining screens 2 3 4 WIN gt Organize User Screens Set up Screen 1 Screen 1 Line 1 Item XX Screen 1 Line 2 Item XX Screen 1 Line 3 Item XX Display Customer s New screen 1 Page 9 Press Up or Down to select another function or Mode to return to Normal mode Speedometer Calibration Press and hold the Up and Down for 2 secon
15. t to the selection arrow Press and hold the Up and Down for 2 seconds to save the selection and return to Edit mode Press Up or Down to select another function or Mode to return to Normal mode Select Adjust COG Type Press and hold the Up and Down for 2 seconds to enter Adjust COG Type Press Up or Down to select another function Press Up or Down to scroll through the selections When the correct choice is next to the selection arrow Press and hold the Up and Down for 2 seconds to save the selection and return to Edit mode Press Up or Down to select another function or Mode to return to Normal mode oa P oOI IN ND AJO D Set Clock Offset Adjust Clock Offset Set Clock Type Set Clock Type 24 Hour gt 12 Hour Adjust COG Type Adjust COG Type True North gt Magnetic Page 11 Select Self Test Press and hold the Up and Down for 2 seconds to select Self Test Press Up or Down to select another function This screen will display for 10 seconds The backlights will flash three times When Self Test is complete the unit will return to the Edit mode Press Up or Down to select another function or Mode to return to Normal mod
Download Pdf Manuals
Related Search