Faria Instruments Antares IS0250a User's Manual
Contents
1. Ma Mans una nr Owner s Manual 1S0250a ecr7106 9 2007 TABLE OF CONTENTS Part I Introduction Basic Operation Part II System Setup Input Setup Tank Setup Depth Setup Part III Operating Instructions Gauge Screen Gauge Screen 2 Quick View Screen Fuel Manager Screen Depth Temp Screen Tank Level Screen GPS Screen Radio Control Screen if available Main Menu Screen Part IV Menu Options User Settings Lighting Fuel Manager System Setup Units Calibrate Self Test Master Reset Diagnostics Part V Alarms Part VI Installation Wiring Diagrams Part VII FAQ Troubleshooting Part VII Warranty OO N G DU 10 11 12 13 14 15 16 17 18 19 19 20 21 22 25 26 21 28 29 31 38 39 Part I Introduction Congratulations on the purchase of your Faria Antares unit This owner s manual contains very important information regarding the installation setup and operation of your Antares To get the best results in operation and performance please take a few minutes to read this manual and get acquainted with the Faria Antares unit GPS IMAGE 1 1 Escape Button B2 Navigation Pad Up Down Left Right Arrows B3 Enter Button B4 Radio Button optional Screen Indicator B5 Power Button Bar To begin simply press the button to turn on your Antares It will take about 5 7 seconds for the Antares to complete its start up process Your Antares 1s re2. F id GPS The Fuel Flow Manager screen provides all the necessary information to optimize the fuel consumption performance of your boat The upper two quadrants can be customized to display various fuel flow information To customize these quadrants press aD The upper left quadrant will be highlighted yellow as pictured below Total Remaining 90 GAL Use the left or right navigation buttons to highlight either of the upper quadrants When the desired quadrant is highlighted press A list of available fuel flow information will appear in the center of the screen Use the up or down navigation buttons to highlight the desired information to be displayed then press aD The highlighted quadrant will change to the display selected Once you have set the quadrants to the desired information press ED to return to the normal operating mode Range mM Trip D Total Remaining 90 GAL Total Remaining 90 GAL Mall F im GPS D WARNING The Total Remaining calculation is not connected to the fuel level sender s on your boat and is not intended to 13 DEPTH TEMP SCREEN DEPTH 28 6 Fi The Depth Temp screen will display the current depth air temperature and water temperature For Depth and Water Temperature a digital Depth Water Temp transducer must be installed If no transducer is installed then the Depth quadrant will display Transducer Not Installed and the Water quadrant will d
3. HN0605 Power Analog Harness Tank 1 Tank 2 15 N MENO 19 N C 20 N C WIRE SIDE Tank 3 or Trim Air Temp or Analog PWS Radio k I RA J I i HN0605 HN0604 N ar OO CENTS MESA ERRET eeh IE 1 0 dx PH 1 RP LE GER _ i Ts CAD 1 A PRINTEO COPIES OF THIS DOCUMENT ARE UNCONTROLLEO AM MAT HOT BE CURRENT I a a L gt L L AXES t AL FORMAL MAT WTD BEL TEST GF 15 CRC Be Fad A CABLE AVARES 20 PA FAR BUS OUT EO NL eee peter i PRATEO COPES CF THIS DOCUMENT ARE UNCONTROLLED AM MAY HOT BE GUERENT 38 Part VII FAQ Troubleshooting The following items are common questions regarding the installation and use of the Antares unit If you are experiencing a problem not described in the FAQ section please visit www faria instruments com antares html for more detailed troubleshooting Problem Possible Cause Solution Improper connection to Check connection refer to NO ECU ALARM engine s harness HNO605 pg 35 No Depth Water Digital Depth Transducer Install a compatible digital depth Temp Signal not installed water temp transducer Check connection refer to Improper connection HN NMEA0183 GPS Antenna Install a NMEA0183 GPS No GPS Signal not installed antenna Improper connection Check connection Only some Antares are available with Radio control If your Antares does not have a No Radio Control Not available on Antares Blue Radio Button then it
4. until 5 00 p m Eastern Time One of our Marine Applications Specialists will review the problem with you in detail If no solution is found you will be given an authorization number to return the instrument postage prepaid and packaged to prevent damage while in transit along with your name address daytime telephone number sales receipt and a brief description of the problem to Faria Marine Instruments WARRANTY SERVICE PO Box 983 385 Norwich New London Turnpike Uncasville CT 06382 0983 It will be promptly returned to you postage prepaid once analyzed repaired or replaced Instrument styles which are no longer manufactured may be replaced with a similar instrument of equal or greater value Flux Gate Compass Systems should be returned with sensor For warranty service beyond the initial warranty period be certain to include your check or money order as stated on the Warranty fees table Removal reinstallation expenses any damage to an instrument resulting from natural disasters misuse neglect accident misapplication improper installation unauthorized repair or alteration and instruments purchased prior to March 1 1985 are not covered by this warranty Instruments returned to Faria Marine Instruments that are not covered under this warranty will be repaired or replaced at our nominal service rates or returned to you as is at your option Faria Marine Instruments expressly disclaims any liability for incidental of
5. SURE YOU WANT TO RESET ALL SETTINGS TO FACTORY DEFUALTS Master Reset _M JNO This screen will appear when Master Reset s selected from the Main Menu screen will automatically be highlighted If you do not wish to perform a Master Reset be sure that ND is highlighted and press You can also press ED to return to the previous screen without performing a Master Reset WARNING Performing a Master Reset will return all user defined and manufacturer set values to the default values 2 DIAGNOSTICS 2 DIAGNOSTICS CALIBRATE lt lt SELF TEST MASTER RESET DIAGNOSTICS Y DT D Ss PRESS ESC TO EXIT 4 The Diagnostics page displays the most recent engine error codes as reported by the engine s ECU Hours indicates at what engine hour an engine error has occurred Error indicates which engine error occurred To exit press Part V Alarms Your Faria Antares unit will display 3 types of alarms 1 Engine Alarms 2 Fuel Tank Level Alarms and 3 Depth Alarms When an alarm condition 1s present an Alarm pop up window will appear see image below and alarm icons will flash in the lower corners of the display screen o Ts To close the alarm pop up window and silence the alarm press EP The alarm icons will continue to flash in the lower corners of the display screen until the alarm condition is corrected Alarm Icons 4 Engine Alarm
6. analog paddlewheel sender is connected to pin 9 on HN0605 NONE No speed signal 1s connected Once you have saved all the appropriate settings press ED to return to the SYSTEM SETUP menu Step 2 TANK SETUP Use the navigation pad to highlight TANK SETUP then press DEPTH SETUP INPUT SETUP Tank Setup will allow you to 1 Name each tank 2 Set each tank s capacity and 3 Set a low level warning for each tank Note Refer to your boat owner x manual for the correct tank capacities Setting the tank capacity incorrectly will effect the performance of the Fuel Flow Manager Use the left or right navigation buttons to select either Tank 1 Tank 2 or Tank 3 Once the desired tank is selected press Now scroll up or down to select the setting to change and use the left or right arrows to make the appropriate changes TANK SETUP TANK 1 TANK NAME Z TANK1 CAPACITY 41234 GAL FUEL TANK 733 NO LOW LEVEL WARNING OFF 1 16 A A 3 16 1 4 PRESS ESC TO EXIT Note By selecting on the Fuel Tank option you are indicating that the tank connected to the associated sender is a fuel tank Any tank that is indicated as a fuel tank will be used by the Fuel Flow Manager for calculation If the associated tank is not a fuel tank then select NO Improper tank indication will effect the performance of the Fuel Flow Manager Once you have adjusted all the options to the desired settings press aD The icon on
7. does Screen Model not have the radio control option Unable to Control See list of compatible radios at Radio via Radio Connected to incompatible www faria Control Screen radio instruments com antares html Check connection of Jensen Remote Harness to Radio Plug Improper connection on HNO605 pg 36 Fuel Flow Manager Refer to Part Il System Setup not Working Tanks not properly set up for instructions Set Amount of Fuel to actual amount of fuel in tank s Refer Fuel Flow Manager Amount of Fuel not to FUEL MANAGER page 21 inaccurate properly set for instructions 39 MARINE INSTRUMENTS The choice of World Leading Boat Manufacturers sen CI a WS Tr fortan euer WATER SKI Iransferable Limited Lifetime Warranty We Supply Our Customers Ihe Highest Quality Product Achievable At Competitive Prices During the first 36 months from date of original retail purchase 12 months on PWC fog resistant gauges Fuel Managers Depth Sounders Commander Speedo Commander Tach Pilot I Pilot Il and MG2000 any instruments that fail due to defects in materials or workmanship will be repaired or replaced at Faria Marine Instruments option at no charge The Warranty is further extended indefinitely beyond the initial warranty period by enclosing the nominal fee as listed when submitting a warranty claim To submit a Warranty Claim call Faria Customer Service at 1 800 473 2742 weekdays 8 30 a m
8. each harness to be rotated about 1 4 turn Step 5 Connect available inputs to corresponding wire harnesses See pages 34 37 for detailed wiring information 33 Gimble Mount Step 1 Locate a flat surface on your boat s console to install the Antares Gimble Mount Bracket Step 2 Using a 3 16 drill bit drill two holes 2 7 inches apart as indicated in the figure below Step 3 Using the supplied mounting hardware mount the Gimble bracket through the holes you just drilled Step 4 Using the supplied fasteners mount the Antares unit into the Gimble bracket Step 5 Connect 9 pin HN0604 and 20 pin HN0605 wire harnesses to back of Antares unit Proper connection requires the locking ring on each harness to be rotated about turn Step 6 Connect available inputs to corresponding wire harnesses See pages 34 37 for detailed wiring information 34 9 MOLET HN0604 8 ECU GPS Harness 1 RED 7 YELLOW 2 BLACK 6 BLUE 3 WHITE 5 BROWN 4 GREEN WIRESIDE HEAT SHRINK TUBING gr ALPHA FIT 221 OR EQUAL WROZ43 CABLE BOC PWC JACKET 9 CONDUCTORS 20 AMG CAROL CSISZA OR COUMALENT GPS FARIA BUS E CA x 3 gt gt a N Q JDLZ IDU ZZ LA GPS ANTENNA OU 2 j J S J K E su E l N tm a gt gt A a L RI NMEA0183 HN0604 36 FARIA BUS DEUTSCH DIOE 25 IL OL Power Gnd
9. Active Q T gt S23 ys Al Depth Alarm Active a Ta S23 sa mi Fuel Tank Level Alarm Active E P 23 45 m When an alarm condition is corrected an Alarms Cleared pop up window will appear Depth 28 6 Ft Bearing 235 r You MUST press to close the Alarms Cleared window Alarms Cleared 29 ENGINE ALARMS LIST Your Antares unit will display the engine alarms listed in table 5 1 The Antares will display engine alarms as they are reported by the engine s ECU The Antares may not be able to display all available engine alarms When available the Antares will give a detailed description of the active alarm condition s If a description is not provided by the engine s ECU the Antares unit will most likely display Miscellaneous Engine Fault in the alarm pop up window NOTE Many engines are equipped with an internal protection system In the event that this protection system is activated by the engine s ECU your Antares unit may display Engine Emergency Stop in the alarm pop up window If this occurs your engine s ECU may limit power and it is recommended that you contact your dealer or marina immediately The Faria Antares unit has no control over your engine s internal protection system MG2000 J1939 Warnings Table EngineEmergencyStop CheckEngine LowOilPressure amber LowOilPressure red LowFuelPressure LowsystemVoltage HighSystem Voltage LowCoolantLevel HighBoostPressure Rev
10. Gasket GK0207 between the Antares and the panel Step 4 From back of panel install back clamp The four interior studs should line up with the four interior holes of the back clamp Tighten the supplied nuts washers and lock washers to 7 10 inch pounds slightly more than finger tight Step 5 Connect 9 pin HN0604 and 20 pin HN0605 wire harnesses to back of Antares unit Proper connection requires the locking ring on each harness to be rotated about 1 4 turn Step 6 Connect available inputs to corresponding wire harnesses See pages 34 37 for detailed wiring information E 5 ANEL BY CUSTOMER Sp QQ REAR VIEW EN 4 9 32 x 100 LONG MOUNTING STUDS co ANTARES FLUSH MOUNT PANEL CUTOUT amp H LES E 3 K Z E 8 C 4 O a b a 1 i F Created wi 13 lt 4 B 32 x 1 00 LONG OUNTING STUDS 5 ni 4 32 Gauge Mount Step 1 Cut a 3 3 8 round hole in your boat s console Step 2 Insert the Antares through the hole placing the Gauge mount gasket GK 1234 between the Antares unit and the panel Step 3 From back of panel install back clamp The two interior studs should line up with the two holes of the back clamp Tighten the supplied nuts washers and lock washers to 7 10 inch pounds slightly more than finger tight Step 4 Connect 9 pin HN0604 and 20 pin HN0605 wire harnesses to back of Antares unit Proper connection requires the locking ring on
11. INPUT SETUP TANK 2 SELECT SENDER TYPE EURO NONE Save Changes YES NO PRESS ESC TO EXIT INPUT SETUP TRIM TANK 3 SELECT SENDERTYPE EVINRUDE SUZUKI MERC YAMAHA TANK 3 US TANK 3 EURO NONE Save Changes YES NO PRESS ESC TO EXIT INPUT SETUP AIR TEMP SELECT SENDER TYPE NOT INSTALLED INSTALLED Save Changes YES NO PRESS ESC TO EXIT INPUT SETUP SPEED SOURCE SELECT SENDER TYPE DIGITAL PWS EN ANALOG PWS NONE Save Changes YES NO PRESS ESCTO EXIT TANK 1 Select the type of level sender connected to Pin 5 on HN0605 If nothing 1s connected select NONE TANK 2 Select the type of level sender connected to Pin 6 on HN0605 If nothing 1s connected select NONE TRIM TANK 3 Choose the type of analog trim sender or level sender connected to Pin 7 on HN0605 If nothing is connected select NONE AIR TEMP Select INSTALLED if an analog Air Temp sender is connected to Pin 9 on HN0605 If an air temp sender is not connected select NOT INSTALLED SPEED SOURCE Choose the type of speed signal to be used by the Antares Refer to your boats owner s manual to determine which type of speed options are installed on your boat and are connected to your Antares DIGITAL PWS A digital paddlewheel sender s connected via the J1939 backbone GPS A NMEA0183 GPS signal is connected ANALOG PWS An
12. LimitExceeded Over lemperature WaterlnFuel WaterlnFuel N A TABLE 5 1 30 Part VI Installation Wiring Diagrams INSTALLATION Your Faria Antares unit can be mounted to your instrument panel in 4 ways Panel Mount Flush Mount Gauge Mount and Gimble Mount Panel Mount Step 1 Cut a square hole with rounded corners to match the dimensions as indicated in the figure below Step 2 Insert the Antares unit from front of panel placing the Panel Mount Gasket GK0206 between the Antares and the panel Step 3 From back of panel install back clamp The four interior studs should line up with the four interior holes of the back clamp Tighten the supplied nuts washers and lock washers to 7 10 inch pounds slightly more than finger tight Step 4 Connect 9 pin HN0604 and 20 pin HN0605 wire harnesses to back of Antares unit Proper connection requires the locking ring on each harness to be rotated about 1 4 turn Step 5 Connect available inputs to corresponding wire harnesses See pages 34 37 for detailed wiring information 9 or deskPDF PDF Whiter Trial Hip www docudesk com ANTARES H lt CV0034 win created PDF C gt 31 Flush Mount Step 1 Cut a square hole with rounded corners to match the dimensions as indicated in the figure below Step 2 Install mounting studs at the dimensions indicated in the figure Step 3 Insert the Antares unit from back of panel placing the Flush Mount
13. N ADJUST PADDLEWHEEL LTorRT 4 TO MATCH GPS PRESS ENTER TO CONFIRM ED GPS 15 0 MPH SPEED CALIBRATION CALIBRATION SUCCESSFUL PADDLEWHEEL GPS 15 0 15 0 MPH MPH Step 1 Press Gu to begin speedometer calibration then follow the on screen instructions Your actual speed as reported by the active speed source will be displayed in the lower left quadrant If you have a GPS antenna connected to the Antares unit and a signal is present then your speed as reported by the GPS antenna will be displayed 1n the lower right quadrant Ifno GPS antenna 1s attached to the Antares unit then use a secondary GPS speed source for calibration Step 2 Press the left or right arrows on the navigation button to increase or decrease the speed value in the highlighted quadrant Step 3 When the speed value in the highlighted quadrant matches or is close the GPS speed value displayed in the lower right quadrant or the GPS speed value displayed on your secondary GPS speed source press When calibration 1s complete CALIBRATION SUCCESFUL will be displayed and the Antares will automatically return to the previous screen 24 TRIM CALIBRATION CALIBRATETRIM GD Press aD to begin Trim Calibration then follow the on screen instructions ehe SE Step 1 Set your engine to ts full down position then press aD DOWN POSITION PRESS ENTER Gig TRIM Step 2 Set your engine to the top of its trim range
14. ady to use when the Gauge 1 Screen appears Navigate through display and setup screens by pressing the up down left or right arrows on the navigation pad image 1 1 pg 4 After familiarizing yourself with the Antares screens please continue to read through your owners manual for detailed operating instructions BUTTON FUNCTIONS EY B1 Returns to previous page when in menu setup radio control screens silences alarms B2 Use to change screens scroll menu options adjust settings Gi B3 Select highlighted item GD B4 Activates radio control screen not available on all Antares models E B5 Turns unit on off shortcuts to lighting control screen SCREEN INDICATOR ICONS MENU SCREEN GAUGE SCREEN 1 Pl GAUGE SCREEN 2 Ps QUICK VIEW SCREEN FUEL FLOW MANAGER SCREEN DEPTH AIR TEMP WATER TEMP SCREEN C TANK S LEVEL SCREEN GPS GPS SCREEN Part II System Setup SYSTEM SETUP Your Faria Antares unit should already have been setup by either the boat manufacturer or by your dealer Check with your dealer before beginning the System Setup process In order to get the optimal performance out of your Faria Antares unit the following steps are recommended Some of the information needed to complete the setup process will be contained in your boat owner s manual Be sure to have your boat owner s manual available before beginning the Antares setup process To begin use the left or right arrows on the navig
15. ation pad once to Tune press and hold to Seek 9 SHIFT SCAN Press right or left on the navigation pad for Shift press and hold to Scan Press EY at any time to exit the Radio Control Screen 17 MAIN MENU SCREEN FUEL MANAGER SYSTEM SETUP UNITS The Main Menu screen provides access to the various setup screens available on your Faria Antares unit Use the up or down navigation buttons to highlight the desired menu option then press A detailed description of each sub menu is contained in Part IV Menu Options User Settings 18 Part IV Menu Options User Settings LIGHTING LIGHTING 9 Loo FUEL MANAGER mode BH Night SYSTEM SETUP w UNITS p y U T Ss ENTERTO SAVE amp EXIT This screen can also be accessed by tapping the button at any time Use the up or down navigation buttons to highlight the desired setting to adjust then use the left or right navigation buttons to adjust the highlighted section Press to save your changes and exit to the previous screen or ED to exit to the previous screen without saving 19 FUEL MANAGER 2 FUEL MANAGER SET TOTAL AMOUNT OF FUEL LIGHTING f RESET FUEL USED YES IJ FUEL MANAGER RESET AVG RATE YES D9 SYSTEM SETUP MPH FT UNITS i E TOTTI MES lt 7 gt T 2 45 Save Changes YES NO RESET TRIP YES IJ STOP Your fuel tanks must be activated and set to the proper capacity before the fuel manage
16. ation pad to highlight the Antares Menu Screen ER on the screen indicator bar located at the bottom of the screen Then use the down arrow on the navigation pad to scroll down to SYSTEM SETUP and press a LIGHTING Use the ALU pad to highlight SYSTEM SETUP then press FUEL MANAGER SYSTEM SETUP Step 1 INPUT SETUP TANK SETUP Use the navigation pad to highlight INPUT SETUP then DEPTH SETUP press INPUT SETUP Input Setup will allow you select which analog senders are connected to your Antares unit To activate or deactivate a sender use the left or right navigation buttons to select either TANK 1 TANK 2 TRIM TANK 3 AIR TEMP or SPEED SOURCE Once the desired selection 1s highlighted press D Now use the the up or down navigation buttons to highlight the desired setting then press aD The MJ icon on the Save Changes bar will automatically highlight If your changes are correct press gt to save SAVED will appear to confirm that changes have been saved If the changes are not correct use the navigation pad to highlight US and press aD NOT SAVED will appear to confirm that the changes have not been saved Refer to the list of available INPUTS on the next page for further instructions For sender connection information refer to wiring diagram HN0605 in Part VI pg 36 for further information INPUT SETUP TANK 1 SELECT SENDER TYPE EURO NONE Save Changes YES NO DDECC Cos
17. been saved If the changes are not correct use the navigation pad to highlight US and press aD NOT SAVED will appear to confirm that the changes have not been saved Once you have saved all the appropriate settings press ED to return to the SYSTEM SETUP menu YOU ARE NOW FINISHED WITH THE SETUP PROCESS PRESS amp To RETURN TO THE MAIN MENU SCREEN SIMPLY USE THE NAVIGATION PAD TO MOVE YOUR WAY THROUGH THE ANTARES DISPLAY SCREENS YOU ARE NOW READY TO HEAD OUT ON TO THE WATER Part III Operating Instructions Your Faria Antares unit has 8 main display screens and an optional Radio Control Screen When a screen 1s selected the Screen Indicator Icon on the Screen Indicator Bar located at the bottom of the screen will be highlighted Use the right or left arrows on the navigation pad to scroll through the available display screens To activate the optional Radio Control Screen press the E button 1f available SCREEN INDICATOR ICONS MENU SCREEN GAUGE SCREEN 1 GA GAUGE SCREEN 2 EB QUICK VIEW SCREEN FUEL FLOW MANAGER SCREEN DEPTH AIR TEMP WATER TEMP SCREEN CI TANK S LEVEL SCREEN GPS GPS SCREEN GAUGE SCREEN 1 GAUGE SCREEN 2 Depth 28 6 Ft Bearing 235 Eng Hrs 9999 Throttle 100 N Gauge Screen 1 and Gauge Screen 2 provide a quick glance at up to 12 different gauge functions Each quadrant can be customized to display any piece of information available To cu
18. consequential damage caused by product defects Some states do not allow the exclusion or limitation of consequential damages so the above may not apply to you Ihe Warranty herein is in lieu of any other expressed warranty of merchantability or fitness or any other obligation on the part of Faria Marine Instruments the Thomas G Faria Corporation or the seller All implied warranties are limited to the initial 36 month period Some states do not allow limitation on how long an implied warranty lasts so the above limitation may not apply to you This warranty gives you specific legal rights and you also have other rights which vary from state to state These fees are in effect as of 08 17 2007 and are subject to change without notice PO Box 983 Uncasville CT USA 06382 0983 Tel 860 848 9271 Fax 860 848 2704 Customer Service 800 473 2742 www faria instruments com for gauges beyond initial warranty period Fog Resistant Lens Only 2 inch instruments 2 inch Clock or Hourmeter 2 inch Warning System Indicator 2 inch Honda Trim Digital Depth Sounder Fuel Flow Manager Flux Gate Compass Flux Gate Compass with Sensor Speedometer or Water Pressure gauge Electronic Speedometer with sensor Tachometer Synchronizer or Electronic Speedometer Tachometer with Hourmeter or System Indicator Pilot Speedometer or Tachometer Commander Tachometer or Speedometer Multifunction Instrument MG2000 Speedo
19. isplay N A For Air Temperature an analog Air Temperature sender must be installed If no sender is installed then the Air quadrant will display N A Refer to your boat owner s manual to determine which transducers are installed on your boat 14 TANK LEVEL SCREEN CI TANK 1 19 mn The tank level screen will display tank level information as reported by the tank s level sender Your Antares unit can display level information for up to three tanks Tanks must be activated during the setup process to be displayed on this screen See Part II System Setup for more information on tank setup Dual Tank Display Three Tank Display TANK 1 75 TANK 1 75 Moa Er E F TANK 2 72 MA gt TANK 2 72 E F TANK 3 73 E F E E F 15 GPS SCREEN GPS coG coG O O 19 Mag O True 0 True No Mag Signal AT N41926 13 AT N41 2613 LO LON o N 4 Fr N W72 6 27 W72 6 27 Magnetic North Signal Available No Magnetic North Signal Available The GPS Screen will display COG Latitude and Longitude when a NMEA0183 GPS Antenna is installed You do not need to change any settings when installing a GPS antenna Your Antares unit will automatically recognize if a compatible GPS antenna 1s connected When the GPS signal is acquiring the Antares will display ACQUIRING GPS If no GPS antenna s installed then NO GPS will appear COG COG O O 0 Acquiring GPS 0 No GPS No Mag Signa
20. l No Mag Signal Ei Acquiring GPS LAT No GPS LON LON Acquiring GPS No GPS Acquiring GPS Signal GPS not connected Refer to your boat owner s manual to determine if a NMEA0183 GPS antenna has been installed with the Faria Antares system For full details regarding Magnetic and True North GPS readings visit NOAA s National Geophysical Data Center website http www ngdc noaa gov seg geomag declination shtml 16 RADIO CONTROL SCREEN VOLUME gt MUTE MODE BAND SEEK TUNE 4 SHIFT SCAN HO EB PRESS ESCTO EXIT To enter the Radio Control Screen press the gt button The Radio Control Screen allows you to control certain functions of your boat s Jensen radio This option 1s not available on all Antares models and requires a compatible Jensen radio For a list of compatible radios visit www faria instruments com antares html Press up or down on the navigation button to scroll through the various radio control functions Then press left right or Gu to adjust the highlighted control function Press dD to turn radio on off VOLUME Press right or left on the navigation button to increase decrease volume u IE Press ENTER to activate Mute Press again to deactivate MODE Press right on the navigation button to change radio mode Ex BAND Press right on the navigation button to change band Ex FMI FM2 SAT SEEK TUNE Press right or left on the navig
21. meter or Tachometer Serial Bus Gateway Box 10 00 15 00 30 00 35 00 35 00 55 00 90 00 75 00 140 00 15 00 50 00 30 00 50 00 125 00 125 00 40 00 175 00 400 00 IS0090F 8 2007 ecr7049
22. prop still in water then press Step 3 Set your engine to the top of its trailer full up position then press PRESS ENTER D TRIM E CALIBRATE TRIM Once step 3 is completed the screen will display TRIM CALIBRATION COMPLETE and the icon on the Save Changes bar will automatically highlight If ALL steps were followed correctly press TRIM to save SAVED will appear to confirm that the changes have been saved If ALL steps were not followed correctly use the Seve changes vesino navigation pad to highlight US and press aD NOT SAVED will appear to confirm that the changes have not been saved u The Antares will automatically return to the previous screen 25 SELF TEST Le CALIBRATE SCANNING SELF TEST MASTER RESE HE _ TEST SUCCESFULL DIAGNOSTICS Y MED T e Your Faria Antares will automatically run a self diagnostics test when this menu option is selected The test may take up to 3 minutes If no problems are found the screen will display TEST SUCCESSFUL If a problem is found the screen will display Error s Found If this occurs contact Faria Customer Service Refer to Part VIII Warranty for further information After running the self diagnostics test the Antares will automatically return to the Main Menu screen 26 MASTER RESET a CALIBRATE SELF TEST MASTER RESET DIAGNOSTICS gt a TP B ARE YOU
23. r will become functional Refer to Part II SYSTEM SETUP for further information It is CRITICAL that you correctly set the TOTAL AMOUNT OF FUEL each time you refuel Total Amount of Fuel Fuel Added Fuel Remaining Use the up or down navigation buttons to highlight the desired setting then use the left or right navigation buttons to change the value of the highlighted area You can make changes to all of the Fuel Manager options before saving Once all the changes have been properly set press aD The MS icon on the Save Changes bar will automatically highlight If your changes are correct press dD to save SAVED will appear to confirm that changes have been saved If the changes are not correct use the navigation pad to highlight LS and press aD NOT SAVED will appear to confirm that the changes have not been saved Note The TOTAL AMOUNT OF FUEL must be set to the proper value to insure accurate performance from the Fuel Manager 20 SYSTEM SETUP EN LIGHTING FUEL MANAGER SYSTEM SETUP UNITS Y Refer to Part II System Setup pages 6 9 for detailed information 21 UNITS o l UNITS LIGHTING P FLUIDS PRESSURE O GAL O PSI O LITERS O BAR FUEL MANAGER DEPTH TEMP O FEET F1 O FARENHEIT O METERS M O CELCIUS SYSTEM SETUP orartoms SPEED DISTANCE MPH FT MPH MILES UNITS RPM GAL O Km h O KILOMETERS O KNOTS O Naut MILES Ka Save Change
24. s YES NO The Units screen will allow you to change the display values for Fluids Pressure Depth Temperature Speed and Distance Use the left or right navigation buttons to highlight the desired option to change then use the up or down navigation buttons to change the value located directly below the highlighted option You can make changes to all of the listed options before saving Once all the changes have been properly set press aD The icon on the Save Changes bar will automatically highlight If your changes are correct press SAVED to save will appear to confirm that the changes have been saved Ifthe changes are not correct use the navigation pad to highlight LS and press aD NOT SAVED will appear to confirm that the changes have not been saved 22 CALIBRATE CALIBRATE lt SPEEDO CAL SELF TEST MASTER RESET DIAGNOSTICS TRIM CAL Your Faria Antares unit is factory cal brated to give you optimal performance with the senders installed on your boat In order to further insure that you are getting the most accurate readings possible we have made the following cal brations available to you To adjust your speedometer calibration or trim calibration use the up or down navigation buttons to highlight the desired option then press aD 23 SPEEDOMETER CALIBRATION SPEED CALIBRATION PRESS ENTERTO PADDLEWHEEL GPS 13 8 15 0 MPH MPH SPEED CALIBRATIO
25. stomize a quadrant press aD The upper left quadrant will be highlighted yellow as pictured below Now use the navigation pad to select the quadrant you wish to change When the desired Bearing 235 T quadrant is highlighted press aD A list of options will appear in the center of the screen Use the up or down arrows on the navigation pad to highlight the desired information to be displayed then press aD The highlighted quadrant will change to the selected display Once you have set all of the quadrants to the desired information press ED to return to Depth 28 6 Ft Bearing 235 7 Depth 28 6 Ft Bearing 235 r CS DIGITAL DEPTH DIGITAL COG DIGITAL TACH DIGITAL SPEED DIGITAL TANK 1 DIGITAL TANK 2 DIGITAL TANK 3 the normal operating mode 11 QUICK VIEW SCREEN 22 13 5 MPH RPM Total Fuel Remaining Depth COG The Quick View screen provides a large digital display for quick easy reading Use the up or down navigation buttons to scroll through the available information 2013 Speed Total Fuel Remaining Depth coG LATT gt 0 0 GAL Speed RPM nn nn nn mn na mn Total Fuel Remainino Depth COG E T lt P gt 28 6 FEET Speed RPM Total Fuel Remaining Deh E T T 15 Mag Speed RPM Total Fuel Remaining Depth 12 FUEL FLOW MANAGER SCREEN Inst Rate W Trip Total Remaining 90 GAL Mib
26. the Save Changes bar will automatically highlight If your changes are correct press aD to save SAVED will appear to confirm that the changes have been saved If the changes are not correct use the navigation pad to highlight US and press aD NOT SAVED will appear to confirm that the changes have not been saved Once you have saved all the appropriate settings press EY to return to the SYSTEM SETUP menu Step 3 Depth Setup TANK SETUP Use the navigation pad to highlight DEPTH SETUP then DEPTH SETUP INPUT SETUP press Depth Setup will allow you to set the shallow water alarm set the deep water alarm and set the keel offset Note A digital depth transducer must be installed on your boat for the depth option to work Refer to your owner s manual to determine if there is a transducer installed Your Antares will automatically recognize if a compatible digital depth sounder is installed DEPTH SETUP SHALLOW WARNING 123 4 Ft DEEP WATER ALARM 123 4 Ft KEEL OFFSET 4 123 4 D Ft Save Changes YES NO Use the up or down arrows on the navigation pad to highlight the desired option then use the left or right arrows on the navigation pad to make the appropriate changes Once you have adjusted all the options to the desired settings press aD The icon on the Save Changes bar will automatically highlight If your changes are correct press P to save SAVED will appear to confirm that the changes have
Download Pdf Manuals
Related Search