Extron electronic Extron Electronics Switch MTP R AV User's Manual
Contents
1. unbalanced stereo audio input or mono output Wire the connector as shown gan Do not tin the wires CAUTION p For unbalanced audio connect NO aaa ral the sleeve s to the ground contact Ti p DO NOT connect the sleeve s to NO Ground Here th tive contacts AAEE ne Unbalanced Mono Output Balanced Mono Output NOTE These boards do not have a jumper to set for stereo audio output Audio output is always mono RJ 45 T568A T568B 10 Either connect the output RJ 45 on the u in wre anor Wire color MTP T AV to an MTP receiver using CAT 5 5e 12345678 ee 3 White orange White green 5 White blue White blue or 6 cable or connect the input RJ 45 on the wn MTP R AV board with an output cable to a suitable MTP transmitter Terminate the cable as shown on peer Ie range reen the right using the same standard 7 white brown White brown T568A or T568B at both ends ry Brown Brown 11 Image sharpness and gain MTP R AV only can be Insert Twisted adjusted with the two front panel rotary encoders 70 for optimizing the image and signal quality View the image and adjust the either control for the best image quality PowerCage Front Panel The following PowerCage enclosure front panel features are relevant to the installation and operation of the MTP T AV and MTP R AV boards NOTE The MTP T AV and MTP R AV boards are not configurable and the Power LED slots 1 16 This2. LED lights to indicate that power is applied to the selected board Temperature LED This LED lights if the temperature within Ma e e 0 0 9 0 the PowerCage enclosure is high i anescage es approximately 167 F 75 C and PowerCage Comm port feature does not work with the MTP boards equipment damage is imminent For full installation and operating details of the PowerCage refer to the PowerCage 1600 Enclosure User Guide available at www extron com Extron USA West Extron USA East Extron Europe Extron Asia Extron Japan Extron China Extron Middle East Headquarters q 800 633 9876 800 3987 6673 800 7339 8766 81 3 3511 7655 400 883 1568 971 4 2991800 800 633 9876 Inside USA Canada Only Inside Europe Only Inside Asia Only 81 3 3511 7656 FAX Inside China Only 971 4 2991880 FAX Inside USA Canada Only 68 1643 50 1 919 863 1794 31 33 453 4040 65 6383 4400 86 21 3760 1568 1 714 491 1500 1 919 863 1797 FAX 31 33 453 4050 FAX 65 6383 4664 FAX 86 21 3760 1566 FAX RevA 1 714 491 1517 FAX 08 10 2010 Extron Electronics All rights reserved www extron com 2
3. PowerCage MTP T AV and MTP R AV Board Setup Guide The Extron PowerCage MTP T AV and MTP R AV are twisted pair transmitters and receivers in a modular board format for the PowerCage 1600 modular enclosure They transmit or receive composite video or S video and audio over CAT 5 type cable Both boards can be used with any CAT 5 5e or 6 cable or Extron Enhanced Skew Free A V UTP cable for cable runs up to 1000 feet 300 m The boards mount in any of the 16 expansion slots at the rear of the PowerCage 1600 Refer to the PowerCage MTP T AV and MTP R AV User Guide and the PowerCage 1600 Enclosure User Guide available at www extron com a us do 28 2 iG ce OHO N U o fal U N o N U a YID MONO AUDIO OUTPUT AUDIO INPUT tR AARAA SHARP GAIN 4 2 OS e CI NOTE The hot swappable modular design allows for replacing or O 2090 upgrading boards in the field at any time without having to power down the system MTP R AV MTP T AV Installation 1 Select an open slot at the rear or take out a blank plate by loosening the two screws top and bottom and lifting the blank away NOTE Ifa board is already in the slot loosen the screws and remove the board 2 2 Remove the new board from the box holding the board by the frame Z 3 Hold the board with the signal connectors 16 Available Single Board Slots or gt lt towards y
4. ou and the MTP AV board name eee eee and LED at the top and align the top and bottom grooves of the board with the slide posts in the selected enclosure slot ria CE Ss i Supply Z eZ 3 te 5 4 Carefully slide the board into the slot As Co Ko aligning that the two tabs on the lower AA A Align board and i r A N rA ide int t front end of the board with the matching d a l gt 9 000 20 e S amp ports in the enclosure Push the board 29 gt J2 P AE firmly into place 2 a E Ss P 0 X 5 Tighten the screws to secure the board P Screws 2 per board 6 If applicable repeat steps 1 through 5 for any other modular boards NOTE Cover all empty board slots do not leave them open Using a tool securely fasten the screws for boards and blank panels after initial installation and subsequent removal and replacement of the boards 7 If power has been removed reconnect and power on the PowerCage The LED on the board lights green and the new board is auto detected J 8 Following the image at right connect input or output S video OR device cables to the the two BNC connectors for S video signals or for composite video signals x Composite Video Continued on side 2 1 PowerCage MTP T AV and MTP R AV Board Setup Guide cont d 9 Insert a 5 pole captive screw connector into the captive screw audio input or output connector for balanced or
Download Pdf Manuals
Related Search