Extron electronic Extron Electronics Switch BBG 6 A J User's Manual
Contents
1. j FE Introduction The BBG 6 A and BBG 6 AJ an exclusively Japanese model are compact high performance blackburst color bars and audio generators Unless otherwise noted the name BBG 6 A refers to both the standard USA and European countries and the Japanese models within this guide The BBG 6 A provides six broadcast quality blackburst signal outputs on BNC connectors two of which can be changed to color bars with a DIP switch For the standard BBG 6 A the user can select output signals as either NTSC or PAL The BBG 6 AJ outputs NTSC only and has no setup pedestal in its video output Color bars are standard SMPTE bars NTSC or full field PAL The audio generator provides a single 1 kHz sine wave audio tone either balanced or unbalanced with a selectable output level of either 4 dBu pro or 10 dBV consumer The BBG 6 A is a member of the VersaTools line of basic distribution amplifiers switchers and video accessories The unit ships2. sr AE H Bk BE e j e X ATF JPR VARS F
3. 10 dBV audio level with unbalanced wiring NTSC RESERVED Blackburst Blackburst 10 PAL Color bars Color bars BBG 6 A BBG6AJ Figure 5 BBG 6 A and BBG 6 A J DIP switches Nolia DIP switch 2 of the BBG A J is not used Mol Please refer to the table below for other combinations Unbalanced 4dBV 10dBV Dip Switch Position o aue BBG 6 A Connections Indicators and Controls 5 Connections Indicators and Controls Audio output connector Insert a 3 5 mm 5 pole captive screw connector into this connector for a balanced or unbalanced 1 kHz sine wave audio tone Do not tin the stripped power supply leads before installing the captive screw connector Tinned wires are not as secure in the captive screw connectors and could pull out CAUTION A For unbalanced audio connect the sleeve s to the ground contact DO NOT connect the sleeve s to the negative contacts 3 16 5 mm MAX q Tip Co sw 2 NO Ground Here G Sleeve S CC Hm a 5 Sleeve s Cw Tip Oo Ring gt Tip NO Ground Here CT J Balanced Output Unbalanced Output Figure 6 BBG 6 audio wiring 6 Power connector Plug the external 12 V power supply into this 2 pole captive screw connector The power supply is included with the unit Figure 7 shows how to wire
4. 16 screws in opposite diagonal corners to secure the BBG 6 A to the shelf Install blank panel s or other unit s to the rack shelf 4 Insert the shelf into the rack aligning the holes in the shelf with those of the rack 5 Secure the shelf to the rack using the supplied machine screws The VersaTools shelf can be mounted in the front or in the rear of the rack BBG 6 A Installation Figure 2 Mounting the BBG 6 A on a standard shelf Furniture or projector mounting Furniture mount or projector mount the unit using the optional mounting kit part 70 212 01 for furniture or 70 217 04 for a projector as follows 1 Ifrubber feet were previously installed on the bottom of the unit remove them 2 Attach the mounting brackets to the BBG 6 A with the machine screws provided figure 3 3 For furniture mounting hold the unit with the attached brackets against the underside of the table or other furniture Mark the location of the screw holes of the bracket on the mounting surface Projector Mounting Bracket v Under Desk Mounting Projector Mounting Projector Figure 3 Desk and projector mounting the BBG 6 A BBG 6 A Installation 3 Installation 4 4 For furniture mounting drill 3 32 2 mm diameter pilot holes 1 4 6 3 mm deep in the mounting surface at the marked screw locations 5 For furniture mounting insert 8 wood screws into the four pilot holes Tigh
5. for all levels 3 Signal frequency we 1 kHz NOTE 0 dBu 0 775 V 0 dBV 1 V 0 dBVx 2 dBu 8 BBG 6 A Specifications Parts and Accessories BBG 6 A Specifications Parts and Accessories 9
6. A E RS 170A standard for NTSC 3 58 CCIR 624 4 standard for PAL BBG 6 A ee RS 170A standard for NTSC 3 58 in 75 ohms Sync level BBG O Asrori 40 IRE for NTSC 43 IRE for PAL BBG 6 A Je 40 IRE for NTSC Color burst level BBG O Asner 40 IRE for NTSC 43 IRE for PAL BBG 6 A Dsesseeteedescumn 40 IRE for NTSC Setup level BBG O Aroi 7 5 IRE NTSC or 0 IRE PAL BBG 6 A Je 0 IRE NTSC Tolerance for all levels 3 Subcarrier levels BBG 0 Dm NTSC 3 579545 3 Hz PAL 4 433618 3 Hz BB OA Jonines NTSC 3 579545 3 Hz BBG 6 A Specifications Parts and Accessories 7 Specifications Part Numbers and Accessories Color Bars output General Number signal type External power supply 100 VAC to 240 VAC 50 60 Hz 2 5 watts BBG b E 2 color bars switchable standard external autoswitchable to 12 VDC SMPTE bars for NTSC 1 A regulated power supply full field 8 bar for PAL Power input requirements 12 VDC 0 2 A max BBG OA Standard SMPTE bars for NTSC Temperature humidity Storage 40 to 158 F 40 t 70 C CODIBIGOLOE Base EPI HM 2 BNC female 10 to 90 noncondensing Bes uda Operating 32 to 122 F 0 to 50 C BBG 6 As NTSC 3 58 PAL E i a d Nd cried ACK MOUN nn es with optiona ersalools 3 dee NTSC 3 58 dci da t 60 190 20 RSF 123 or E 75 ohms 60 604 20 RSB 123 or Universal 9 5 Sync level deep rack shelf part 60 190 01 RS
7. Ae Extron Electronics USA Extron Electronics Europe Extron Electronics Asia by gt 1230 South Lewis Street Beeldschermweg 6C 135 Joo Seng Rd 04 01 J 4 Anaheim CA 92805 3821 AH Amersfoort The Netherlands PM Industrial Bldg Singapore 368363 ryn 800 633 9876 714 491 1500 800 3987 6673 31 33 453 4040 800 7339 8766 65 6383 4400 www extron com FAX 714 491 1517 FAX 31 33 453 4050 FAX 65 6383 4664 2006 Extron Electronics All rights reserved Extron Electronics Japan Kyodo Building 16 Ichibancho Chiyoda ku Tokyo 102 0082 Japan 81 3 3511 7655 FAX 81 3 3511 Extron Electronics 5o INTERFACING SWITCHING AND DISTRIBUTION ec now User s Guide BBG 6 A BLACKBURST AND AUDIO GENERATOR BLACKBURST BBG 6 A and BBG6A J Blackburst Color Bars Audio Generator 68 712 01 Rev D 11 06 Precautions Safety Instructions English This symbol is intended to alert the user of important operating and maintenance servicing instructions in the literature provided with the equipment This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product s enclosure that may present a risk of electric shock Caution Read Instructions Read and understand all safety and operating instructions before using the equipment Retain Instructions The safety instructions should be kept for future reference Follow Warnings Follow all warnings and instruct
8. U 129 BBG 6 p PE TN 40 IRE for NTSC 43 IRE for PAL or 60 604 01 RSB 129 Also under desk BBG 6 A J eise th eredi 40 IRE for NTSC mountable with optional MBU 123 kit Color burst level part 70 212 01 BBG OA M 40 IRE for NTSC 43 IRE for PAL BHCIOSIBS ype seen Metal BBG 6 A Je 40 IRE for NTSC Enclosure dimensions 1 7 Hx 4 3 W x 3 0 D Setup level 1U high quarter rack wide 4 3 cm H x 10 9 cn W x 7 6 cm D BBG OA NTSC 7 5 IRE PAL 0 IRE Depth excludes connectors BBG 6 A J eee NTSC 0 IRE Product Weight se 0 4 Ibs 0 2 kg White level om ni 100 IRE Shipping weight es 3 Ibs 2 kg Tolerance for all levels 3 ISTA 1A in carton Subcarrier levels International Safe Transit Association BBG 6 c NTSC 3 579545 3 Hz PAL 4 433618 3 Hz UL CUL BPG ON on NTSC 3 579545 3 Hz no setup pedestal Compliances eee CE FCC Class A VCCI AS NZS ICES _ DD Ee a EEA E 30 000 hours Audio output VAE ea a 3 years parts and labor Number signal type sesesseszsines 1 set L and R of stereo sine waves balanced or unbalanced All nominal levels are at 10 Connectors pp 1 3 5 mm captive screw connector 5 pole DE l PERANGE ee end on 50 ohms unbalanced 100 ohms balanced Specifications are subject to change without notice DIC Ie NOY Cl mem em Selectable professional level 4 dBu 1 23 V balanced or consumer level 10 dBV 316 mV unbalanced TAP de b dieti tu NUS 0 196 Tolerance
9. de la pared Protecci n del cables de alimentaci n Los cables de alimentaci n el ctrica se deben instalar en lugares donde no sean pisados ni apretados por objetos que se puedan apoyar sobre ellos Reparaciones mantenimiento Solicitar siempre los servicios t cnicos de personal calificado En el interior no hay partes a las que el usuario deba acceder Para evitar riesgo de electrocuci n no intentar personalmente la reparaci n mantenimiento de este equipo ya que al abrir o extraer las tapas puede quedar expuesto a voltajes peligrosos u otros riesgos Ranuras y aberturas Si el equipo posee ranuras o orificios en su caja alojamiento es para evitar el sobrecalientamiento de componentes internos sensibles Estas aberturas nunca se deben obstruir con otros objetos Bater a de litio Existe riesgo de explosi n si esta bater a se coloca en la posici n incorrecta Cambiar esta bater a nicamente con el mismo tipo o su equivalente recomendado por el fabricante Desachar las bater as usadas siguiendo las instrucciones del fabricante FCC Class A Notice Note This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed a
10. es gefahrliche Spannungen dienichtisoliert sind und die einen elektrischen Schock verursachen k nnen herrschen Achtung Lesen der Anleitungen Bevor Sie das Ger t zum ersten Mal verwenden sollten Sie alle Sicherheits und Bedienungsanleitungen genau durchlesen und verstehen Aufbewahren der Anleitungen Die Hinweise zur elektrischen Sicherheit des Produktes sollten Sie aufbewahren damit Sie im Bedarfsfall darauf zur ckgreifen k nnen Befolgen der Warnhinweise Befolgen Sie alle Warnhinweise und Anleitungen auf dem Ger t oder in der Benutzerdokumentation Keine Zusatzgerate Verwenden Sie keine Werkzeuge oder Zusatzger te die nicht ausdr cklich vom Hersteller empfohlen wurden da diese eine Gefahrenquelle darstellen k nnen Instrucciones de seguridad Espanol Este s mbolo se utiliza para advertir al usuario sobre instrucciones importantes de operaci n y mantenimiento o cambio de partes que se desean destacar en el contenido de la documentaci n suministrada con los equipos Este s mbolo se utiliza para advertir al usuario sobre la presencia de elementos con voltaje peligroso sin protecci n aislante que puedan encontrarse dentro de la caja o alojamiento del producto y que puedan representar riesgo de electrocuci n Precaucion Leer las instrucciones Leer y analizar todas las instrucciones de operaci n y seguridad antes de usar el equipo Conservar las instrucciones Conservar las instruccione
11. ions marked on the equipment or in the user information Avoid Attachments Do not use tools or attachments that are not recommended by the equipment manufacturer because they may be hazardous Consignes de S curit Francais Ce symbole sert avertir l utilisateur que la documentation fournie avec le mat riel contient des instructions importantes concernantl exploitation et la maintenance r paration Ce symbole sert avertir l utilisateur de la pr sence dansle boitier del appareil de tensions dangereuses non isol es posant des risques d lectrocution Attention Lire les instructions Prendre connaissance de toutes les consignes de s curit et d exploitation avant d utiliser le mat riel Conserver les instructionse Ranger les consignes de s curit afin de pouvoir les consulter l avenir Respecter les avertissements Observer tous les avertissements et consignes marqu s sur le mat riel ou pr sent s dans la documentation utilisateur Eviter les pi ces de fixation Ne pas utiliser de pi ces de fixation ni d outils non recommand s par le fabricant du mat riel car cela risquerait de poser certains dangers Sicherheitsanleitungen Deutsch Dieses Symbol soll dem Benutzer in der im Lieferumfang enthaltenen Dokumentation besonders wichtige Hinweise zur Bedienung und Wartung Instandhaltung geben DiesesSymbolsoll den Benutzer darauf aufmerksam machen da im Inneren des Geh uses dieses Produkt
12. ked by other objects Lithium battery There is a danger of explosion if battery is incorrectly replaced Replace it only with the same or equivalent type recommended by the manufacturer Dispose of used batteries according to the manufacturer s instructions Avertissement Alimentations Ne faire fonctionner ce mat riel qu avec la source d alimentation indiqu e sur l appareil Ce mat riel doit tre utilis avec une alimentation principale comportant un fil de terre neutre Le troisieme contact de mise la terre constitue un dispositif de s curit n essayez pas de la contourner ni de la d sactiver D connexion de l alimentation Pour mettre le mat riel hors tension sans danger d connectez tous les cordons d alimentation de l arri re de l appareil ou du module d alimentation de bureau s il est amovible ou encore de la prise secteur Protection du cordon d alimentation Acheminer les cordons d alimentation de mani re ce que personne ne risque de marcher dessus et ce qu ils ne soient pas cras s ou pinc s par des objets R paration maintenance Faire ex cuter toutes les interventions de r paration maintenance par un technicien qualifi Aucun des l ments internes ne peut tre r par par l utilisateur Afin d viter tout danger d lectrocution l utilisateur ne doit pas essayer de proc der lui m me ces op rations car l ouverture ou le retrait des couvercles risquent de l exposer de hautes te
13. n Komponenten des Ger tes sind wartungsfrei Zur Vermeidung eines elektrischen Schocks versuchen Sie in keinem Fall dieses Ger t selbst ffnen da beim Entfernen der Abdeckungen die Gefahr eines elektrischen Schlags und oder andere Gefahren bestehen Schlitze und ffnungen Wenn das Ger t Schlitze oder L cher im Geh use aufweist dienen diese zur Vermeidung einer Uberhitzung der empfindlichen Teile im Inneren Diese Offnungen d rfen niemals von anderen Objekten blockiert werden Litium Batterie Explosionsgefahr falls die Batterie nicht richtig ersetzt wird Ersetzen Sie verbrauchte Batterien nur durch den gleichen oder einen vergleichbaren Batterietyp der auch vom Hersteller empfohlen wird Entsorgen Sie verbrauchte Batterien bitte gemaf den Herstelleranweisungen Advertencia Alimentaci n el ctrica Este equipo debe conectarse nicamente a la fuente tipo de alimentaci n el ctrica indicada en el mismo La alimentaci n el ctrica de este equipo debe provenir de un sistema de distribuci n general con conductor neutro a tierra La tercera pata puesta a tierra es una medida de seguridad no puentearia ni eliminaria Desconexi n de alimentaci n el ctrica Para desconectar con seguridad la acometida de alimentaci n el ctrica al equipo desenchufar todos los cables de alimentaci n en el panel trasero del equipo o desenchufar el m dulo de alimentaci n si fuera independiente o desenchufar el cable del recept culo
14. nd used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Note This unit was tested with shielded cables on the peripheral devices Shielded cables must be used with the unit to ensure compliance Extron s Warranty Extron Electronics warrants this product against defects in materials and workmanship for a period of three years from the date of purchase In the event of malfunction during the warranty period attributable directly to faulty workmanship and or materials Extron Electronics will at its option repair or replace said products or components to whatever extent it shall deem necessary to restore said product to proper operating condition provided that it is returned within the warranty period with proof of purchase and description of malfunction to USA Canada South America and Central America Extron Electronics Beeldschermweg 6C 1001 East Ball Road 3821 AH Amersfoort Anaheim CA 92805 USA The Netherlands Europe Africa and the Middle Fast Extron Electronics Europe Asia Japan Extron Electronics Asia Extron Electronics Japan 135 Joo Seng Road 04 01 Kyodo Building PM Industrial Bldg 16 Ichibancho Singapore 368363 Chiyoda ku Tokyo 102 0082 Japan This Limited Warranty does not appl
15. nsions et autres dangers Fentes et orifices Si le boitier de l appareil comporte des fentes ou des orifices ceux ci servent emp cher les composants internes sensibles de surchauffer Ces ouvertures ne doivent jamais tre bloqu es par des objets Lithium Batterie Il a danger d explosion s ll y a remplacment incorrect de la batterie Remplacer uniquement avec une batterie du meme type ou d un ype equivalent recommande par le constructeur Mettre au reut les batteries usagees conformement aux instructions du fabricant Vorsicht Stromquellen Dieses Ger t sollte nur ber die auf dem Produkt angegebene Stromquelle betrieben werden Dieses Ger t wurde f r eine Verwendung mit einer Hauptstromleitung mit einem geerdeten neutralen Leiter konzipiert Der dritte Kontakt ist f r einen Erdanschlu amp und stellt eine Sicherheitsfunktion dar Diese sollte nicht umgangen oder aufer Betrieb gesetzt werden Stromunterbrechung Um das Ger t auf sichere Weise vom Netz zu trennen sollten Sie alle Netzkabel aus der R ckseite des Ger tes aus der externen Stomversorgung falls dies m glich ist oder aus der Wandsteckdose ziehen Schutz des Netzkabels Netzkabel sollten stets so verlegt werden daf sie nicht im Weg liegen und niemand darauf treten kann oder Objekte darauf oder unmittelbar dagegengestellt werden k nnen Wartung Alle Wartungsmafsnahmen sollten nur von qualifiziertem Servicepersonal durchgef hrt werden Die interne
16. s de seguridad para futura consulta Obedecer las advertencias Todas las advertencias e instrucciones marcadas en el equipo o en la documentaci n del usuario deben ser obedecidas Evitar el uso de accesorios No usar herramientas o accesorios que no sean especificamente recomendados por el fabricante ya que podrian implicar riesgos Warning Power sources This equipment should be operated only from the power source indicated on the product This equipment is intended to be used with a main power system with a grounded neutral conductor The third grounding pin is a safety feature do not attempt to bypass or disable it Power disconnection To remove power from the equipment safely remove all power cords from the rear of the equipment or the desktop power module if detachable or from the power source receptacle wall plug Power cord protection Power cords should be routed so that they are not likely to be stepped on or pinched by items placed upon or against them Servicing Refer all servicing to qualified service personnel There are no user serviceable parts inside To prevent the risk of shock do not attempt to service this equipment yourself because opening or removing covers may expose you to dangerous voltage or other hazards Slots and openings If the equipment has slots or holes in the enclosure these are provided to prevent overheating of sensitive components inside These openings must never be bloc
17. ten each screw into the mounting surface until just less than 1 4 6 3 mm of the screw head protrudes 6 Forfurniture mounting align the mounting screws with the slots in the brackets and place the unit against the surface with the screws through the bracket slots 7 For furniture mounting slide the unit slightly forward or back then tighten all four screws to secure the unit in place 8 For projector mounting secure the unit to a projector mount or other surface by inserting the mounting bolt through the bracket s slotted hole Connections Indicators and Controls See figure 4 below Power Signal indicator LED When illuminated this LED indicates that the BBG 6 A is receiving power Blackburst only outputs Connect up to four display devices to these BNC connectors for blackburst output Blackburst color bars outputs Connect up to two display devices to these BNC connectors for blackburst or color bars output BECCA BLACKBURST AND AUDIO GENERATOR Figure 4 BBG 6 A front and rear panels BBG 6 A Installation 2 DIP switch Use these DIP switches to select between 4 dBu pro or 10 dBV consumer audio output level between NTSC or PAL USA only output and between blackburst or color bars for outputs 1 and 2 With the first DIP switch set to 4 the unit outputs 4 dBu audio level with balanced wiring With the DIP switch set to 10 the unit outputs
18. the connector When connecting the power supply voltage polarity is extremely important Applying power with incorrect voltage polarity could damage the power supply and the BBG 6 A Identify the power cord negative lead by the ridges on the side of the cord or the black heat shrink wrapping around it 3 16 5 mm MAX A EE E E X m S Ge E SECTION A A 12V Power Supply Captive Screw Output Cord Connector Figure 7 Power connector wiring Do not tin the stripped power supply leads before installing the captive screw connector Tinned wires are not as secure in the captive screw connectors and could pull out EZENN The two power cord wires must be kept separate while the power supply is plugged in Remove power before continuing 6 BBG 6 A Connections Indicators and Controls To verify the polarity before connection plug in the power supply with no load and check the output with a voltmeter As an alternative you can use an Extron P S 100 Universal 12 VDC Power Supply part 60 357 01 which can power up to ten BBG 6 As or other Extron 12 VDC devices using only one AC power connector O Version label Differentiates the standard NTSC and PAL signals versus Japanese BBG 6 A J NTSC signals only versions of the BBG 6 A Specifications Blackburst output Number signal Fy PC susce sten 6 blackburst two can be switched to color bars COonnectors sant en de 6 BNC female Standards BBG 6
19. with an external desktop 12 V power supply which accepts 100 240 VAC input Models There are two available models of the BBG 6 A BBG 6 A NTSC and PAL signal Handles NTSC and PAL signals This version is used in the USA and some other countries BBG 6 A J NTSC signal only Handles NTSC signals only This version is used in Japan Other than their differing signal options these two models are identical Installation The BBG 6 A can be mounted on a rack shelf VersaTools or universal under a desk or tabletop or on a projector bracket Rack mounting For optional rack mounting mount the BBG 6 A on a VersaTools 19 1U Rack Shelf Extron part 60 190 20 or 60 604 20 figure 1 or a standard Universal 1U Rack Shelf part 60 190 01 or 60 604 01 figure 2 On the standard rack shelf the BBG 6 A mounts in one of four locations to the rear of the rack or in one of four locations to the front of the rack BBG 6 A e Introduction 1 Installation 2 d ro Q8 d SS 2 VersaTools Rack Shelf 1 4 Rack Width False Front Face Plate 2 nd Y 8 Use 2 mounting holes 2 4 40 x 3 16 Screws on opposite corners Extron BBG6A Black Burst Color Bar Audio Generator Figure 1 Rack mounting the BBG 6 Aon a VersaTools shelf 1 Ifrubber feet were previously installed on the bottom of the unit remove them 2 Mountthe unit on the rack shelf using two 4 40 x 3
20. y if the fault has been caused by misuse improper handling care electrical or mechanical abuse abnormal operating conditions or non Extron authorized modification to the product If it has been determined that the product is defective please call Extron and ask for an Applications Engineer at 714 491 1500 USA 31 33 453 4040 Europe 65 6383 4400 Asia or 81 3 3511 7655 Japan to receive an RA Return Authorization number This will begin the repair process as quickly as possible Units must be returned insured with shipping charges prepaid If not insured you assume the risk of loss or damage during shipment Returned units must include the serial number and a description of the problem as well as the name of the person to contact in case there are any questions Extron Electronics makes no further warranties either expressed or implied with respect to the product and its quality performance merchantability or fitness for any particular use In no event will Extron Electronics be liable for direct indirect or consequential damages resulting from any defect in this product even if Extron Electronics has been advised of such damage Please note that laws vary from state to state and country to country and that some provisions of this warranty may not apply to you AM AN
Download Pdf Manuals
Related Search