Extron electronic Extron Electronics Switch 100 User's Manual
Contents
1. but external EDID has not been stored Factory default EDID is being used e Green EDID storage is enabled and external EDID is stored e Amber EDID storage is enabled and EDID is being loaded The LED turns green when stored Mount the HAE 100 If necessary mount the HAE 100 For mounting information see the HAE 100 User Guide Extron USA West Extron USA East Extron Europe Extron Asia Extron Japan Extron China Extron Middle East Headquarters 81 3 3511 7655 971 4 2991800 400 883 1568 81 3 3511 7656 FAX 971 4 2991880 FAX 8 2027 50 Rev A 1 714 491 1500 1 919 863 1794 31 33 453 4040 65 6383 4400 86 21 3760 1568 02 11 1 714 491 1517 FAX 1 919 863 1797 FAX 31 33 453 4050 FAX 65 6383 4664 FAX 86 21 3760 1566 FAX 800 633 9876 800 633 9876 800 3987 6673 800 7339 8766 Inside China Only Inside USA Canada Only Inside USA Canada Only Inside Europe Only Inside Asia Only 2011 Extron Electronics All rights reserved Www extron com2. the HDMI input 7 NPUT SIGNAL e HDCP This LED lights when the HDMI input signal is encrypted with High bandwidth Digital Content Protection HDCP e 2 CH PCM This LED lights when the embedded audio signal is 2 channel digital linear pulse code modulation LPCM HDCP 2 CH PCM BITSTREAM e Bitstream This LED lights when the embedded audio signal is a Dolby Digital or DTS format HAE 100 Setup Guide Continued Output LEDs e Signal This LED lights when the unit is providing video on the HDMI output connector OUTPUT SIGNAL e HDCP This LED lights when the HDMI output signal is encrypted with HDCP HDCP e Analog This LED lights when the unit is providing analog audio from the 3 5 mm 5 pole captive screw output connector ANALOG e S PDIF This LED lights when the unit is providing digital audio from the S PDIF RCA S PDIF output connector Config Port If necessary connect a control PC to this port using a USB cable Use this port to update firmware dll and check the status of various functions a Rear Panel Overview Audio Format Switch A toggle switch located on the rear panel is used for selecting the audio format that the ane HAE 100 will extract from the HDMI signal The position of this toggle switch also governs the FORMAT EDID presented to the source device connected to the input of the HAE 100 S PDIF ANALOG e Set this switch to the Analog u
3. lanced or unbalanced 3 5 mm 5 pole captive screw connector see figure 2 Step 5 Power On the HAE 100 and All Devices Wire the power supply see figure 3 and connect it to the power connector O When power is applied to the unit the front panel LED lights Connect the power cords of the input and output devices and turn them on The sound should be audible If an output display is connected to the HDMI output the picture should appear Front Panel Overview LEDs HAE 100 HDMI OUTPUT AUDIO EDID store ON AUDIO FORMAT ANALOG S PDIF gt oin Figure 1 HAE 100 Rear Panel CAUTION For unbalanced audio connect the sleeve s to the ground contact DO NOT connect the sleeve s to the negative contacts 5 mm MAX Do not tin the wires Tip Tip m OL 4 Ring NO GROUND a h Ola Sleeve s H Sleeve s E I OC a Tip p 1 3 NO GROUND ule S Unbalanced Output Balanced Output Figure 2 Analog Output Connector Wiring Smooth l Ridges A A SECTION A A eel Power Supply Tie Wrap gt Output Cord Eep Captive Screw Connector Figure 3 Power Supply Wiring These LEDs indicate the status of the input and output signal that is being sent through the HAE 100 and the devices that are connected to it Input LEDs e Signal This LED lights when the unit is receiving a signal from
4. p position to extract 2 channel stereo audio from the gt po i HDMI input signal A f AAA NOTE If the embedded audio is 2 channel LPCM the audio can be output from the analog output and the S PDIF output simultaneously e Set this switch to the S PDIF down position to extract digital S PDIF audio from the HDMI input signal Configuration DIP Switches A 2 pole DIP switch located on the rear panel is used to configure the following features HDMI OUTPUT AUDIO e EDID Store Set this switch to the On up position to enable the EDID store function see the EDID Store Button and LED section below Set this switch to the Off down STORE ON position to disable the EDID store function ON NOTE The EDID Store LED is unlit when this function is disabled O HH e HDMI Output Audio Set this switch to the On up position to send audio to the OFF HDMI output the Analog output and or the S PDIF output simultaneously Set this switch to the Off down position to send audio only to the analog output and or S PDIF output EDID Store Button and LED A recessed push button is used to store EDID from a display that is connected to the HDMI output With the EDID Store switch set to the On up position press the recessed push button to learn and store EDID information Use the LED to determine the status of the EDID storage e Off EDID storage is disabled Factory default EDID is being used e Red EDID storage is enabled
5. yt Ate a Extron Electronics o G INTERFACING SWITCHING AND CONTROL oro HAE 100 Setup Guide The Extron HAE 100 HDMI Audio De Embedder is used to extract embedded audio from an HDMI signal and output it as an analog stereo output or an S PDIF output This guide provides basic instructions for an experienced installer to set up and operate the HAE 100 Installation and service must be performed by authorized personnel only Installation Step 1 Turn Off the HAE 100 and All Devices Turn the input and output devices off and unplug their power cords Verify that the HAE 100 is disconnected from the power source before proceeding Step 2 Connect HDMI Input Device Connect an input device to the HDMI input connector Step 3 Connect HDMI Output Device If necessary connect an output device to the HDMI output connector NOTE Itis not required to connect an HDMI output device to extract audio from the HDMI input device Step 4 Connect Audio Output Devices The HAE 100 extracts audio using the following connectors Connect audio output devices to at least one of the following connectors e S PDIF output 4 This connector extracts digital S PDIF audio Connect an audio output device to this connector using an RCA cable e Analog output This connector extracts 2 channel stereo analog audio Connect an audio output device to this connector using a cable with a ba
Download Pdf Manuals
Related Search