Extron electronic Extron Electronics Projector Accessories 70-526-03 User's Manual
Contents
1. Secure a device to one side of the mounting bracket using two of the supplied 4 40 x 3 16 screws in opposite diagonal corners If a power supply is connected to the device use the two included tie wraps to strap the power supply to the bracket or attach a second device as described in step 4 Place the bracket around the projector ceiling mounting pole as shown at right Insert the two legs of the square U bolt through the slotted holes on the back side of Rubber Pad Ceiling Pole the bracket mount plate place them around the ceiling pole then insert the two legs ma through the round holes on the backing brace on Bracket 5S Backing Brace Mounting Plate e Fora typical 1 5 to 2 0 diameter pole You can use the supplied square U bolt which fits a typical ceiling pole For a smaller pole Locally obtain a square U bolt that fits your ceiling pole The slotted holes on the bracket can accomodate a square U bolt for pole sizes from 1 0 to 2 0 in diameter Move the PMK 250 up to the desired location on the ceiling pole as close to the ceiling as desired 9 Secure the back brace to the square U bolt using the included hex nuts washers and lock washers Tighten the hex nuts securely CAUTION Be sure to tighten the hex nuts securely enough that the PMK 250 does not slide down the ceiling pole A socket wrench is recommended to tighten the hex nuts Attaching the square U bolt 10 Secure the front panel to the mo2. PMK 250 Projector Mount Kit Instruction Card Part 70 526 02 and 70 526 03 The PMK 250 Low Profile Projector Mount Kit is an above projector mounting kit that can hold up to two quarter rack width products or one product and one power supply Each kit consists of a steel mounting bracket that is Rubber Pad available in black part 70 526 02 or white part 70 526 03 a square U bolt with a mounting brace plate and an assortment of adhesive backed cover sheets in black or white in four different sizes to cover the bottom opening of the bracket The bracket attaches to a 1 to 2 diameter projector mounting pole Its low 2 inch height allows it to be mounted in tight spaces between the projector and the ceiling while its depth of 8 75 enables it to accommodate a variety of device sizes Mounted Extron NS Extron Product PMK 250 Projector Mount Kit Mounting to the Projector Pole Sea Siasi Mount products on the PMK 250 bracket as follows PPly 1 Remove the front panel from the PMK 250 using an Extron Tweeker provided or other small Philips screwdriver Retain the four screws to reattach the plate when finished Remove the protective backing from the self adhesive rubber pad and place the pad on the PMK 250 mount plate centering it between PMK 250 with an Extron product the two holes see drawing at right and power supply mounted Remove any rubber feet from the bottom of the device s to be mounted
3. unting tray with four of the included 6 screws 11 If desired choose one of the four sizes of self adhesive cover sheets and apply it to the underside of the mounting tray Extron Flectronics USA Extron Electronics Europe Extron Electronics Asia Extron Electronics Japan 1230 South Lewis Street Beeldschermweg 6C 135 Joo Seng Road 04 01 Kyodo Building Anaheim CA 92805 3821 AH Amersfoort PM Industrial Building 16 Ichibancho USA The Netherlands Singapore 368363 Chiyoda ku Tokyo 102 0082 Japan 714 491 1500 31 33 453 4040 65 6383 4400 81 3 3511 7655 68 1124 01 Rev A www extron com Fax 714 491 1517 Fax 31 33 453 4050 Fax 65 6383 4664 Fax 81 3 3511 7656 08 05 2 g Ww
Download Pdf Manuals
Related Search