Euro-Pro VPW40 User's Manual
Contents
1. Hold trigger down Allow water to flow through the pump for 30 seconds Check hose for kinks or leaks open tap fully Clean the air intake vents Check amp clean filter Check that the voltage is adequate SAFETY amp WARNING INSTRUCTIONS For safety reasons it is recommended that you read this manual before attempting to operate this appliance Failure to follow these instructions can result in personal injury or equipment problems To help recognize note the following symbols AX DANGER Danger indicates an imminently hazardous situation which if not avoided WILL result in death or serious injury A WARNING Warning indicates a potentially hazardous situation which if not avoided COULD result in death or serious injury A CAUTION Caution indicates a potentially hazardous situation which if not avoided MAY result in death or serious injury NOTE Information that requires special attention Important Safety Instructions SAVE THESE INSTRUCITONS When using this product basic precautions should always be followed including the following Ay DANGER 1 Read all instructions before using the product 2 To reduce the risk of injury close supervision is necessary when this product is used near children 3 Always disconnect power electric units before disassembling repairing or changing attachments on the unit 4 Follow all safety codes as well as the Occupational Safety and Hea2. outlet and turn the unit to the On position 7 Now you are ready to use the pressure washer Disengage the safety lock and depress the trigger on the trigger gun
3. CTIONS When you wish to stop using the pressure washer temporarily make sure that the safety lock has been engaged to avoid any accidental operation Fig 6 Fig 6 Using the High Pressure lance The high pressure lance may be used alone or with the detergent applicator bottle Add detergent to the bottle and then attach the detergent applicator bottle to the high pressure lance just push it on the end of the high pressure lance Fig 7 amp 8 Toremove the detergent applicator bottle lift the tab on the top of the connector and pull off Maintenance amp Cleaning Lubrication The pressure washer is supplied with a closed lubrication system so no addition of oil is needed Checking the Water Intake Filter The water intake filter is located inside the water intake connector Fig 9 Remove periodically and inspect for any deposits that might accumulate there Hose Connector Water Intake Fig 9 Cleaning the Nozzles If you notice that the output pressure fluctuates you may have to clean the nozzles Turn the unit Off Unplug from electric outlet and disconnect the water supply Remove the lance and hose with the trigger gun from unit Take the small metal pin provided and insert into the nozzle end to remove any obstructions Fig 10 Fig 10 This will occur more frequently if your water supply is very hard When using your pressure washer always have it in the horizontal position as sh
4. EURO PROX PRESSURE WASHER OWNER S MANUAL Model VPW40 120V 60 Hz 12 5 Amps For information or assistance EURO PRO Operating LLC 21 Lawrence Paquette Industrial Drive Champlain NY 12919 Tel 1 800 798 7398 www euro pro com wo EURO PRO X ONE 1 YEAR LIMITED WARRANTY EURO PRO Operating LLC warrants this product to be free from defects in material and workmanship for a period of one 1 year from the date of the original purchase when utilized for normal household use subject to the following conditions exclusions and exceptions If your appliance fails to operate properly while in use under normal household conditions within the warranty period return the complete appliance and accessories freight prepaid to EURO PRO Operating LLC 21 Lawrence Paquette Industrial Drive Champlain NY 12919 If the appliance is found by EURO PRO Operating LLC to be defective in material or workmanship EURO PRO Operating LLC will repair or replace it free of charge Proof of purchase date and 16 95 to cover the cost of return shipping and handling must be included Non durable parts including without limitation hose lance and electrical parts which normally require replacement are specifically excluded from warranty The liability of EURO PRO Operating LLC is limited solely to the cost of the repair or replacement of the unit at our option This warranty does not cover normal wear of parts and does not apply to any unit th
5. at has been tampered with or used for commercial purposes This limited warranty does not cover damage caused by misuse abuse negligent handling or damage due to faulty packaging or mishandling in transit This warranty does not cover damage or defects caused by or resulting from damages from shipping or repairs service or alterations to the product or any of its parts which have been performed by a repair person not authorized by EURO PRO Operating LLC This warranty is extended to the original purchaser of the unit and excludes all other legal and or conventional warranties The responsibility of EVRO PRO Operating LLC if any is limited to the specific obligations expressly assumed by it under the terms of the limited warranty In no event is EURO PRO Operating LLC liable for incidental or consequential damages of any nature whatsoever Some states do not permit the exclusion or limitation of incidental or consequential damages so the above may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state Important Carefully pack item to avoid damage in shipping Be sure to include proof of purchase date and to attach tag to item before packing with your name complete address and phone number with a note giving purchase information model number and what you believe is the problem with item We recommend you insure the package as damage in shipping is not covered by yo
6. e On position after that press the trigger the Automatic Stop System will start the machine and will stop it automatically when the trigger is released It is advisable to put on the safety lock of the trigger whenever the machine is stopped in order to avoid unintentional starting Any automatic start of the machine without pressing the trigger is attributable to air bubbles in the water or other similar phenomena which do not imply the existence of any defects in the machine Do NOT leave the appliance unattended during the standby for more than 5 minutes Contrarily for the safety of the appliance it is necessary to re turn the On Off switch to the Off position Please check that the coupling of the high pressure hose with the appliance and the trigger gun supplied as standard equipment is made correctly that is to say without any water leak Attaching High Pressure Hose to Pressure Washer Once the pressure washer is assembled you are ready to use the unit 1 While facing the front side of the unit attach the high pressure hose to the high pressure output connector on the right side of the unit Twist on tight to avoid leakage Fig 3 3 Once the high pressure hose is connected to the unit you can attach the lance to the end of the trigger gun Fig 4 Fig 4 To attach the lance to the trigger gun hold the trigger gun in your left hand insert the lance and push it in all the way into the con
7. ever try to stop or deflect leaks with any body part e Always engage the trigger safety latch in the safe position when spraying is stopped even if only for a few minutes e Always follow detergent manufacturer s label recommendations for proper use of detergents Always protect eyes skin and respiratory system from detergent use SERVICING OF A DOUBLE INSULATED APPLIANCE In a double insulated product two systems of insulation are provided instead of grounding No grounding means are provided for a double insulated product nor should grounding means be added to the product Servicing a double insulated product requires extreme care and knowledge of the system and should be done only by qualified service personnel Replacement parts for a double insulated product must be identical to the original parts A double insulated product is marked with the words double Insulation or Double Insulated Product may also be marked with symbol shown SAFETY amp WARNING INSTRUCTIONS continued A WARNING Do not use pressure that exceeds the operating pressure of any of the parts hoses fittings etc in the pressurized system Ensure that all equipment and accessories are rated to withstand the maximum working pressure of the unit A WARNING Explosion hazard e NEVER spray flammable liquids of use pressure washer in areas containing combustible dust liquids or vapors NEVER operate this machine in a closed buildin
8. g or in or near an explosive environment A WARNING Do not spray electrical apparatus or wiring e NEVER disconnect the high pressure discharge hose from the machine while the system is pressurized To depressurize the machine turn the power and water supply off then press the gun trigger 2 3 times NEVER permanently engage the trigger mechanism on the gun NEVER operate the machine without all the components properly connected to the unit handle gun lance assembly nozzle etc A WARNING Equipment damage e ALWAYS turn water supply ON before turning the pressure washer ON Running pump dry causes serious damage Do not operate the pressure washer with the inlet water screen removed Keep screen clear of debris and sediment NEVER operate pressure washer with broken or missing parts Check equipment regularly and repair or replace worn or damaged parts immediately Use only the nozzle supplied with this machine Never leave the lance unattended while the machine is running Never attempt to alter factory settings Altering factory settings could damage the unit and will void the warranty i Always hold gun and lance firmly when starting and operating the machine NEVER allow the unit to run with the trigger released OFF for more than one minute Resulting heat buildup will damage pump NEVER store the pressure washer outdoors or where it could freeze The pump will be seriously damaged Release tri
9. gger when changing from high to low pressure modes Failure to do so could result to damage to the nozzle This unit must always be used in the horizontal position A CAUTION Keep hose away from sharp objects Bursting hose may cause injury Examine hoses regularly and replace if damaged Do not attempt to mend a damaged hose EXTENSION CORDS AX DANGER If using an extension cord use only grounded three wire extension cords that are in good condition Use only extension cords that are intended for outdoor use These extension cords are identified by a marking Acceptable for use with outdoor appliances store indoors while not in use use only extension cords having an electrical rating not less than the product Do not use damages extension cords Examine extension cord before using and replace if damaged Do not abuse extension cord and do not pull on the cord to disconnect Keep cord away from heat and sharp edges Always disconnect from the receptacle before disconnecting the product from the extension cord Note Do not use 16 or 18 AWG extension cords on this product AX DANGER Failure to follow these instructions can result in serious injury including death To reduce the risk of electrocution keep all connections dry and off the ground Do not touch the plug with wet hands OPERATING INSTRUCTIONS Storing Your Pressure Washer When you have finished using your pressure washer follow these step
10. ional protection from the risk of electrical shock When connecting the GFCI to the electrical outlet the indicator should appear red If the indicator is not red depress the RESET button on the GFCI until the indicator appears red Cleaning Tips Wood Decks Rinse deck and surrounding area with fresh water If using detergent fill the detergent applicator bottle and apply to the area being cleaned For optimal results reduce your work area to small sections and clean each section one at a time Allow the detergent to rest on the surface for a few minutes and then rinse at high pressure Do not let the detergent dry on the deck Always clean from left to right and top to bottom for best results Rinse at high pressure using the lance keeping the tip of the spray nozzle 8 12 inches from the surface Caution For soft woods increase the distance from the cleaning surface Cars Boats amp Motorcycles Wet down area to be cleaned before applying detergent with clean water Fill the detergent applicator bottle and apply to the area being cleaned To achieve best results clean one side at a time Allow the detergent to rest on the surface for a few minutes but do not let it dry Rinse at high pressure using the fan jet ina sweeping motion keeping the tip of the spray nozzle at least 8 10 inches away from the surface Maintain a further distance when using a direct spray Wipe surface for a polished finish OPERATING INSTRU
11. lth Act OSHA 5 Ensure safety devices are operating properly before each use DO NOT remove or modify any part of the gun or unit 6 Know how to stop this unit and relieve pressure quickly Be thoroughly familiar with the controls 7 Stay alert Watch what you are doing 8 Do not operate this unit when fatigued or under the influence of alcohol or drugs Rev 11 03 9 Keep operation area clear of all persons 10 Do not overreach or stand on unstable support Keep good footing and balance at all times 11 Follow maintenance instructions specified in this manual 12 This product shall be connected to a power supply receptacle protected by a ground fault circuit interrupter GFCI electric power washers only 13 If product is provided with a GFCI be sure to inspect the cord and GFCI prior to use Any repair or replacement of the power cord must be performed by a qualified licensed or certified electrical technician Risk of injection or severe injury Keep clear of nozzle Do not discharge streams at persons This product is to be used only by trained operators Always remove lance irom gun before cleaning debris from tip e Keep clear of nozzle NEVER direct high J spray at any person animal or self e Always wear safety goggles or glasses and protective clothing when operating performing maintenance or changing accessories e Never put hands or fingers over the spray tip while operating the unit e N
12. nector on the trigger gun and turn it clockwise 60 until it locks in place To remove the lance push down on the attachment and turn counter clockwise 60 and then pull out Make sure that the lance is securely locked in place before use OPERATING INSTRUCTIONS Garden Hose Connection Once the high pressure hose is attached to the pressure washer you can connect the garden hose to the unit Before attaching the garden hose coupling to the unit make sure that the water intake filter is inside the water intake connector on the unit 1 Attach the male adapter supplied to the water intake connector on the left hand side of the unit Fig 5 2 Attach the female hose coupling to the garden hose Fig 5 3 Connect the female hose coupling to the male adapter making sure that it is tightly secured in place Fig 5 Fig 5 4 After all the connections have been made and BEFORE you plug the pressure washer into an electrical outlet open the water supply and press on the trigger switch in order to remove any air which may be in the hose or pump Continue to press on the trigger switch until you get a constant flow of water coming out of the trigger gun Allow water to flow for 30 seconds 5 Once this is accomplished stop pressing the trigger switch Engage the safety lock on the trigger 6 Ensure that the On Off switch at the rear of the unit is on the Off position then plug the unit into an electrical
13. own below NEVER CORRECT WRONG GETTING TO KNOW YOUR PRESSURE WASHER 1 High Pressure Lance 9 Inlet Water Filter 2 Trigger Gun 10 Garden Hose Coupling 3 High Pressure Hose 11 High Pressure Output 4 High Pressure Hose Connector 12 Handle 5 Safety Lock 13 Pressure Washer 6 Trigger 14 Detergent Applicator Bottle 7 On Off Switch 15 Wheels x2 8 Water Intake Valve 16 Handle Screw x1 not shown Illustrations may differ slightly from actual product Technical Specifications Voltage 120V 60Hz Power 12 5 Amps Pressure 1300 psi max Flow Rate 1 45 gpm OPERATING INSTRUCTIONS Suitable Use of Your Pressure Washer This high pressure washer is suitable for non professional use The working temperature must range between 40 F and 120 F The machine is supplied with a trigger gun equipped with a trigger handle to offer a comfortable working position The high pressure washer is suitable for washing with cold water only The water that you use for the pressure washer must not be dirty sandy or contain any corrosive chemical products The pressure washer may be used to wash shutters doors tiles cars decks campers etc where high water pressure is necessary to remove dirt With the detergent applicator bottle the pressure washer can be used to apply a thick coating of aerated detergent to the areas being cleaned When using the pressure washer we recommend the use of personal
14. s for safe storage 1 Turn the pressure washer to the Off position 2 Turn off the water supply 3 Before disconnecting the high pressure hose connection point the trigger gun in a safe direction away from you and discharge the high pressure water Disconnect the high pressure hose from the pressure washer 4 Disconnect garden hose from pressure washer 5 Remove excess water from the pump by tipping the unit on both sides to drain any remaining water from the water intake and outlet fittings Drain detergent applicator bottle and flush with clean water Wipe away any remaining water on all parts and fittings Engage the trigger gun safety lock Store the unit and accessories in a room above 32 F Ol oy R Winterizing amp Long Term Storage 1 Disconnect all water connections 2 Turn the pressure washer on for a few seconds until any remaining water in the pump exits 3 Turn the unit off immediately 4 Store the pressure washer parts and accessories in an area with a temperature above 32 F Motor Thermostat Important This pressure washer is equipped with a motor thermostat The motor will stop if it is overheating Wait 10 20 minutes before starting the unit again If it stops again please call customer service at 1 800 798 7398 Ground Fault Circuit Interrupter GFCI This unit is equipped with a Ground Fault Circuit Interrupter GFCI built into the plug This device provides addit
15. safety items to reduce the risk of accidental injury s Unpacking Your Pressure Washer After you open the package check to make sure that all the parts are in the box as per parts that illustrated on page 3 of this guide Due to transport and packing restraints some accessories may be supplied unassembled in this case follow the assembly instructions in this manual If you have any questions call Customer Service at 1 800 798 7398 Keep all small and potentially harmful parts of the package plastic bags foamed polystyrene nails etc out of the reach of children Correct Use of the Pressure Washer e Place the pressure washer in a safe area and on a horizontal surface e When using the pressure washer hold the trigger gun firmly with one hand on the handle and the other on the lance Fig 1 Fig 1 e NEVER point the water jet at electric wiring at the pump unit or at any person or animal Assembling the Pressure Washer 1 Carefully take the pressure washer and all accessories out of the packaging 2 Snap wheels onto the unit Fig 2 3 Attach the handle to the unit with the screw supplied using a Phillips screwdriver Fig 2 Fig 2 AUTOMATIC STOP SYSTEM PLEASE NOTE This pressure washer is equipped with the Automatic Stop System which stops the unit during the bypass stage To start the pressure washer it is therefore necessary to set the On Off switch to th
16. ur warranty Mark the outside of your package ATTENTION CUSTOMER SERVICE We are constantly striving to improve our products therefore the specifications contained herein are subject to change without notice Printed in Italy 9 TROUBLE SHOOTING PROBLEM POSSIBLE REASON PRESSURE WASHER WILL NOT START WHEN THE ON OFF SWITCH IS IN THE ON POSITION PUMP DOESN T REACH ADEQUATE PRESSURE OR CAVITATES PRESSURE WASHER HAS OR WILL NOT MAINTAIN PRESSURE PRESSURE WASHER MAKES EXCESSIVE NOISE MOTOR DOES NOT RUN CONTINUOUSLY WHEN TRIGGER IS SQUEEZED MOTOR BUZZES WHEN TURNED ON BUT DOES NOT START MOTOR STOPS RUNNING WHILE UNIT IS IN USE Electrical socket is faulty or breaker has tripped Voltage is inadequate GFCI has tripped Power cord is not plugged in Water intake filter is clogged Pump is drawing air Diameter of garden hose is too small Water supply is restricted Excessive air in waterline and pump Water supply is restricted Air intake is blocked Water intake filter is dirty Net voltage is lower than suggested POSSIBLE SOLUTION Check plug socket fuses breaker Check that the voltage is adequate Reset Try another electrical outlet Plug in power cord Remove and clean water intake filter Tighten connections bleed system Replace with 3 4 inch garden hose Check hose for kinks or leaks open tap fully Turn unit and water supply off Bleed system
Download Pdf Manuals
Related Search