Euro-Pro IR4005 User's Manual
Contents
1. Anti Calc Cassette and pull it out of the water tank 4 Fill the water tank up to the Max mark as shown below in fig 3 Water Tank Lock a he 4 _ i ae if i i Fa T rom of ill AL a ae Wh Ten i S ON jn 4 n a ns a ee w T J as j n A A i fad a a 1 ities a Fig 2 lt _ _ __ Slide Out Fig 3 5 Return the water tank to its place under the iron stand Note Make sure that the water tank is pushed back to its place and the lock is closed If the water tank is not in its place it will not be able to deliver water from the pump to the iron Setting the Ironing Temperature e Place the iron on the rubber mat on the water tank e Plug the power cord into the electrical outlet e Select the required temperature setting on the temperature control dial using the Ironing Chart on page 6 e The temperature pilot light will come On indicating that the iron is heating up e When the temperature pilot light has gone Off the set temperature has been reached and the iron is ready for use To select iron temperature align temperature selected on dial with the indicator on the water tank NOTE Before starting to iron delicate fabrics it is best to first test the temperature of the iron on a hem or an inside seam DIRECTIONS ON LABEL Synthetic fs fibers e g FABRIC S acryl viscose 7 polya2. plug does not fit fully into the outlet reverse the plug If it still does not fit contact a qualified electrician Do no attempt to defeat this safety feature SAVE THESE INSTRUCTIONS For Household Use Only 1 Rev 05 02A Model IR4005 LIMITED WARRANTY EURO PRO Operating LLC warrants this product to be free from defects in material and workmanship for a period of one 1 year from the date of purchase The liability of EURO PRO Operating LLC is limited solely to the repair or replacement of the product at it s option This warranty does not cover damage caused by misuse negligence use on improper current or voltage use contrary to operating instructions or disassembly repair or alteration by any person other than EURO PRO Operating LLC Product repair or replacement at our option is your sole remedy This warranty excludes all other legal and or conventional warranties The responsibility of EYURO PRO Operating LLC if any is limited to the specific obligations expressly assumed by it under the terms of the limited warranty In no event is EURO PRO Operating LLC liable for incidental or consequential damages of any nature whatsoever Some States do not permit the exclusion or limitation of incidental or consequential damages so the above may not apply to you This warranty gives you specific legal rights which vary from state to state If you have a claim under this warranty or if you require service DO NOT RETURN THIS PR
3. position Always allow iron sufficient time to heat up thermostat light goes off before pressing the steam button e Overuse of steam burst Allow more time between each burst e Iron may have been overfilled Turn iron off empty water and follow instructions for filling e Steam performance may be low if iron requires seasoning To season use regular tap water for 1or 2 tanks until steam performance improves ADDITIONAL IMPORTANT SAFEGUARDS 1 Your Steam Station iron is designed to rest only on the iron rest provided with the iron Do not rest iron on soleplate 2 Never use or rest iron on an unstable surface 3 While the iron is hot never set iron on an unprotected surface even if it is on its heel rest 4 WARNING TO PREVENT ELECTRIC SHOCK OR OTHER INJURY before filling the iron with water make sure that the plug is removed from the outlet 5 CAUTION Never fill the iron with fabric conditioner starches or any other solution as these will damage the steam mechanism Do not use contaminated water 6 WARNING TO AVOID FIRE never leave iron unattended while it is plugged in 7 WARNING TO PREVENT ELECTRIC SHOCK never immerse the iron in water or other liquid 8 WARNING TO PREVENT ELECTRIC SHOCK never use the iron in a location where it can fall or be pulled into water or any other liquid If the iron falls into water or any other liquid unplug it immediately DO NOT reach into the w
4. upside down there may be hot water in the reservoir 10 Never direct steam at any person especially when using the iron ina vertical position The steam is very hot and could cause burns 11 The use of accessory attachments not recommended by EURO PRO Operating LLC may result in fire electrical shock or personal injury 12 Do not operate in the presence of explosive and or flammable fumes 13 Make sure that the cord set never touches the iron soleplate when it is hot 14 This appliance is for household use only airs INSTRUCTIONS To avoid a circuit overload do not operate another high wattage appliance on the same circuit 2 If an extension cord is absolutely necessary use a 13 ampere cord Cords rated for less amperage may overheat Use care to arrange the cord so that it cannot be pulled or tripped over WARNING Water must first be pumped look for pump light to be illuminated from the water tank to the iron before steam will exit water requires approximately 2 minutes to pass through the hose and reach the iron Once this is done you will not have to wait again you will have continuous steam if you keep pump on Please note though that you must also adjust variable steam to desired output level or steam will not exit the iron POLARIZED PLUG This appliance has a polarized plug one blade is wider than the other As a safety feature this plug will fit into a polarized outlet only one way If the
5. AM 5 00 PM Eastern Standard Time or visit our website at www euro pro com OPERATING INSTRUCTIONS CONT lroning With Steam Always read garment labels and follow the manufacturer s ironing instructions Refer to the Ironing Chart on page 6 for temperature recommendations e Use low settings for synthetics and silks ee Use moderate settings for wool and blends eee Use high settings for cottons and linens e Make sure that the steam station is plugged into the electrical outlet e Set the temperature dial to the desired temperature Fig 4 e Fill the water tank with water following the instructions on page 5 for filling the water tank e Make sure that the iron is resting on top of the rubber mat on the water tank stand e When steam is desired simply push the steam button Important Do NOT remove rubber mat from water tank and place on a table or any other surface which may be damaged by heat Moderate Steam N Maximum Steam Fig 4 Important Make sure that the iron has reached the selected temperature before using steam Steaming in a Vertical Position For vertical steaming simply lift the iron in a vertical position and press the steam button See fig 5 Fig 5 lroning With No Steam All marked settings on the temperature control dial can be used for dry ironing 1 Plug the cord into a polarized 120V AC electrical outlet The Temperature Pilot light wi
6. a E the o i pressing the steam button several ee ANANO ier Co OOW l 4 Scale and other deposits can be before you store it umes wiped off the soleplate with a damp e Regularly check if the power cord is cloth and some non scratching fluid still in a good and safe condition abrasive ir Temperature Control Dial Rotate Dial 5 Keep the soleplate smooth avoid 2 Steam Button hard contact with metal objects 3 Temperature Pilot Light 4 Iron Stand 6 From time to time clean the inside of 5 Water Tank the water tank by filling with water 6 Water Filling Hole and shaking 7 Rubber Mat 8 Power Cord 9 Connecting Hose Supply Hose HOW TO REPLACE THE ANTI CALC CASSETTE 10 Anti Calc Cassette 11 Water Tank Lock 12 Pump On Light e The Anti Calc cassette should be replaced after 9 12 months of usage depending on the amount of usage and water hardness e Rotate and release the head of the cassette then take it out e Empty the water from the water tank and cassette housing e Fill the water tank with water e Insert the new cassette and lock it into the water filling hole e Push steam button for about one minute The new cassette is now filled with water e You can resume ironing Technical Specifications Voltage 120V 60HZ Power 1400 Watts To order additional Anti Calc cassettes or for customer service Call Customer Service In US 800 798 7398 Monday to Friday 8 30
7. ODUCT TO THE STORE Send the product postage prepaid to In U S A EURO PRO Operating LLC 21 Lawrence Paquette Ind Dr Champlain NY 12919 Tel 800 798 7398 Please include a copy of your sales receipt 9 50 to over the cost of return shipping amp handling and a letter explaining the nature of your difficulty Do not forget to enclose your name address and telephone number If the warranty period has expired please send your iron postage pre paid to In U S A Service Department EURO PRO Operating LLC 21 Lawrence Paquette Ind Dr Champlain NY 12919 Tel 800 798 7398 You will be advised of the cost of repair before any servicing is done unless you enclose a note indicating that you would like us to proceed with the repairs and return the iron to you C O D N PRODUCT REGISTRATION CARD Please complete and return within ten 10 days of purchase The registration will enable us to contact you in the event a product defect is discovered By returning this card you acknowledge to have read and understood the instructions for use and warnings set forth in the accompanying instructions RETURN TO EURO PRO Operating LLC 21 Lawrence Paquette Ind Dr CHAMPLAIN N Y 12919 PRC HACER soseceaci singh wianacaennadn serendahasscosicaniduncacsshatescucnlsdslseca tan decbasncthiccdecncheedchesuenbsiccateke PRE SS essen chi cg exec rcs nda sano gta nel ten coche nhc ce sbcssh tive cdo ead DATE OF PURCHASE cccceeecesese
8. OWNER S MANUAL EURO PROX Steam Station Model IR4005 For information or assistance EURO PRO Operating LLC 21 Lawrence Paquette Ind Dr Champlain NY 12919 Tel 800 798 7398 www euro pro com IMPORTANT SAFETY INSTRUCTIONS When using your iron basic safety precautions should always be followed including the following 1 Read all instructions carefully 2 Use iron only for its intended use 3 To protect against risk of electrical shock do not immerse the iron in water or other liquids Always turn the iron to OFF before plugging in or unplugging from outlet 4 Never yank cord to disconnect from outlet Grasp plug and pull to disconnect 5 Do not allow cord to touch hot surfaces Let iron cool completely before putting away 6 Always disconnect iron from electrical outlet when filling with water emptying or when not in use 7 Do not operate iron with a damaged cord or after the iron has been dropped or damaged in any manner To avoid the risk of electric shock do not disassemble the iron Send it to EURO PRO Operating LLC for examination and repair Incorrect re assembly can cause the risk of electric shock when the iron is used 8 Close supervision is necessary for any appliance being used by or near children Do not leave iron unattended while connected or on an ironing board 9 Burns can occur from touching hot metal parts hot water or steam Use caution when you turn a steam iron
9. ater or liquid 9 CAUTION Never use scouring pads abrasive or chemical cleaners or solvents to clean the exterior or soleplate of your iron Doing so will scratch and or damage the surface 10 WARNING DO NOT aim iron at face towards yourself or anyone else while using or adjusting steam Burns or serious injury may occur 11 Always store your iron on the iron rest provided with your iron not on the soleplate If stored face down even the smallest amount of moisture will cause the soleplate to corrode and stain 12 DANGER Never use the iron if it is damaged or dropped Using the iron when it is damaged could create the risks of fire electric shock injury or death GETTING TO KNOW YOUR STEAM STATION IRON USER MAINTENANCE INSTRUCTIONS Before pate ioe a arith ets Ha a au and should not reoccur Cleaning the Iron Storage remove any labels stickers or tags tha after initial heating 1 Unplug the steam station from the Remove the power cord from the may be attached to the body or Also before ironing with steam for the soleplate of the iron first time allow iron to heat hold in a Pe i aaenaaine waterourorine When turned on for the first time your horizontal position and hit the steam 2 When finished using the iron turn aira new iron may emit an odor for up to 10 button several times The iron may emit the temperature control dial to MIN Set the steam control to position 0 a a the S here
10. ceeees MODELModel IR4005 SERIAL NO ooa NAME AND ADDRESS OF STORE Ariusia ari aaae aA Aaina TROUBLESHOOTING PROBLEM POSSIBLE REASONS amp SOLUTIONS lron does not heat Thermostat ready light goes On and Off Some odor or small particles come out of steam vents of new iron Iron does not steam Water droplets coming from steam vents Printed in China e Iron should be plugged into a 120V AC electrical outlet only Make sure that the plug is securely in the socket e Temperature setting too low Turn to higher setting e Iron not properly placed in stand e This is normal The light goes On and Off as the thermostat is switching the heating element On and Off to maintain the selected temperature e This is normal Follow instructions for first use and allow iron to steam through 2 3 fillings amp press the steam burst button occasionally to eliminate small white particles e Water tank may be empty or water level is very low Add water e Make sure that the temperature control dial is correctly set For maximum steam temperature control dial should be set on ee e Make sure the temperature control dial is set in the correct steam area e g for more steam turn temperature dial to higher setting e g e e e If temperature setting is correct and there is no steam gently tap the soleplate on the ironing board a few times e Iron may not be hot enough Set temperature control dial to the Max
11. e page 5 e Set the temperature control dial to its highest level e When the Temperature Pilot Light goes off indicating that the iron has reached its selected temperature Then e Push the steam button to activate the internal water pump e Steam will come out after about 2 minutes Please be patient for the first usage after which there will be no further waiting e Iron ona piece of cloth towel for 2 minutes e Place the iron on the rubber mat and allow it to steam for 5 minutes Rubber Mat Please note that during transportation the rubber mat may come off its place e The iron stand has 5 holes on the circumference of its top e The rubber mat has 5 pins in the corresponding locations e Place the rubber mat on top of the iron stand and push each individual pin into its hole Important Never place the hot iron on the plastic iron stand without the rubber mat on top of the iron stand See fig 1 e Do not place the rubber mat alone on a table or any other surface which may be damaged by heat OPERATING INSTRUCTIONS CONT IRONING CHART Filling the Water Tank Steam irons should be used with tap water up to 3 mmol l alkaline earth ions check the degree of hardness of your water with your local water authority or a mixture of distilled demineralized water with tap water If your tap water is very hard you can mix 1 1 distilled demineralized water with minera
12. l water so that your steam performance will be good Never use water containing additives battery top up water from service stations water from household softening systems or descaling agents Distilled Demineralized Water This should normally be mixed 1 1 with tap water The use of pure distilled demineralized water creates difficulties with steam production and can cause water to escape through the soleplate formation of drops Note If water escapes through the soleplate while you are using distilled demineralized water we recommend you use tap water 3 or 4 times Water with Additives Starch conditioner perfume and fabric conditioner should never be added to the water These result in residues in the steam chamber which will damage your iron and stain your laundry For this reason no condensed water water from driers may be used as this can contain additives e g conditioner Descaling the Iron Do not use chemical descaling agents as these can cause damage to the iron and stain your laundry Water From Household Water Softening Systems Do not use water from household water softening systems because even though these systems remove calcium from the water they add other substances to it Therefore this water is not suitable for steam irons Filling the Water Tank 1 Push down the water tank lock 2 Slide out the water tank from under the iron stand Fig 2 3 Rotate slightly the top of the
13. ll come on indicating that the iron is receiving power 2 Turn temperature dial to MIN 3 Turn the temperature control dial to the desired setting See Ironing Chart for a guide to temperature selection 4 Place iron on its rubber mat on the water tank while iron is warming to desired temperature 5 When the temperature pilot light goes the iron is ready for ironing OPERATING INSTRUCTIONS Before First Use Remove any labels stickers or tags which may be attached to the body or the soleplate of the iron before using the iron Read all instructions carefully Always follow the Important Safeguards Important The first time an iron is used some odor and small white particles may come out of the steam vents This is perfectly normal and will cease to occur after the iron has been in use for a short while Before you start using your iron follow the instructions in manual and do the following in order to eliminate any odor and small white residue particles and to ensure optimum steam performance How the Water is Pumped to the Iron 1 The water is pumped from the water tank to the iron through the supply hose by a built in water pump 2 This water pump is activated by pushing on the steam button The water pump pilot light will go on 3 The water pump will stay activated as long as your finger pushes the steam button e Fill the water tank according to instructions on filling Se
14. mide nylon polyester COTTON LINEN JEU SJOU BSED q F Hi YW 3 rr D D o O 3 D S 3 a l TEMP CONTROL STEAM BUTTON Ironing Temperature Always check first to see whether a label with ironing instructions is attached to the article to be ironed See table above Follow these ironing instructions in all cases If ironing instructions are missing but you do know the kind of fabric then see the table The table is valid for the materials only and is not applicable to any applied finish gloss etc Fabric to which some kind of finish has been applied gloss wrinkles relief etc can be ironed at the lowest temperature such as those made of synthetic fibers Sort the laundry out according to ironing temperature first wool with wool cotton with cotton etc The iron heats up quicker than it cools down Therefore start ironing the articles requiring the lowest temperature such as those made of synthetic fibers If the fabric consists of various kinds of fibers you must always select the lowest ironing temperature of the composition of those fibers For example an article consisting of 60 polyester and 40 cotton should be ironed at the temperature indicated for polyester and without steam If you do not know what kind s of fabric s the article has been made of find a spot which will be invisible when wearing or using the article Try out the ironing temperature which is most suitable the
15. re Start at a relatively low temperature Pure woolen fabrics 100 wool may be pressed with the iron set to a steam position Preferable set the steam control to maximum position and use a dry pressing cloth When steam ironing woolen fabrics shining of the fabric may occur This can be prevented by turning the article inside out and ironing the reverse side Velvet and other textures which rapidly acquire shiny spots should be ironed in one direction only with the nap applying light pressure Always keep the iron moving Iron the reverse side of synthetic materials and silk to prevent shining spots Do not use the spray button to prevent stains 5 I T gt ra 4 O m m O gt Z zZ O w m J O Z m 9
Download Pdf Manuals
Related Search